// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
// Copyright (c) 2016 ARM Ltd.
/dts-v1/;
#include "sun50i-a64.dtsi"
#include "sun50i-a64-cpu-opp.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "BananaPi-M64";
compatible = "sinovoip,bananapi-m64", "allwinner,sun50i-a64";
aliases {
ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
};
chosen {
stdout-path = "serial0:115200n8";
};
hdmi-connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
leds {
compatible = "gpio-leds";
led-0 {
label = "bananapi-m64:red:pwr";
gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
default-state = "on";
};
led-1 {
label = "bananapi-m64:green:user";
gpios = <&pio 4 14 GPIO_ACTIVE_HIGH>; /* PE14 */
};
led-2 {
label = "bananapi-m64:blue:user";
gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
};
};
wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
clock-names = "ext_clock";
};
};
&codec {
status = "okay";
};
&codec_analog {
cpvdd-supply = <®_eldo1>;
status = "okay";
};
&cpu0 {
cpu-supply = <®_dcdc2>;
};
&cpu1 {
cpu-supply = <®_dcdc2>;
};
&cpu2 {
cpu-supply = <®_dcdc2>;
};
&cpu3 {
cpu-supply = <®_dcdc2>;
};
&dai {
status = "okay";
};
&de {
status = "okay";
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii-id";
phy-handle = <&ext_rgmii_phy>;
phy-supply = <®_dc1sw>;
status = "okay";
};
&hdmi {
hvcc-supply = <®_dldo1>;
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&i2c1 {
status = "okay";
};
&i2c1_pins {
bias-pull-up;
};
&mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_dcdc1>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
disable-wp;
bus-width = <4>;
status = "okay";
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
vmmc-supply = <®_dldo2>;
vqmmc-supply = <®_dldo4>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&r_pio>;
interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
interrupt-names = "host-wake";
};
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&r_rsb {
status = "okay";
axp803: pmic@3a3 {
compatible = "x-powers,axp803";
reg = <0x3a3>;
interrupt-parent = <&r_intc>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
};
};
#include "axp803.dtsi"
&ac_power_supply {
status = "okay";
};
&battery_power_supply {
status = "okay";
};
®_aldo1 {
/*
* This regulator also drives the PE pingroup GPIOs,
* which also controls two LEDs.
*/
regulator-always-on;
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-name = "afvcc-csi";
};
®_aldo2 {
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-pl";
};
®_aldo3 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-pll-avcc";
};
®_dc1sw {
/*
* This regulator also indirectly drives the PD pingroup GPIOs,
* which also controls the power LED.
*/
regulator-always-on;
regulator-name = "vcc-phy";
};
®_dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-3v3";
};
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1040000>;
regulator-max-microvolt = <1300000>;
regulator-name = "vdd-cpux";
};
/* DCDC3 is polyphased with DCDC2 */
®_dcdc5 {
regulator-always-on;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-name = "vcc-dram";
};
®_dcdc6 {
regulator-always-on;
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-sys";
};
®_dldo1 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-hdmi-dsi";
};
®_dldo2 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};
®_dldo4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi-io";
};
®_drivevbus {
regulator-name = "usb0-vbus";
status = "okay";
};
®_eldo1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "cpvdd";
};
®_fldo1 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "vcc-1v2-hsic";
};
/*
* The A64 chip cannot work without this regulator off, although
* it seems to be only driving the AR100 core.
* Maybe we don't still know well about CPUs domain.
*/
®_fldo2 {
regulator-always-on;
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpus";
};
®_rtc_ldo {
regulator-name = "vcc-rtc";
};
&simplefb_hdmi {
vcc-hdmi-supply = <®_dldo1>;
};
&sound {
status = "okay";
simple-audio-card,widgets = "Headphone", "Headphone Jack",
"Microphone", "Microphone Jack",
"Microphone", "Onboard Microphone";
simple-audio-card,routing =
"Left DAC", "DACL",
"Right DAC", "DACR",
"ADCL", "Left ADC",
"ADCR", "Right ADC",
"Headphone Jack", "HP",
"MIC2", "Microphone Jack",
"Onboard Microphone", "MBIAS",
"MIC1", "Onboard Microphone";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
uart-has-rtscts;
status = "okay";
bluetooth {
compatible = "brcm,bcm43438-bt";
clocks = <&rtc CLK_OSC32K_FANOUT>;
clock-names = "lpo";
vbat-supply = <®_dldo2>;
vddio-supply = <®_dldo4>;
device-wakeup-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
host-wakeup-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
shutdown-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
};
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usb_power_supply {
status = "okay";
};
&usbphy {
usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <®_drivevbus>;
status = "okay";
};
[ Dauer der Verarbeitung: 0.12 Sekunden
(vorverarbeitet)
]
