Spracherkennung für: .dts vermutete Sprache: Unknown {[0] [0] [0]} [Methode: Schwerpunktbildung, einfache Gewichte, sechs Dimensionen]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include <dt-bindings/soc/rockchip,vop2.h>
#include "rk3568.dtsi"
/ {
model = "Ariaboard Photonicat";
compatible = "ariaboard,photonicat", "rockchip,rk3568";
aliases {
ethernet0 = &gmac0;
ethernet1 = &gmac1;
mmc0 = &sdhci;
mmc1 = &sdmmc0;
mmc2 = &sdmmc1;
};
battery: battery {
compatible = "simple-battery";
device-chemistry = "lithium-ion";
charge-full-design-microamp-hours = <6800000>;
energy-full-design-microwatt-hours = <25000000>;
voltage-max-design-microvolt = <4200000>;
voltage-min-design-microvolt = <3400000>;
ocv-capacity-celsius = <25>;
ocv-capacity-table-0 = <4100000 100>, <4040000 90>,
<3980000 80>, <3920000 70>,
<3870000 60>, <3820000 50>,
<3790000 40>, <3770000 30>,
<3740000 20>, <3680000 10>,
<3450000 0>;
};
chosen: chosen {
stdout-path = "serial2:1500000n8";
};
hdmi_con: hdmi-con {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
vcc_1v8: regulator-vcc-1v8 {
compatible = "regulator-fixed";
regulator-name = "vcc_1v8";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&vcc3v3_sys>;
};
vcc_3v3: regulator-vcc-3v3 {
compatible = "regulator-fixed";
regulator-name = "vcc_3v3";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc3v3_sys>;
};
/* actually fed by vcc_syson, dependent
* on pi6c clock generator
*/
vcc3v3_pcie: regulator-vcc3v3-pcie {
compatible = "regulator-fixed";
regulator-name = "vcc3v3_pcie";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc3v3_pi6c>;
};
/* pi6c pcie clock generator */
vcc3v3_pi6c: regulator-vcc3v3-pi6c {
compatible = "regulator-fixed";
enable-active-high;
gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pcie_pwren_h>;
regulator-name = "vcc3v3_pi6c";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc_syson>;
};
vcc3v3_sd: regulator-vcc3v3-sd {
compatible = "regulator-fixed";
gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc0_pwren>;
regulator-boot-on;
regulator-name = "vcc3v3_sd";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc_3v3>;
};
vcc3v3_sys: regulator-vcc3v3-sys {
compatible = "regulator-fixed";
regulator-name = "vcc3v3_sys";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc_syson>;
};
vcc3v4_rf: regulator-vcc3v4-rf {
compatible = "regulator-fixed";
enable-active-high;
gpio = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&rf_pwr_en>;
regulator-name = "vcc3v4_rf";
regulator-min-microvolt = <3400000>;
regulator-max-microvolt = <3400000>;
vin-supply = <&vccin_5v>;
};
vcc5v0_usb30_otg0: regulator-vcc5v0-usb30-otg0 {
compatible = "regulator-fixed";
enable-active-high;
gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb_host_pwren_h>;
regulator-name = "vcc5v0_usb30_otg0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&vccin_5v>;
};
vccin_5v: regulator-vccin-5v {
compatible = "regulator-fixed";
regulator-name = "vccin_5v";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
vcc_sysin: regulator-vcc-sysin {
compatible = "regulator-fixed";
regulator-name = "vcc_sysin";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&vccin_5v>;
};
vcc_syson: regulator-vcc-syson {
compatible = "regulator-fixed";
regulator-name = "vcc_syson";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&vcc_sysin>;
};
vcca_1v8: regulator-vcca-1v8 {
compatible = "regulator-fixed";
regulator-name = "vcca_1v8";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&vcc3v3_sys>;
};
vdda_0v9: regulator-vdda-0v9 {
compatible = "regulator-fixed";
regulator-name = "vdda_0v9";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <900000>;
vin-supply = <&vcc3v3_sys>;
};
vdd_gpu: regulator-vdd-gpu {
compatible = "pwm-regulator";
pwms = <&pwm2 0 5000 1>;
pwm-supply = <&vcc_syson>;
regulator-name = "vdd_gpu";
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1350000>;
regulator-ramp-delay = <6001>;
regulator-settling-time-up-us = <250>;
};
vdd_logic: regulator-vdd-logic {
compatible = "pwm-regulator";
pwms = <&pwm1 0 5000 1>;
pwm-supply = <&vcc_syson>;
regulator-name = "vdd_logic";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1350000>;
regulator-ramp-delay = <6001>;
regulator-settling-time-up-us = <250>;
};
rfkill-modem {
compatible = "rfkill-gpio";
label = "M.2 USB Modem";
radio-type = "wwan";
shutdown-gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
};
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&pmucru CLK_RTC_32K>;
clock-names = "ext_clock";
pinctrl-names = "default";
pinctrl-0 = <&wifi_reg_on_h &clk32k_out1>;
post-power-on-delay-ms = <200>;
reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
};
};
&combphy0 {
status = "okay";
};
&combphy1 {
status = "okay";
};
&combphy2 {
status = "okay";
};
&cpu0 {
cpu-supply = <&vdd_cpu>;
};
&cpu1 {
cpu-supply = <&vdd_cpu>;
};
&cpu2 {
cpu-supply = <&vdd_cpu>;
};
&cpu3 {
cpu-supply = <&vdd_cpu>;
};
/* Motorcomm YT8521SC LAN port (require SGMII) */
&gmac0 {
status = "disabled";
};
/* Motorcomm YT8521SC WAN port */
&gmac1 {
assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
assigned-clock-rates = <0>, <125000000>;
clock_in_out = "output";
phy-handle = <&rgmii_phy>;
phy-mode = "rgmii-id";
phy-supply = <&vcc_3v3>;
pinctrl-names = "default";
pinctrl-0 = <&gmac1m1_miim
&gmac1m1_tx_bus2
&gmac1m1_rx_bus2
&gmac1m1_rgmii_clk
&gmac1m1_rgmii_bus>;
status = "okay";
};
&gpu {
mali-supply = <&vdd_gpu>;
status = "okay";
};
&hdmi {
avdd-0v9-supply = <&vdda_0v9>;
avdd-1v8-supply = <&vcca_1v8>;
status = "okay";
};
&hdmi_in {
hdmi_in_vp0: endpoint {
remote-endpoint = <&vp0_out_hdmi>;
};
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&hdmi_sound {
status = "okay";
};
&i2c0 {
status = "okay";
vdd_cpu: regulator@1c {
compatible = "tcs,tcs4525";
reg = <0x1c>;
fcs,suspend-voltage-selector = <1>;
regulator-name = "vdd_cpu";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1150000>;
regulator-ramp-delay = <2300>;
vin-supply = <&vcc_syson>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2m1_xfer>;
status = "okay";
};
&i2s0_8ch {
status = "okay";
};
&mdio1 {
rgmii_phy: ethernet-phy@3 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0x3>;
reset-assert-us = <20000>;
reset-deassert-us = <100000>;
reset-gpios = <&gpio4 RK_PC0 GPIO_ACTIVE_LOW>;
rx-internal-delay-ps = <1500>;
tx-internal-delay-ps = <1500>;
};
};
&pcie30phy {
status = "okay";
};
/* M.2 E-Key for PCIe WLAN */
&pcie3x2 {
max-link-speed = <1>;
num-lanes = <1>;
pinctrl-names = "default";
pinctrl-0 = <&pcie30x1m0_pins>;
reset-gpios = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>;
vpcie3v3-supply = <&vcc3v3_pcie>;
status = "okay";
};
&pinctrl {
bt {
bt_reg_on_h: bt-reg-on-h {
rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
pcie {
pcie_pwren_h: pcie-pwren-h {
rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
sdmmc0 {
sdmmc0_pwren: sdmmc0-pwren {
rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
usb {
rf_pwr_en: rf-pwr-en {
rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
};
usb_host_pwren_h: usb-host-pwren-h {
rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
wifi {
wifi_reg_on_h: wifi-reg-on-h {
rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
};
&pmu_io_domains {
pmuio1-supply = <&vcc_3v3>;
pmuio2-supply = <&vcc_3v3>;
vccio1-supply = <&vcc_3v3>;
vccio2-supply = <&vcc_1v8>;
vccio3-supply = <&vcc_3v3>;
vccio4-supply = <&vcc_1v8>;
vccio5-supply = <&vcc_3v3>;
vccio6-supply = <&vcc_3v3>;
vccio7-supply = <&vcc_3v3>;
status = "okay";
};
&pwm1 {
status = "okay";
};
&pwm2 {
status = "okay";
};
&saradc {
vref-supply = <&vcca_1v8>;
status = "okay";
};
/* eMMC */
&sdhci {
bus-width = <8>;
max-frequency = <200000000>;
mmc-hs200-1_8v;
non-removable;
pinctrl-names = "default";
pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&vcc_1v8>;
status = "okay";
};
/* Micro SD card slot */
&sdmmc0 {
bus-width = <4>;
cap-sd-highspeed;
cd-gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_LOW>;
disable-wp;
no-1-8-v;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd>;
vmmc-supply = <&vcc3v3_sd>;
vqmmc-supply = <&vcc_3v3>;
status = "okay";
};
/* Qualcomm Atheros QCA9377 WiFi */
&sdmmc1 {
bus-width = <4>;
cap-sd-highspeed;
cap-sdio-irq;
keep-power-in-suspend;
mmc-pwrseq = <&wifi_pwrseq>;
non-removable;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
sd-uhs-sdr104;
vmmc-supply = <&vcc3v3_sys>;
vqmmc-supply = <&vcc_1v8>;
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
wifi: wifi@1 {
reg = <1>;
interrupt-parent = <&gpio2>;
interrupts = <RK_PB2 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "host-wake";
};
};
&tsadc {
rockchip,hw-tshut-mode = <1>;
rockchip,hw-tshut-polarity = <0>;
status = "okay";
};
/* Qualcomm Atheros QCA9377 Bluetooth */
&uart1 {
dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
uart-has-rtscts;
status = "okay";
bluetooth {
compatible = "qcom,qca9377-bt";
clocks = <&pmucru CLK_RTC_32K>;
enable-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&bt_reg_on_h>;
vddio-supply = <&vcc_1v8>;
};
};
/* Debug UART */
&uart2 {
status = "okay";
};
&uart3 {
dma-names = "tx", "rx";
status = "okay";
};
/* Onboard power management MCU */
&uart4 {
dma-names = "tx", "rx";
status = "okay";
};
/* M.2 E-Key for USB Bluetooth */
&usb_host0_ehci {
status = "okay";
};
&usb_host0_ohci {
status = "okay";
};
/* USB Type-A Port */
&usb_host0_xhci {
dr_mode = "host";
status = "okay";
};
/* M.2 B-Key for USB Modem WWAN */
&usb_host1_xhci {
status = "okay";
};
&usb2phy0 {
status = "okay";
};
&usb2phy0_host {
phy-supply = <&vcc3v4_rf>;
status = "okay";
};
&usb2phy0_otg {
phy-supply = <&vcc5v0_usb30_otg0>;
status = "okay";
};
&usb2phy1 {
status = "okay";
};
&usb2phy1_otg {
phy-supply = <&vcc5v0_usb30_otg0>;
status = "okay";
};
&vop {
assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
status = "okay";
};
&vop_mmu {
status = "okay";
};
&vp0 {
vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
reg = <ROCKCHIP_VOP2_EP_HDMI0>;
remote-endpoint = <&hdmi_in_vp0>;
};
};
&xin32k {
pinctrl-names = "default";
pinctrl-0 = <&clk32k_out1>;
};
[ Dauer der Verarbeitung: 0.58 Sekunden
]
