Spracherkennung für: .dtsi vermutete Sprache: Unknown {[0] [0] [0]} [Methode: Schwerpunktbildung, einfache Gewichte, sechs Dimensionen]
// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
/*
* Copyright 2017 Gateworks Corporation
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
/ {
/* these are used by bootloader for disabling nodes */
aliases {
ethernet0 = &fec;
ethernet1 = &lan1;
ethernet2 = &lan2;
ethernet3 = &lan3;
ethernet4 = &lan4;
led0 = &led0;
led1 = &led1;
led2 = &led2;
usb0 = &usbh1;
usb1 = &usbotg;
};
chosen {
stdout-path = &uart2;
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm4 0 5000000 0>;
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <7>;
};
gpio-keys {
compatible = "gpio-keys";
user-pb {
label = "user_pb";
gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
};
user-pb1x {
label = "user_pb1x";
linux,code = <BTN_1>;
interrupt-parent = <&gsc>;
interrupts = <0>;
};
key-erased {
label = "key-erased";
linux,code = <BTN_2>;
interrupt-parent = <&gsc>;
interrupts = <1>;
};
eeprom-wp {
label = "eeprom_wp";
linux,code = <BTN_3>;
interrupt-parent = <&gsc>;
interrupts = <2>;
};
tamper {
label = "tamper";
linux,code = <BTN_4>;
interrupt-parent = <&gsc>;
interrupts = <5>;
};
switch-hold {
label = "switch_hold";
linux,code = <BTN_5>;
interrupt-parent = <&gsc>;
interrupts = <7>;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_leds>;
led0: led-user1 {
label = "user1";
gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
default-state = "on";
linux,default-trigger = "heartbeat";
};
led1: led-user2 {
label = "user2";
gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
default-state = "off";
};
led2: led-user3 {
label = "user3";
gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
default-state = "off";
};
};
memory@10000000 {
device_type = "memory";
reg = <0x10000000 0x40000000>;
};
pps {
compatible = "pps-gpio";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pps>;
gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
};
reg_1p0v: regulator-1p0v {
compatible = "regulator-fixed";
regulator-name = "1P0V";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
reg_usb_h1_vbus: regulator-usb-h1-vbus {
compatible = "regulator-fixed";
regulator-name = "usb_h1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
};
reg_usb_otg_vbus: regulator-usb-otg-vbus {
compatible = "regulator-fixed";
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
&clks {
assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
<&clks IMX6QDL_CLK_LDB_DI1_SEL>;
assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
<&clks IMX6QDL_CLK_PLL3_USB_OTG>;
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
status = "okay";
fixed-link {
speed = <1000>;
full-duplex;
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch@0 {
compatible = "marvell,mv88e6085";
reg = <0>;
mdio {
#address-cells = <1>;
#size-cells = <0>;
sw_phy0: ethernet-phy@0 {
reg = <0x0>;
};
sw_phy1: ethernet-phy@1 {
reg = <0x1>;
};
sw_phy2: ethernet-phy@2 {
reg = <0x2>;
};
sw_phy3: ethernet-phy@3 {
reg = <0x3>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
lan4: port@0 {
reg = <0>;
label = "lan4";
phy-handle = <&sw_phy0>;
phy-mode = "internal";
local-mac-address = [00 00 00 00 00 00];
};
lan3: port@1 {
reg = <1>;
label = "lan3";
phy-handle = <&sw_phy1>;
phy-mode = "internal";
local-mac-address = [00 00 00 00 00 00];
};
lan2: port@2 {
reg = <2>;
label = "lan2";
phy-handle = <&sw_phy2>;
phy-mode = "internal";
local-mac-address = [00 00 00 00 00 00];
};
lan1: port@3 {
reg = <3>;
label = "lan1";
phy-handle = <&sw_phy3>;
phy-mode = "internal";
local-mac-address = [00 00 00 00 00 00];
};
port@5 {
reg = <5>;
ethernet = <&fec>;
phy-mode = "rgmii-id";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
};
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
gsc: gsc@20 {
compatible = "gw,gsc";
reg = <0x20>;
interrupt-parent = <&gpio1>;
interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <1>;
#size-cells = <0>;
adc {
compatible = "gw,gsc-adc";
#address-cells = <1>;
#size-cells = <0>;
channel@0 {
gw,mode = <0>;
reg = <0x00>;
label = "temp";
};
channel@2 {
gw,mode = <1>;
reg = <0x02>;
label = "vdd_vin";
};
channel@5 {
gw,mode = <1>;
reg = <0x05>;
label = "vdd_3p3";
};
channel@8 {
gw,mode = <1>;
reg = <0x08>;
label = "vdd_bat";
};
channel@b {
gw,mode = <1>;
reg = <0x0b>;
label = "vdd_5p0";
};
channel@e {
gw,mode = <1>;
reg = <0xe>;
label = "vdd_arm";
};
channel@11 {
gw,mode = <1>;
reg = <0x11>;
label = "vdd_soc";
};
channel@14 {
gw,mode = <1>;
reg = <0x14>;
label = "vdd_3p0";
};
channel@17 {
gw,mode = <1>;
reg = <0x17>;
label = "vdd_1p5";
};
channel@1d {
gw,mode = <1>;
reg = <0x1d>;
label = "vdd_1p8";
};
channel@20 {
gw,mode = <1>;
reg = <0x20>;
label = "vdd_an1";
};
channel@23 {
gw,mode = <1>;
reg = <0x23>;
label = "vdd_2p5";
};
};
};
gsc_gpio: gpio@23 {
compatible = "nxp,pca9555";
reg = <0x23>;
gpio-controller;
#gpio-cells = <2>;
interrupt-parent = <&gsc>;
interrupts = <4>;
};
eeprom1: eeprom@50 {
compatible = "atmel,24c02";
reg = <0x50>;
pagesize = <16>;
};
eeprom2: eeprom@51 {
compatible = "atmel,24c02";
reg = <0x51>;
pagesize = <16>;
};
eeprom3: eeprom@52 {
compatible = "atmel,24c02";
reg = <0x52>;
pagesize = <16>;
};
eeprom4: eeprom@53 {
compatible = "atmel,24c02";
reg = <0x53>;
pagesize = <16>;
};
dts1672: rtc@68 {
compatible = "dallas,ds1672";
reg = <0x68>;
};
};
&i2c2 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
magn@1c {
compatible = "st,lsm9ds1-magn";
reg = <0x1c>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mag>;
interrupt-parent = <&gpio5>;
interrupts = <17 IRQ_TYPE_EDGE_RISING>;
};
ltc3676: pmic@3c {
compatible = "lltc,ltc3676";
reg = <0x3c>;
interrupt-parent = <&gpio1>;
interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
regulators {
/* VDD_SOC (1+R1/R2 = 1.635) */
reg_vdd_soc: sw1 {
regulator-name = "vddsoc";
regulator-min-microvolt = <674400>;
regulator-max-microvolt = <1308000>;
lltc,fb-voltage-divider = <127000 200000>;
regulator-ramp-delay = <7000>;
regulator-boot-on;
regulator-always-on;
};
/* VDD_1P8 (1+R1/R2 = 2.505): GbE switch */
reg_1p8v: sw2 {
regulator-name = "vdd1p8";
regulator-min-microvolt = <1033310>;
regulator-max-microvolt = <2004000>;
lltc,fb-voltage-divider = <301000 200000>;
regulator-ramp-delay = <7000>;
regulator-boot-on;
regulator-always-on;
};
/* VDD_ARM (1+R1/R2 = 1.635) */
reg_vdd_arm: sw3 {
regulator-name = "vddarm";
regulator-min-microvolt = <674400>;
regulator-max-microvolt = <1308000>;
lltc,fb-voltage-divider = <127000 200000>;
regulator-ramp-delay = <7000>;
regulator-boot-on;
regulator-always-on;
};
/* VDD_DDR (1+R1/R2 = 2.105) */
reg_vdd_ddr: sw4 {
regulator-name = "vddddr";
regulator-min-microvolt = <868310>;
regulator-max-microvolt = <1684000>;
lltc,fb-voltage-divider = <221000 200000>;
regulator-ramp-delay = <7000>;
regulator-boot-on;
regulator-always-on;
};
/* VDD_2P5 (1+R1/R2 = 3.435): PCIe/ENET-PHY */
reg_2p5v: ldo2 {
regulator-name = "vdd2p5";
regulator-min-microvolt = <2490375>;
regulator-max-microvolt = <2490375>;
lltc,fb-voltage-divider = <487000 200000>;
regulator-boot-on;
regulator-always-on;
};
/* VDD_HIGH (1+R1/R2 = 4.17) */
reg_3p0v: ldo4 {
regulator-name = "vdd3p0";
regulator-min-microvolt = <3023250>;
regulator-max-microvolt = <3023250>;
lltc,fb-voltage-divider = <634000 200000>;
regulator-boot-on;
regulator-always-on;
};
};
};
crypto@60 {
compatible = "atmel,atecc508a";
reg = <0x60>;
};
imu@6a {
compatible = "st,lsm9ds1-imu";
reg = <0x6a>;
st,drdy-int-pin = <1>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_imu>;
interrupt-parent = <&gpio4>;
interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
};
};
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
egalax_ts: touchscreen@4 {
compatible = "eeti,egalax_ts";
reg = <0x04>;
interrupt-parent = <&gpio1>;
interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
wakeup-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
};
};
&ldb {
status = "okay";
lvds-channel@0 {
fsl,data-mapping = "spwg";
fsl,data-width = <18>;
status = "okay";
display-timings {
native-mode = <&timing0>;
timing0: timing-hsd100pxn1 {
clock-frequency = <65000000>;
hactive = <1024>;
vactive = <768>;
hback-porch = <220>;
hfront-porch = <40>;
vback-porch = <21>;
vfront-porch = <7>;
hsync-len = <60>;
vsync-len = <10>;
};
};
};
};
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie>;
reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
status = "okay";
};
&pwm2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
status = "disabled";
};
&pwm3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
status = "disabled";
};
&pwm4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm4>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
uart-has-rtscts;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
uart-has-rtscts;
status = "okay";
};
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
status = "okay";
};
&usbotg {
vbus-supply = <®_usb_otg_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
status = "okay";
};
&usbh1 {
vbus-supply = <®_usb_h1_vbus>;
status = "okay";
};
&usdhc3 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc3>;
pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
non-removable;
vmmc-supply = <®_3p3v>;
keep-power-in-suspend;
status = "okay";
};
&wdog1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wdog>;
fsl,ext-reset-output;
};
&iomuxc {
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x4001b0b0 /* PHY_RST# */
>;
};
pinctrl_gpio_leds: gpioledsgrp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0
MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x0001b0b0 /* GSC_IRQ# */
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
>;
};
pinctrl_imu: imugrp {
fsl,pins = <
MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
>;
};
pinctrl_mag: maggrp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b0
>;
};
pinctrl_pcie: pciegrp {
fsl,pins = <
MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 /* PCIE RST */
>;
};
pinctrl_pmic: pmicgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 /* PMIC_IRQ# */
>;
};
pinctrl_pps: ppsgrp {
fsl,pins = <
MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
>;
};
pinctrl_pwm2: pwm2grp {
fsl,pins = <
MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1
>;
};
pinctrl_pwm3: pwm3grp {
fsl,pins = <
MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
>;
};
pinctrl_pwm4: pwm4grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
pinctrl_uart2: uart2grp {
fsl,pins = <
MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
>;
};
pinctrl_uart3: uart3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
>;
};
pinctrl_uart5: uart5grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* PWR_EN */
MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0 /* OC */
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
MX6QDL_PAD_SD3_RST__SD3_RESET 0x10059
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
>;
};
pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9
MX6QDL_PAD_SD3_RST__SD3_RESET 0x100b9
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9
MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170b9
MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170b9
MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170b9
MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170b9
>;
};
pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9
MX6QDL_PAD_SD3_RST__SD3_RESET 0x100f9
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170f9
MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170f9
MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170f9
MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170f9
>;
};
pinctrl_wdog: wdoggrp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x1b0b0
>;
};
};
