Quelle  pm8916.dtsi   Sprache: unbekannt

// SPDX-License-Identifier: GPL-2.0
#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>

/ {
 thermal-zones {
  pm8916-thermal {
   polling-delay-passive = <100>;

   thermal-sensors = <&pm8916_temp>;

   trips {
    trip0 {
     temperature = <105000>;
     hysteresis = <0>;
     type = "passive";
    };

    trip1 {
     temperature = <125000>;
     hysteresis = <0>;
     type = "hot";
    };

    trip2 {
     temperature = <145000>;
     hysteresis = <0>;
     type = "critical";
    };
   };
  };
 };
};

&spmi_bus {
 pm8916_0: pmic@0 {
  compatible = "qcom,pm8916", "qcom,spmi-pmic";
  reg = <0x0 SPMI_USID>;
  #address-cells = <1>;
  #size-cells = <0>;

  pon@800 {
   compatible = "qcom,pm8916-pon";
   reg = <0x800>;
   mode-bootloader = <0x2>;
   mode-recovery = <0x1>;

   pwrkey {
    compatible = "qcom,pm8941-pwrkey";
    interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
    debounce = <15625>;
    bias-pull-up;
    linux,code = <KEY_POWER>;
   };

   pm8916_resin: resin {
    compatible = "qcom,pm8941-resin";
    interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
    debounce = <15625>;
    bias-pull-up;
    status = "disabled";
   };

   watchdog {
    compatible = "qcom,pm8916-wdt";
    interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>;
    timeout-sec = <60>;
   };
  };

  pm8916_charger: charger@1000 {
   compatible = "qcom,pm8916-lbc";
   reg = <0x1000>, <0x1200>, <0x1300>, <0x1600>;
   reg-names = "chgr", "bat_if", "usb", "misc";

   interrupts = <0x0 0x10 0 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x10 6 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x13 0 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x13 4 IRQ_TYPE_EDGE_BOTH>;
   interrupt-names = "vbat_det",
       "fast_chg",
       "chg_fail",
       "chg_done",
       "bat_pres",
       "temp_ok",
       "coarse_det",
       "usb_vbus",
       "chg_gone",
       "overtemp";

   status = "disabled";
  };

  pm8916_usbin: usb-detect@1300 {
   compatible = "qcom,pm8941-misc";
   reg = <0x1300>;
   interrupts = <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>;
   interrupt-names = "usb_vbus";
   status = "disabled";
  };

  pm8916_temp: temp-alarm@2400 {
   compatible = "qcom,spmi-temp-alarm";
   reg = <0x2400>;
   interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
   io-channels = <&pm8916_vadc VADC_DIE_TEMP>;
   io-channel-names = "thermal";
   #thermal-sensor-cells = <0>;
  };

  pm8916_vadc: adc@3100 {
   compatible = "qcom,spmi-vadc";
   reg = <0x3100>;
   interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
   #address-cells = <1>;
   #size-cells = <0>;
   #io-channel-cells = <1>;

   channel@0 {
    reg = <VADC_USBIN>;
    qcom,pre-scaling = <1 10>;
   };
   channel@7 {
    reg = <VADC_VSYS>;
    qcom,pre-scaling = <1 3>;
   };
   channel@8 {
    reg = <VADC_DIE_TEMP>;
   };
   channel@9 {
    reg = <VADC_REF_625MV>;
   };
   channel@a {
    reg = <VADC_REF_1250MV>;
   };
   channel@e {
    reg = <VADC_GND_REF>;
   };
   channel@f {
    reg = <VADC_VDD_VADC>;
   };
  };

  pm8916_bms: battery@4000 {
   compatible = "qcom,pm8916-bms-vm";
   reg = <0x4000>;
   interrupts = <0x0 0x40 0 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x40 1 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x40 2 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x40 3 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x40 4 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x40 5 IRQ_TYPE_EDGE_RISING>;
   interrupt-names = "cv_leave",
       "cv_enter",
       "ocv_good",
       "ocv_thr",
       "fifo",
       "state_chg";

   status = "disabled";
  };

  rtc@6000 {
   compatible = "qcom,pm8941-rtc";
   reg = <0x6000>, <0x6100>;
   reg-names = "rtc", "alarm";
   interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
  };

  pm8916_mpps: mpps@a000 {
   compatible = "qcom,pm8916-mpp", "qcom,spmi-mpp";
   reg = <0xa000>;
   gpio-controller;
   #gpio-cells = <2>;
   gpio-ranges = <&pm8916_mpps 0 0 4>;
   interrupt-controller;
   #interrupt-cells = <2>;
  };

  pm8916_gpios: gpio@c000 {
   compatible = "qcom,pm8916-gpio", "qcom,spmi-gpio";
   reg = <0xc000>;
   gpio-controller;
   gpio-ranges = <&pm8916_gpios 0 0 4>;
   #gpio-cells = <2>;
   interrupt-controller;
   #interrupt-cells = <2>;
  };
 };

 pm8916_1: pmic@1 {
  compatible = "qcom,pm8916", "qcom,spmi-pmic";
  reg = <0x1 SPMI_USID>;
  #address-cells = <1>;
  #size-cells = <0>;

  pm8916_pwm: pwm {
   compatible = "qcom,pm8916-pwm";

   #pwm-cells = <2>;

   status = "disabled";
  };

  pm8916_vib: vibrator@c000 {
   compatible = "qcom,pm8916-vib";
   reg = <0xc000>;
   status = "disabled";
  };

  pm8916_codec: audio-codec@f000 {
   compatible = "qcom,pm8916-wcd-analog-codec";
   reg = <0xf000>;
   interrupt-parent = <&spmi_bus>;
   interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
         <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
         <0x1 0xf0 0x2 IRQ_TYPE_NONE>,
         <0x1 0xf0 0x3 IRQ_TYPE_NONE>,
         <0x1 0xf0 0x4 IRQ_TYPE_NONE>,
         <0x1 0xf0 0x5 IRQ_TYPE_NONE>,
         <0x1 0xf0 0x6 IRQ_TYPE_NONE>,
         <0x1 0xf0 0x7 IRQ_TYPE_NONE>,
         <0x1 0xf1 0x0 IRQ_TYPE_NONE>,
         <0x1 0xf1 0x1 IRQ_TYPE_NONE>,
         <0x1 0xf1 0x2 IRQ_TYPE_NONE>,
         <0x1 0xf1 0x3 IRQ_TYPE_NONE>,
         <0x1 0xf1 0x4 IRQ_TYPE_NONE>,
         <0x1 0xf1 0x5 IRQ_TYPE_NONE>;
   interrupt-names = "cdc_spk_cnp_int",
       "cdc_spk_clip_int",
       "cdc_spk_ocp_int",
       "mbhc_ins_rem_det1",
       "mbhc_but_rel_det",
       "mbhc_but_press_det",
       "mbhc_ins_rem_det",
       "mbhc_switch_int",
       "cdc_ear_ocp_int",
       "cdc_hphr_ocp_int",
       "cdc_hphl_ocp_det",
       "cdc_ear_cnp_int",
       "cdc_hphr_cnp_int",
       "cdc_hphl_cnp_int";
   #sound-dai-cells = <1>;
   status = "disabled";
  };
 };
};