Quelle  pm8150b.dtsi   Sprache: unbekannt

// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
 * Copyright (c) 2019, Linaro Limited
 */

#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>

/ {
 thermal-zones {
  pm8150b-thermal {
   polling-delay-passive = <100>;

   thermal-sensors = <&pm8150b_temp>;

   trips {
    trip0 {
     temperature = <95000>;
     hysteresis = <0>;
     type = "passive";
    };

    trip1 {
     temperature = <115000>;
     hysteresis = <0>;
     type = "hot";
    };

    trip2 {
     temperature = <145000>;
     hysteresis = <0>;
     type = "critical";
    };
   };
  };
 };
};

&spmi_bus {
 pmic@2 {
  compatible = "qcom,pm8150b", "qcom,spmi-pmic";
  reg = <0x2 SPMI_USID>;
  #address-cells = <1>;
  #size-cells = <0>;

  pon@800 {
   compatible = "qcom,pm8916-pon";
   reg = <0x0800>;

   status = "disabled";
  };

  pm8150b_vbus: usb-vbus-regulator@1100 {
   compatible = "qcom,pm8150b-vbus-reg";
   status = "disabled";
   reg = <0x1100>;
  };

  pm8150b_typec: typec@1500 {
   compatible = "qcom,pm8150b-typec";
   status = "disabled";
   reg = <0x1500>,
         <0x1700>;
   interrupts = <0x2 0x15 0x00 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x15 0x01 IRQ_TYPE_EDGE_BOTH>,
         <0x2 0x15 0x02 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x15 0x03 IRQ_TYPE_EDGE_BOTH>,
         <0x2 0x15 0x04 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x15 0x05 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x15 0x06 IRQ_TYPE_EDGE_BOTH>,
         <0x2 0x15 0x07 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x17 0x00 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x17 0x01 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x17 0x02 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x17 0x03 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x17 0x04 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x17 0x05 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x17 0x06 IRQ_TYPE_EDGE_RISING>,
         <0x2 0x17 0x07 IRQ_TYPE_EDGE_RISING>;
   interrupt-names = "or-rid-detect-change",
       "vpd-detect",
       "cc-state-change",
       "vconn-oc",
       "vbus-change",
       "attach-detach",
       "legacy-cable-detect",
       "try-snk-src-detect",
       "sig-tx",
       "sig-rx",
       "msg-tx",
       "msg-rx",
       "msg-tx-failed",
       "msg-tx-discarded",
       "msg-rx-discarded",
       "fr-swap";
   vdd-vbus-supply = <&pm8150b_vbus>;
  };

  pm8150b_temp: temp-alarm@2400 {
   compatible = "qcom,spmi-temp-alarm";
   reg = <0x2400>;
   interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
   io-channels = <&pm8150b_adc ADC5_DIE_TEMP>;
   io-channel-names = "thermal";
   #thermal-sensor-cells = <0>;
  };

  pm8150b_adc: adc@3100 {
   compatible = "qcom,spmi-adc5";
   reg = <0x3100>;
   #address-cells = <1>;
   #size-cells = <0>;
   #io-channel-cells = <1>;
   interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;

   channel@0 {
    reg = <ADC5_REF_GND>;
    qcom,pre-scaling = <1 1>;
    label = "ref_gnd";
   };

   channel@1 {
    reg = <ADC5_1P25VREF>;
    qcom,pre-scaling = <1 1>;
    label = "vref_1p25";
   };

   channel@6 {
    reg = <ADC5_DIE_TEMP>;
    qcom,pre-scaling = <1 1>;
    label = "die_temp";
   };

   channel@9 {
    reg = <ADC5_CHG_TEMP>;
    qcom,pre-scaling = <1 1>;
    label = "chg_temp";
   };
  };

  pm8150b_adc_tm: adc-tm@3500 {
   compatible = "qcom,spmi-adc-tm5";
   reg = <0x3500>;
   interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
   #thermal-sensor-cells = <1>;
   #address-cells = <1>;
   #size-cells = <0>;
   status = "disabled";
  };

  pm8150b_gpios: gpio@c000 {
   compatible = "qcom,pm8150b-gpio", "qcom,spmi-gpio";
   reg = <0xc000>;
   gpio-controller;
   gpio-ranges = <&pm8150b_gpios 0 0 12>;
   #gpio-cells = <2>;
   interrupt-controller;
   #interrupt-cells = <2>;
  };
 };

 pmic@3 {
  compatible = "qcom,pm8150b", "qcom,spmi-pmic";
  reg = <0x3 SPMI_USID>;
  #address-cells = <1>;
  #size-cells = <0>;

  pm8150b_lpg: pwm {
   compatible = "qcom,pm8150b-lpg";

   #address-cells = <1>;
   #size-cells = <0>;
   #pwm-cells = <2>;

   status = "disabled";
  };
 };
};