Spracherkennung für: .dts vermutete Sprache: Unknown {[0] [0] [0]} [Methode: Schwerpunktbildung, einfache Gewichte, sechs Dimensionen]
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
* Copyright (C) Protonic Holland
* Author: David Jander <david@protonic.nl>
*/
/dts-v1/;
#include "stm32mp151a-prtt1l.dtsi"
/ {
model = "Protonic PRTT1C";
compatible = "prt,prtt1c", "st,stm32mp151";
clock_ksz9031: clock-ksz9031 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
clock_sja1105: clock-sja1105 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
pse_t1l1: ethernet-pse-1 {
compatible = "podl-pse-regulator";
pse-supply = <®_t1l1>;
#pse-cells = <0>;
};
pse_t1l2: ethernet-pse-2 {
compatible = "podl-pse-regulator";
pse-supply = <®_t1l2>;
#pse-cells = <0>;
};
mdio0: mdio {
compatible = "virtual,mdio-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpios = <&gpioc 1 GPIO_ACTIVE_HIGH
&gpioa 2 GPIO_ACTIVE_HIGH>;
};
reg_t1l1: regulator-pse-t1l1 {
compatible = "regulator-fixed";
regulator-name = "pse-t1l1";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
gpio = <&gpiog 13 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_t1l2: regulator-pse-t1l2 {
compatible = "regulator-fixed";
regulator-name = "pse-t1l2";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
gpio = <&gpiog 14 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpiod 8 GPIO_ACTIVE_LOW>;
};
};
ðernet0 {
fixed-link {
speed = <100>;
full-duplex;
};
};
&gpioa {
gpio-line-names =
"", "", "", "PHY0_nRESET", "PHY0_nINT", "", "", "",
"", "", "", "", "", "", "", "SPI1_nSS";
};
&gpiod {
gpio-line-names =
"", "", "", "", "", "", "", "",
"WFM_RESET", "", "", "", "", "", "", "";
};
&gpioe {
gpio-line-names =
"SDMMC2_nRESET", "", "", "", "", "", "SPI1_nRESET", "",
"", "", "", "", "WFM_nIRQ", "", "", "";
};
&gpiog {
gpio-line-names =
"", "", "", "", "", "", "", "PHY3_nINT",
"PHY1_nINT", "PHY3_nRESET", "PHY2_nINT", "PHY2_nRESET",
"PHY1_nRESET", "SPE1_PWR", "SPE0_PWR", "";
};
&mdio0 {
/* All this DP83TD510E PHYs can't be probed before switch@0 is
* probed so we need to use compatible with PHYid
*/
/* TI DP83TD510E */
t1l0_phy: ethernet-phy@6 {
compatible = "ethernet-phy-id2000.0181";
reg = <6>;
interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
reset-assert-us = <10>;
reset-deassert-us = <35>;
};
/* TI DP83TD510E */
t1l1_phy: ethernet-phy@7 {
compatible = "ethernet-phy-id2000.0181";
reg = <7>;
interrupts-extended = <&gpiog 8 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpiog 12 GPIO_ACTIVE_LOW>;
reset-assert-us = <10>;
reset-deassert-us = <35>;
pses = <&pse_t1l1>;
};
/* TI DP83TD510E */
t1l2_phy: ethernet-phy@10 {
compatible = "ethernet-phy-id2000.0181";
reg = <10>;
interrupts-extended = <&gpiog 10 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpiog 11 GPIO_ACTIVE_LOW>;
reset-assert-us = <10>;
reset-deassert-us = <35>;
pses = <&pse_t1l2>;
};
/* Micrel KSZ9031 */
rj45_phy: ethernet-phy@2 {
reg = <2>;
interrupts-extended = <&gpiog 7 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <1000>;
clocks = <&clock_ksz9031>;
};
};
&qspi {
status = "disabled";
};
&sdmmc2 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
non-removable;
no-sd;
no-sdio;
no-1-8-v;
st,neg-edge;
bus-width = <8>;
vmmc-supply = <®_3v3>;
vqmmc-supply = <®_3v3>;
status = "okay";
};
&{sdmmc2_b4_od_pins_a/pins1} {
pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
<STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
<STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
<STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
};
&{sdmmc2_b4_pins_a/pins1} {
pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
<STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
<STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
<STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
<STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
};
&{sdmmc2_b4_sleep_pins_a/pins} {
pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
<STM32_PINMUX('B', 7, ANALOG)>, /* SDMMC2_D1 */
<STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
<STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
<STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
<STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
};
&{sdmmc2_d47_pins_a/pins} {
pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
<STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
<STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
<STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
};
&{sdmmc2_d47_sleep_pins_a/pins} {
pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
<STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
<STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
<STM32_PINMUX('D', 3, ANALOG)>; /* SDMMC2_D7 */
};
&sdmmc3 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc3_b4_pins_b>;
pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
non-removable;
no-1-8-v;
st,neg-edge;
bus-width = <4>;
vmmc-supply = <®_3v3>;
vqmmc-supply = <®_3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
mmc@1 {
compatible = "prt,prtt1c-wfm200", "silabs,wf200";
reg = <1>;
};
};
&{sdmmc3_b4_od_pins_b/pins1} {
pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
<STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
<STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
<STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
};
&{sdmmc3_b4_pins_b/pins1} {
pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
<STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
<STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
<STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
<STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
};
&{sdmmc3_b4_sleep_pins_b/pins} {
pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* SDMMC3_D0 */
<STM32_PINMUX('D', 4, ANALOG)>, /* SDMMC3_D1 */
<STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
<STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
<STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
<STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
};
&spi1 {
pinctrl-0 = <&spi1_pins_b>;
pinctrl-names = "default";
cs-gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
switch@0 {
compatible = "nxp,sja1105q";
reg = <0>;
spi-max-frequency = <4000000>;
spi-rx-delay-us = <1>;
spi-tx-delay-us = <1>;
spi-cpha;
reset-gpios = <&gpioe 6 GPIO_ACTIVE_LOW>;
clocks = <&clock_sja1105>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "t1l0";
phy-mode = "rmii";
phy-handle = <&t1l0_phy>;
};
port@1 {
reg = <1>;
label = "t1l1";
phy-mode = "rmii";
phy-handle = <&t1l1_phy>;
};
port@2 {
reg = <2>;
label = "t1l2";
phy-mode = "rmii";
phy-handle = <&t1l2_phy>;
};
port@3 {
reg = <3>;
label = "rj45";
phy-handle = <&rj45_phy>;
phy-mode = "rgmii-id";
};
port@4 {
reg = <4>;
label = "cpu";
ethernet = <ðernet0>;
phy-mode = "rmii";
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};
};
