Spracherkennung für: .dtsi vermutete Sprache: Unknown {[0] [0] [0]} [Methode: Schwerpunktbildung, einfache Gewichte, sechs Dimensionen]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
// Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
// Copyright (C) 2020 Martijn Braam <martijn@brixit.nl>
// Copyright (C) 2020 Ondrej Jirman <megous@megous.com>
#include "sun50i-a64.dtsi"
#include "sun50i-a64-cpu-opp.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pwm/pwm.h>
/ {
chassis-type = "handset";
aliases {
ethernet0 = &rtl8723cs;
serial0 = &uart0;
};
backlight: backlight {
compatible = "pwm-backlight";
pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>;
enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
power-supply = <®_ps>;
/* Backlight configuration differs per PinePhone revision. */
};
bt_sco_codec: bt-sco-codec {
#sound-dai-cells = <1>;
compatible = "linux,bt-sco";
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
led0: led-0 {
function = LED_FUNCTION_INDICATOR;
color = <LED_COLOR_ID_BLUE>;
gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
retain-state-suspended;
};
led1: led-1 {
function = LED_FUNCTION_INDICATOR;
color = <LED_COLOR_ID_GREEN>;
gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */
retain-state-suspended;
};
led2: led-2 {
function = LED_FUNCTION_INDICATOR;
color = <LED_COLOR_ID_RED>;
gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
retain-state-suspended;
};
};
multi-led {
compatible = "leds-group-multicolor";
color = <LED_COLOR_ID_RGB>;
function = LED_FUNCTION_INDICATOR;
leds = <&led0>, <&led1>, <&led2>;
};
reg_ps: ps-regulator {
compatible = "regulator-fixed";
regulator-name = "ps";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-boot-on;
};
reg_vbat_wifi: vbat-wifi {
compatible = "regulator-fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vbat-wifi";
};
sgm3140: led-controller {
compatible = "sgmicro,sgm3140";
vin-supply = <®_dcdc1>;
sgm3140_flash: led {
function = LED_FUNCTION_FLASH;
color = <LED_COLOR_ID_WHITE>;
flash-max-timeout-us = <250000>;
};
};
speaker_amp: audio-amplifier {
compatible = "simple-audio-amplifier";
enable-gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */
sound-name-prefix = "Speaker Amp";
};
vibrator {
compatible = "gpio-vibrator";
enable-gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
vcc-supply = <®_dcdc1>;
};
};
&codec {
pinctrl-names = "default";
pinctrl-0 = <&aif3_pins>;
status = "okay";
};
&codec_analog {
cpvdd-supply = <®_eldo1>;
status = "okay";
};
&cpu0 {
cpu-supply = <®_dcdc2>;
};
&cpu1 {
cpu-supply = <®_dcdc2>;
};
&cpu2 {
cpu-supply = <®_dcdc2>;
};
&cpu3 {
cpu-supply = <®_dcdc2>;
};
&dai {
status = "okay";
};
&de {
status = "okay";
};
&dphy {
status = "okay";
};
&dsi {
vcc-dsi-supply = <®_dldo1>;
status = "okay";
panel@0 {
compatible = "xingbangda,xbd599";
reg = <0>;
reset-gpios = <&pio 3 23 GPIO_ACTIVE_LOW>; /* PD23 */
iovcc-supply = <®_dldo2>;
vcc-supply = <®_ldo_io0>;
backlight = <&backlight>;
};
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&i2c0 {
status = "okay";
touchscreen@5d {
compatible = "goodix,gt917s";
reg = <0x5d>;
interrupt-parent = <&pio>;
interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
reset-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
AVDD28-supply = <®_ldo_io0>;
VDDIO-supply = <®_ldo_io0>;
touchscreen-size-x = <720>;
touchscreen-size-y = <1440>;
};
};
&i2c1 {
status = "okay";
/* Alternative magnetometer */
af8133j: magnetometer@1c {
compatible = "voltafield,af8133j";
reg = <0x1c>;
reset-gpios = <&pio 1 1 GPIO_ACTIVE_LOW>;
avdd-supply = <®_dldo1>;
dvdd-supply = <®_dldo1>;
mount-matrix = "0", "-1", "0",
"-1", "0", "0",
"0", "0", "-1";
/* status will be fixed up in firmware */
status = "disabled";
};
/* Magnetometer */
lis3mdl: magnetometer@1e {
compatible = "st,lis3mdl-magn";
reg = <0x1e>;
vdd-supply = <®_dldo1>;
vddio-supply = <®_dldo1>;
mount-matrix = "0", "1", "0",
"-1", "0", "0",
"0", "0", "1";
};
/* Light/proximity sensor */
light-sensor@48 {
compatible = "sensortek,stk3311";
reg = <0x48>;
interrupt-parent = <&pio>;
interrupts = <1 0 IRQ_TYPE_EDGE_FALLING>; /* PB0 */
};
/* Accelerometer/gyroscope */
accelerometer@68 {
compatible = "invensense,mpu6050";
reg = <0x68>;
interrupt-parent = <&pio>;
interrupts = <7 5 IRQ_TYPE_EDGE_RISING>; /* PH5 */
vdd-supply = <®_dldo1>;
vddio-supply = <®_dldo1>;
mount-matrix = "0", "1", "0",
"-1", "0", "0",
"0", "0", "1";
};
};
/* Connected to pogo pins (external spring based pinheader for user addons) */
&i2c2 {
status = "okay";
};
&lradc {
vref-supply = <®_aldo3>;
wakeup-source;
status = "okay";
button-200 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <200000>;
};
button-400 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <400000>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_dcdc1>;
vqmmc-supply = <®_dcdc1>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
disable-wp;
bus-width = <4>;
status = "okay";
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
vmmc-supply = <®_vbat_wifi>;
vqmmc-supply = <®_dldo4>;
bus-width = <4>;
non-removable;
status = "okay";
rtl8723cs: wifi@1 {
reg = <1>;
};
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <®_dcdc1>;
vqmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&pio {
vcc-pb-supply = <®_dcdc1>;
vcc-pc-supply = <®_dcdc1>;
vcc-pd-supply = <®_dcdc1>;
vcc-pe-supply = <®_aldo1>;
vcc-pf-supply = <®_dcdc1>;
vcc-pg-supply = <®_dldo4>;
vcc-ph-supply = <®_dcdc1>;
};
&r_pio {
/*
* FIXME: We can't add that supply for now since it would
* create a circular dependency between pinctrl, the regulator
* and the RSB Bus.
*
* vcc-pl-supply = <®_aldo2>;
*/
};
&r_pwm {
status = "okay";
};
&r_rsb {
status = "okay";
axp803: pmic@3a3 {
compatible = "x-powers,axp803";
reg = <0x3a3>;
interrupt-parent = <&r_intc>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
};
};
#include "axp803.dtsi"
&battery_power_supply {
status = "okay";
};
®_aldo1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "dovdd-csi";
};
®_aldo2 {
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-pl";
};
®_aldo3 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-pll-avcc";
};
®_dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-3v3";
};
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1300000>;
regulator-name = "vdd-cpux";
};
/* DCDC3 is polyphased with DCDC2 */
®_dcdc5 {
regulator-always-on;
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "vcc-dram";
};
®_dcdc6 {
regulator-always-on;
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-sys";
};
®_dldo1 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-dsi-sensor";
};
®_dldo2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-mipi-io";
};
®_dldo3 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-name = "avdd-csi";
};
®_dldo4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-wifi-io";
};
®_eldo1 {
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-lpddr";
};
®_eldo3 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "dvdd-1v8-csi";
};
®_fldo1 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "vcc-1v2-hsic";
};
®_fldo2 {
regulator-always-on;
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpus";
};
®_ldo_io0 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-lcd-ctp-stk";
status = "okay";
};
®_ldo_io1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-1v8-typec";
status = "okay";
};
®_rtc_ldo {
regulator-name = "vcc-rtc";
};
&sound {
status = "okay";
simple-audio-card,name = "PinePhone";
simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
simple-audio-card,widgets = "Microphone", "Headset Microphone",
"Microphone", "Internal Microphone",
"Headphone", "Headphone Jack",
"Speaker", "Internal Earpiece",
"Speaker", "Internal Speaker";
simple-audio-card,routing =
"Headphone Jack", "HP",
"Internal Earpiece", "EARPIECE",
"Internal Speaker", "Speaker Amp OUTL",
"Internal Speaker", "Speaker Amp OUTR",
"Speaker Amp INL", "LINEOUT",
"Speaker Amp INR", "LINEOUT",
"Left DAC", "DACL",
"Right DAC", "DACR",
"ADCL", "Left ADC",
"ADCR", "Right ADC",
"Internal Microphone", "MBIAS",
"MIC1", "Internal Microphone",
"Headset Microphone", "HBIAS",
"MIC2", "Headset Microphone";
simple-audio-card,dai-link@2 {
format = "dsp_a";
frame-master = <&link2_codec>;
bitclock-master = <&link2_codec>;
bitclock-inversion;
link2_cpu: cpu {
sound-dai = <&bt_sco_codec 0>;
};
link2_codec: codec {
sound-dai = <&codec 2>;
dai-tdm-slot-num = <1>;
dai-tdm-slot-width = <32>;
};
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
status = "okay";
bluetooth {
compatible = "realtek,rtl8723cs-bt";
device-wake-gpios = <&pio 7 6 GPIO_ACTIVE_LOW>; /* PH6 */
enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
host-wake-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
};
};
/* Connected to the modem (hardware flow control can't be used) */
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
status = "okay";
};
&usb_otg {
dr_mode = "peripheral";
status = "okay";
};
&usb_power_supply {
status = "okay";
};
&usbphy {
status = "okay";
};
