/* SPDX-License-Identifier: GPL-2.0-only */ /* * Registers of Silicon Image SiI8620 Mobile HD Transmitter * * Copyright (C) 2015, Samsung Electronics Co., Ltd. * Andrzej Hajda <a.hajda@samsung.com> * * Based on MHL driver for Android devices. * Copyright (C) 2013-2014 Silicon Image, Inc. #ifndef __SIL_SII8620_H__#define __SIL_SII8620_H__/* Vendor ID Low byte, default value: 0x01 */ #define REG_VND_IDL 0x0000/* Vendor ID High byte, default value: 0x00 */ #define REG_VND_IDH 0x0001/* Device ID Low byte, default value: 0x60 */ #define REG_DEV_IDL 0x0002/* Device ID High byte, default value: 0x86 */ #define REG_DEV_IDH 0x0003/* Device Revision, default value: 0x10 */ #define REG_DEV_REV 0x0004/* OTP DBYTE510, default value: 0x00 */ #define REG_OTP_DBYTE510 0x0006/* System Control #1, default value: 0x00 */ #define REG_SYS_CTRL1 0x0008#define BIT_SYS_CTRL1_OTPVMUTEOVR_SET BIT(7)#define BIT_SYS_CTRL1_VSYNCPIN BIT(6)#define BIT_SYS_CTRL1_OTPADROPOVR_SET BIT(5)#define BIT_SYS_CTRL1_BLOCK_DDC_BY_HPD BIT(4)#define BIT_SYS_CTRL1_OTP2XVOVR_EN BIT(3)#define BIT_SYS_CTRL1_OTP2XAOVR_EN BIT(2)#define BIT_SYS_CTRL1_TX_CTRL_HDMI BIT(1)#define BIT_SYS_CTRL1_OTPAMUTEOVR_SET BIT(0)/* System Control DPD, default value: 0x90 */ #define REG_DPD 0x000b#define BIT_DPD_PWRON_PLL BIT(7)#define BIT_DPD_PDNTX12 BIT(6)#define BIT_DPD_PDNRX12 BIT(5)#define BIT_DPD_OSC_EN BIT(4)#define BIT_DPD_PWRON_HSIC BIT(3)#define BIT_DPD_PDIDCK_N BIT(2)#define BIT_DPD_PD_MHL_CLK_N BIT(1)/* Dual link Control, default value: 0x00 */ #define REG_DCTL 0x000d#define BIT_DCTL_TDM_LCLK_PHASE BIT(7)#define BIT_DCTL_HSIC_CLK_PHASE BIT(6)#define BIT_DCTL_CTS_TCK_PHASE BIT(5)#define BIT_DCTL_EXT_DDC_SEL BIT(4)#define BIT_DCTL_TRANSCODE BIT(3)#define BIT_DCTL_HSIC_RX_STROBE_PHASE BIT(2)#define BIT_DCTL_HSIC_TX_BIST_START_SEL BIT(1)#define BIT_DCTL_TCLKNX_PHASE BIT(0)/* PWD Software Reset, default value: 0x20 */ #define REG_PWD_SRST 0x000e#define BIT_PWD_SRST_COC_DOC_RST BIT(7)#define BIT_PWD_SRST_CBUS_RST_SW BIT(6)#define BIT_PWD_SRST_CBUS_RST_SW_EN BIT(5)#define BIT_PWD_SRST_MHLFIFO_RST BIT(4)#define BIT_PWD_SRST_CBUS_RST BIT(3)#define BIT_PWD_SRST_SW_RST_AUTO BIT(2)#define BIT_PWD_SRST_HDCP2X_SW_RST BIT(1)#define BIT_PWD_SRST_SW_RST BIT(0)/* AKSV_1, default value: 0x00 */ #define REG_AKSV_1 0x001d/* Video H Resolution #1, default value: 0x00 */ #define REG_H_RESL 0x003a/* Video Mode, default value: 0x00 */ #define REG_VID_MODE 0x004a#define BIT_VID_MODE_M1080P BIT(6)/* Video Input Mode, default value: 0xc0 */ #define REG_VID_OVRRD 0x0051#define BIT_VID_OVRRD_PP_AUTO_DISABLE BIT(7)#define BIT_VID_OVRRD_M1080P_OVRRD BIT(6)#define BIT_VID_OVRRD_MINIVSYNC_ON BIT(5)#define BIT_VID_OVRRD_3DCONV_EN_FRAME_PACK BIT(4)#define BIT_VID_OVRRD_ENABLE_AUTO_PATH_EN BIT(3)#define BIT_VID_OVRRD_ENRGB2YCBCR_OVRRD BIT(2)#define BIT_VID_OVRRD_ENDOWNSAMPLE_OVRRD BIT(0)/* I2C Address reassignment, default value: 0x00 */ #define REG_PAGE_MHLSPEC_ADDR 0x0057#define REG_PAGE7_ADDR 0x0058#define REG_PAGE8_ADDR 0x005c/* Fast Interrupt Status, default value: 0x00 */ #define REG_FAST_INTR_STAT 0x005f#define LEN_FAST_INTR_STAT 7#define BIT_FAST_INTR_STAT_TIMR 8#define BIT_FAST_INTR_STAT_INT2 9#define BIT_FAST_INTR_STAT_DDC 10#define BIT_FAST_INTR_STAT_SCDT 11#define BIT_FAST_INTR_STAT_INFR 13#define BIT_FAST_INTR_STAT_EDID 14#define BIT_FAST_INTR_STAT_HDCP 15#define BIT_FAST_INTR_STAT_MSC 16#define BIT_FAST_INTR_STAT_MERR 17#define BIT_FAST_INTR_STAT_G2WB 18#define BIT_FAST_INTR_STAT_G2WB_ERR 19#define BIT_FAST_INTR_STAT_DISC 28#define BIT_FAST_INTR_STAT_BLOCK 30#define BIT_FAST_INTR_STAT_LTRN 31#define BIT_FAST_INTR_STAT_HDCP2 32#define BIT_FAST_INTR_STAT_TDM 42#define BIT_FAST_INTR_STAT_COC 51/* GPIO Control, default value: 0x15 */ #define REG_GPIO_CTRL1 0x006e#define BIT_CTRL1_GPIO_I_8 BIT(5)#define BIT_CTRL1_GPIO_OEN_8 BIT(4)#define BIT_CTRL1_GPIO_I_7 BIT(3)#define BIT_CTRL1_GPIO_OEN_7 BIT(2)#define BIT_CTRL1_GPIO_I_6 BIT(1)#define BIT_CTRL1_GPIO_OEN_6 BIT(0)/* Interrupt Control, default value: 0x06 */ #define REG_INT_CTRL 0x006f#define BIT_INT_CTRL_SOFTWARE_WP BIT(7)#define BIT_INT_CTRL_INTR_OD BIT(2)#define BIT_INT_CTRL_INTR_POLARITY BIT(1)/* Interrupt State, default value: 0x00 */ #define REG_INTR_STATE 0x0070#define BIT_INTR_STATE_INTR_STATE BIT(0)/* Interrupt Source #1, default value: 0x00 */ #define REG_INTR1 0x0071/* Interrupt Source #2, default value: 0x00 */ #define REG_INTR2 0x0072/* Interrupt Source #3, default value: 0x01 */ #define REG_INTR3 0x0073#define BIT_DDC_CMD_DONE BIT(3)/* Interrupt Source #5, default value: 0x00 */ #define REG_INTR5 0x0074/* Interrupt #1 Mask, default value: 0x00 */ #define REG_INTR1_MASK 0x0075/* Interrupt #2 Mask, default value: 0x00 */ #define REG_INTR2_MASK 0x0076/* Interrupt #3 Mask, default value: 0x00 */ #define REG_INTR3_MASK 0x0077/* Interrupt #5 Mask, default value: 0x00 */ #define REG_INTR5_MASK 0x0078#define BIT_INTR_SCDT_CHANGE BIT(0)/* Hot Plug Connection Control, default value: 0x45 */ #define REG_HPD_CTRL 0x0079#define BIT_HPD_CTRL_HPD_DS_SIGNAL BIT(7)#define BIT_HPD_CTRL_HPD_OUT_OD_EN BIT(6)#define BIT_HPD_CTRL_HPD_HIGH BIT(5)#define BIT_HPD_CTRL_HPD_OUT_OVR_EN BIT(4)#define BIT_HPD_CTRL_GPIO_I_1 BIT(3)#define BIT_HPD_CTRL_GPIO_OEN_1 BIT(2)#define BIT_HPD_CTRL_GPIO_I_0 BIT(1)#define BIT_HPD_CTRL_GPIO_OEN_0 BIT(0)/* GPIO Control, default value: 0x55 */ #define REG_GPIO_CTRL 0x007a#define BIT_CTRL_GPIO_I_5 BIT(7)#define BIT_CTRL_GPIO_OEN_5 BIT(6)#define BIT_CTRL_GPIO_I_4 BIT(5)#define BIT_CTRL_GPIO_OEN_4 BIT(4)#define BIT_CTRL_GPIO_I_3 BIT(3)#define BIT_CTRL_GPIO_OEN_3 BIT(2)#define BIT_CTRL_GPIO_I_2 BIT(1)#define BIT_CTRL_GPIO_OEN_2 BIT(0)/* Interrupt Source 7, default value: 0x00 */ #define REG_INTR7 0x007b/* Interrupt Source 8, default value: 0x00 */ #define REG_INTR8 0x007c/* Interrupt #7 Mask, default value: 0x00 */ #define REG_INTR7_MASK 0x007d/* Interrupt #8 Mask, default value: 0x00 */ #define REG_INTR8_MASK 0x007e#define BIT_CEA_NEW_VSI BIT(2)#define BIT_CEA_NEW_AVI BIT(1)/* IEEE, default value: 0x10 */ #define REG_TMDS_CCTRL 0x0080#define BIT_TMDS_CCTRL_TMDS_OE BIT(4)/* TMDS Control #4, default value: 0x02 */ #define REG_TMDS_CTRL4 0x0085#define BIT_TMDS_CTRL4_SCDT_CKDT_SEL BIT(1)#define BIT_TMDS_CTRL4_TX_EN_BY_SCDT BIT(0)/* BIST CNTL, default value: 0x00 */ #define REG_BIST_CTRL 0x00bb#define BIT_RXBIST_VGB_EN BIT(7)#define BIT_TXBIST_VGB_EN BIT(6)#define BIT_BIST_START_SEL BIT(5)#define BIT_BIST_START_BIT BIT(4)#define BIT_BIST_ALWAYS_ON BIT(3)#define BIT_BIST_TRANS BIT(2)#define BIT_BIST_RESET BIT(1)#define BIT_BIST_EN BIT(0)/* BIST DURATION0, default value: 0x00 */ #define REG_BIST_TEST_SEL 0x00bd#define MSK_BIST_TEST_SEL_BIST_PATT_SEL 0x0f/* BIST VIDEO_MODE, default value: 0x00 */ #define REG_BIST_VIDEO_MODE 0x00be#define MSK_BIST_VIDEO_MODE_BIST_VIDEO_MODE_3_0 0x0f/* BIST DURATION0, default value: 0x00 */ #define REG_BIST_DURATION_0 0x00bf/* BIST DURATION1, default value: 0x00 */ #define REG_BIST_DURATION_1 0x00c0/* BIST DURATION2, default value: 0x00 */ #define REG_BIST_DURATION_2 0x00c1/* BIST 8BIT_PATTERN, default value: 0x00 */ #define REG_BIST_8BIT_PATTERN 0x00c2/* LM DDC, default value: 0x80 */ #define REG_LM_DDC 0x00c7#define BIT_LM_DDC_SW_TPI_EN_DISABLED BIT(7)#define BIT_LM_DDC_VIDEO_MUTE_EN BIT(5)#define BIT_LM_DDC_DDC_TPI_SW BIT(2)#define BIT_LM_DDC_DDC_GRANT BIT(1)#define BIT_LM_DDC_DDC_GPU_REQUEST BIT(0)/* DDC I2C Manual, default value: 0x03 */ #define REG_DDC_MANUAL 0x00ec#define BIT_DDC_MANUAL_MAN_DDC BIT(7)#define BIT_DDC_MANUAL_VP_SEL BIT(6)#define BIT_DDC_MANUAL_DSDA BIT(5)#define BIT_DDC_MANUAL_DSCL BIT(4)#define BIT_DDC_MANUAL_GCP_HW_CTL_EN BIT(3)#define BIT_DDC_MANUAL_DDCM_ABORT_WP BIT(2)#define BIT_DDC_MANUAL_IO_DSDA BIT(1)#define BIT_DDC_MANUAL_IO_DSCL BIT(0)/* DDC I2C Target Slave Address, default value: 0x00 */ #define REG_DDC_ADDR 0x00ed#define MSK_DDC_ADDR_DDC_ADDR 0xfe/* DDC I2C Target Segment Address, default value: 0x00 */ #define REG_DDC_SEGM 0x00ee/* DDC I2C Target Offset Address, default value: 0x00 */ #define REG_DDC_OFFSET 0x00ef/* DDC I2C Data In count #1, default value: 0x00 */ #define REG_DDC_DIN_CNT1 0x00f0/* DDC I2C Data In count #2, default value: 0x00 */ #define REG_DDC_DIN_CNT2 0x00f1#define MSK_DDC_DIN_CNT2_DDC_DIN_CNT_9_8 0x03/* DDC I2C Status, default value: 0x04 */ #define REG_DDC_STATUS 0x00f2#define BIT_DDC_STATUS_DDC_BUS_LOW BIT(6)#define BIT_DDC_STATUS_DDC_NO_ACK BIT(5)#define BIT_DDC_STATUS_DDC_I2C_IN_PROG BIT(4)#define BIT_DDC_STATUS_DDC_FIFO_FULL BIT(3)#define BIT_DDC_STATUS_DDC_FIFO_EMPTY BIT(2)#define BIT_DDC_STATUS_DDC_FIFO_READ_IN_SUE BIT(1)#define BIT_DDC_STATUS_DDC_FIFO_WRITE_IN_USE BIT(0)/* DDC I2C Command, default value: 0x70 */ #define REG_DDC_CMD 0x00f3#define BIT_DDC_CMD_HDCP_DDC_EN BIT(6)#define BIT_DDC_CMD_SDA_DEL_EN BIT(5)#define BIT_DDC_CMD_DDC_FLT_EN BIT(4)#define MSK_DDC_CMD_DDC_CMD 0x0f#define VAL_DDC_CMD_ENH_DDC_READ_NO_ACK 0x04#define VAL_DDC_CMD_DDC_CMD_CLEAR_FIFO 0x09#define VAL_DDC_CMD_DDC_CMD_ABORT 0x0f/* DDC I2C FIFO Data In/Out, default value: 0x00 */ #define REG_DDC_DATA 0x00f4/* DDC I2C Data Out Counter, default value: 0x00 */ #define REG_DDC_DOUT_CNT 0x00f5#define BIT_DDC_DOUT_CNT_DDC_DELAY_CNT_8 BIT(7)#define MSK_DDC_DOUT_CNT_DDC_DATA_OUT_CNT 0x1f/* DDC I2C Delay Count, default value: 0x14 */ #define REG_DDC_DELAY_CNT 0x00f6/* Test Control, default value: 0x80 */ #define REG_TEST_TXCTRL 0x00f7#define BIT_TEST_TXCTRL_RCLK_REF_SEL BIT(7)#define BIT_TEST_TXCTRL_PCLK_REF_SEL BIT(6)#define MSK_TEST_TXCTRL_BYPASS_PLL_CLK 0x3c#define BIT_TEST_TXCTRL_HDMI_MODE BIT(1)#define BIT_TEST_TXCTRL_TST_PLLCK BIT(0)/* CBUS Address, default value: 0x00 */ #define REG_PAGE_CBUS_ADDR 0x00f8/* I2C Device Address re-assignment */ #define REG_PAGE1_ADDR 0x00fc#define REG_PAGE2_ADDR 0x00fd#define REG_PAGE3_ADDR 0x00fe#define REG_HW_TPI_ADDR 0x00ff/* USBT CTRL0, default value: 0x00 */ #define REG_UTSRST 0x0100#define BIT_UTSRST_FC_SRST BIT(5)#define BIT_UTSRST_KEEPER_SRST BIT(4)#define BIT_UTSRST_HTX_SRST BIT(3)#define BIT_UTSRST_TRX_SRST BIT(2)#define BIT_UTSRST_TTX_SRST BIT(1)#define BIT_UTSRST_HRX_SRST BIT(0)/* HSIC RX Control3, default value: 0x07 */ #define REG_HRXCTRL3 0x0104#define MSK_HRXCTRL3_HRX_AFFCTRL 0xf0#define BIT_HRXCTRL3_HRX_OUT_EN BIT(2)#define BIT_HRXCTRL3_STATUS_EN BIT(1)#define BIT_HRXCTRL3_HRX_STAY_RESET BIT(0)/* HSIC RX INT Registers */ #define REG_HRXINTL 0x0111#define REG_HRXINTH 0x0112/* TDM TX NUMBITS, default value: 0x0c */ #define REG_TTXNUMB 0x0116#define MSK_TTXNUMB_TTX_AFFCTRL_3_0 0xf0#define BIT_TTXNUMB_TTX_COM1_AT_SYNC_WAIT BIT(3)#define MSK_TTXNUMB_TTX_NUMBPS 0x07/* TDM TX NUMSPISYM, default value: 0x04 */ #define REG_TTXSPINUMS 0x0117/* TDM TX NUMHSICSYM, default value: 0x14 */ #define REG_TTXHSICNUMS 0x0118/* TDM TX NUMTOTSYM, default value: 0x18 */ #define REG_TTXTOTNUMS 0x0119/* TDM TX INT Low, default value: 0x00 */ #define REG_TTXINTL 0x0136#define BIT_TTXINTL_TTX_INTR7 BIT(7)#define BIT_TTXINTL_TTX_INTR6 BIT(6)#define BIT_TTXINTL_TTX_INTR5 BIT(5)#define BIT_TTXINTL_TTX_INTR4 BIT(4)#define BIT_TTXINTL_TTX_INTR3 BIT(3)#define BIT_TTXINTL_TTX_INTR2 BIT(2)#define BIT_TTXINTL_TTX_INTR1 BIT(1)#define BIT_TTXINTL_TTX_INTR0 BIT(0)/* TDM TX INT High, default value: 0x00 */ #define REG_TTXINTH 0x0137#define BIT_TTXINTH_TTX_INTR15 BIT(7)#define BIT_TTXINTH_TTX_INTR14 BIT(6)#define BIT_TTXINTH_TTX_INTR13 BIT(5)#define BIT_TTXINTH_TTX_INTR12 BIT(4)#define BIT_TTXINTH_TTX_INTR11 BIT(3)#define BIT_TTXINTH_TTX_INTR10 BIT(2)#define BIT_TTXINTH_TTX_INTR9 BIT(1)#define BIT_TTXINTH_TTX_INTR8 BIT(0)/* TDM RX Control, default value: 0x1c */ #define REG_TRXCTRL 0x013b#define BIT_TRXCTRL_TRX_CLR_WVALLOW BIT(4)#define BIT_TRXCTRL_TRX_FROM_SE_COC BIT(3)#define MSK_TRXCTRL_TRX_NUMBPS_2_0 0x07/* TDM RX NUMSPISYM, default value: 0x04 */ #define REG_TRXSPINUMS 0x013c/* TDM RX NUMHSICSYM, default value: 0x14 */ #define REG_TRXHSICNUMS 0x013d/* TDM RX NUMTOTSYM, default value: 0x18 */ #define REG_TRXTOTNUMS 0x013e/* TDM RX Status 2nd, default value: 0x00 */ #define REG_TRXSTA2 0x015c#define MSK_TDM_SYNCHRONIZED 0xc0#define VAL_TDM_SYNCHRONIZED 0x80/* TDM RX INT Low, default value: 0x00 */ #define REG_TRXINTL 0x0163/* TDM RX INT High, default value: 0x00 */ #define REG_TRXINTH 0x0164#define BIT_TDM_INTR_SYNC_DATA BIT(0)#define BIT_TDM_INTR_SYNC_WAIT BIT(1)/* TDM RX INTMASK High, default value: 0x00 */ #define REG_TRXINTMH 0x0166/* HSIC TX CRTL, default value: 0x00 */ #define REG_HTXCTRL 0x0169#define BIT_HTXCTRL_HTX_ALLSBE_SOP BIT(4)#define BIT_HTXCTRL_HTX_RGDINV_USB BIT(3)#define BIT_HTXCTRL_HTX_RSPTDM_BUSY BIT(2)#define BIT_HTXCTRL_HTX_DRVCONN1 BIT(1)#define BIT_HTXCTRL_HTX_DRVRST1 BIT(0)/* HSIC TX INT Low, default value: 0x00 */ #define REG_HTXINTL 0x017d/* HSIC TX INT High, default value: 0x00 */ #define REG_HTXINTH 0x017e/* HSIC Keeper, default value: 0x00 */ #define REG_KEEPER 0x0181#define MSK_KEEPER_MODE 0x03#define VAL_KEEPER_MODE_HOST 0#define VAL_KEEPER_MODE_DEVICE 2/* HSIC Flow Control General, default value: 0x02 */ #define REG_FCGC 0x0183#define BIT_FCGC_HSIC_HOSTMODE BIT(1)#define BIT_FCGC_HSIC_ENABLE BIT(0)/* HSIC Flow Control CTR13, default value: 0xfc */ #define REG_FCCTR13 0x0191/* HSIC Flow Control CTR14, default value: 0xff */ #define REG_FCCTR14 0x0192/* HSIC Flow Control CTR15, default value: 0xff */ #define REG_FCCTR15 0x0193/* HSIC Flow Control CTR50, default value: 0x03 */ #define REG_FCCTR50 0x01b6/* HSIC Flow Control INTR0, default value: 0x00 */ #define REG_FCINTR0 0x01ec#define REG_FCINTR1 0x01ed#define REG_FCINTR2 0x01ee#define REG_FCINTR3 0x01ef#define REG_FCINTR4 0x01f0#define REG_FCINTR5 0x01f1#define REG_FCINTR6 0x01f2#define REG_FCINTR7 0x01f3/* TDM Low Latency, default value: 0x20 */ #define REG_TDMLLCTL 0x01fc#define MSK_TDMLLCTL_TRX_LL_SEL_MANUAL 0xc0#define MSK_TDMLLCTL_TRX_LL_SEL_MODE 0x30#define MSK_TDMLLCTL_TTX_LL_SEL_MANUAL 0x0c#define BIT_TDMLLCTL_TTX_LL_TIE_LOW BIT(1)#define BIT_TDMLLCTL_TTX_LL_SEL_MODE BIT(0)/* TMDS 0 Clock Control, default value: 0x10 */ #define REG_TMDS0_CCTRL1 0x0210#define MSK_TMDS0_CCTRL1_TEST_SEL 0xc0#define MSK_TMDS0_CCTRL1_CLK1X_CTL 0x30/* TMDS Clock Enable, default value: 0x00 */ #define REG_TMDS_CLK_EN 0x0211#define BIT_TMDS_CLK_EN_CLK_EN BIT(0)/* TMDS Channel Enable, default value: 0x00 */ #define REG_TMDS_CH_EN 0x0212#define BIT_TMDS_CH_EN_CH0_EN BIT(4)#define BIT_TMDS_CH_EN_CH12_EN BIT(0)/* BGR_BIAS, default value: 0x07 */ #define REG_BGR_BIAS 0x0215#define BIT_BGR_BIAS_BGR_EN BIT(7)#define MSK_BGR_BIAS_BIAS_BGR_D 0x0f/* TMDS 0 Digital I2C BW, default value: 0x0a */ #define REG_ALICE0_BW_I2C 0x0231/* TMDS 0 Digital Zone Control, default value: 0xe0 */ #define REG_ALICE0_ZONE_CTRL 0x024c#define BIT_ALICE0_ZONE_CTRL_ICRST_N BIT(7)#define BIT_ALICE0_ZONE_CTRL_USE_INT_DIV20 BIT(6)#define MSK_ALICE0_ZONE_CTRL_SZONE_I2C 0x30#define MSK_ALICE0_ZONE_CTRL_ZONE_CTRL 0x0f/* TMDS 0 Digital PLL Mode Control, default value: 0x00 */ #define REG_ALICE0_MODE_CTRL 0x024d#define MSK_ALICE0_MODE_CTRL_PLL_MODE_I2C 0x0c#define MSK_ALICE0_MODE_CTRL_DIV20_CTRL 0x03/* MHL Tx Control 6th, default value: 0xa0 */ #define REG_MHLTX_CTL6 0x0285#define MSK_MHLTX_CTL6_EMI_SEL 0xe0#define MSK_MHLTX_CTL6_TX_CLK_SHAPE_9_8 0x03/* Packet Filter0, default value: 0x00 */ #define REG_PKT_FILTER_0 0x0290#define BIT_PKT_FILTER_0_DROP_CEA_GAMUT_PKT BIT(7)#define BIT_PKT_FILTER_0_DROP_CEA_CP_PKT BIT(6)#define BIT_PKT_FILTER_0_DROP_MPEG_PKT BIT(5)#define BIT_PKT_FILTER_0_DROP_SPIF_PKT BIT(4)#define BIT_PKT_FILTER_0_DROP_AIF_PKT BIT(3)#define BIT_PKT_FILTER_0_DROP_AVI_PKT BIT(2)#define BIT_PKT_FILTER_0_DROP_CTS_PKT BIT(1)#define BIT_PKT_FILTER_0_DROP_GCP_PKT BIT(0)/* Packet Filter1, default value: 0x00 */ #define REG_PKT_FILTER_1 0x0291#define BIT_PKT_FILTER_1_VSI_OVERRIDE_DIS BIT(7)#define BIT_PKT_FILTER_1_AVI_OVERRIDE_DIS BIT(6)#define BIT_PKT_FILTER_1_DROP_AUDIO_PKT BIT(3)#define BIT_PKT_FILTER_1_DROP_GEN2_PKT BIT(2)#define BIT_PKT_FILTER_1_DROP_GEN_PKT BIT(1)#define BIT_PKT_FILTER_1_DROP_VSIF_PKT BIT(0)/* TMDS Clock Status, default value: 0x10 */ #define REG_TMDS_CSTAT_P3 0x02a0#define BIT_TMDS_CSTAT_P3_RX_HDMI_CP_CLR_MUTE BIT(7)#define BIT_TMDS_CSTAT_P3_RX_HDMI_CP_SET_MUTE BIT(6)#define BIT_TMDS_CSTAT_P3_RX_HDMI_CP_NEW_CP BIT(5)#define BIT_TMDS_CSTAT_P3_CLR_AVI BIT(3)#define BIT_TMDS_CSTAT_P3_SCDT_CLR_AVI_DIS BIT(2)#define BIT_TMDS_CSTAT_P3_SCDT BIT(1)#define BIT_TMDS_CSTAT_P3_CKDT BIT(0)/* RX_HDMI Control, default value: 0x10 */ #define REG_RX_HDMI_CTRL0 0x02a1#define BIT_RX_HDMI_CTRL0_BYP_DVIFILT_SYNC BIT(5)#define BIT_RX_HDMI_CTRL0_HDMI_MODE_EN_ITSELF_CLR BIT(4)#define BIT_RX_HDMI_CTRL0_HDMI_MODE_SW_VALUE BIT(3)#define BIT_RX_HDMI_CTRL0_HDMI_MODE_OVERWRITE BIT(2)#define BIT_RX_HDMI_CTRL0_RX_HDMI_HDMI_MODE_EN BIT(1)#define BIT_RX_HDMI_CTRL0_RX_HDMI_HDMI_MODE BIT(0)/* RX_HDMI Control, default value: 0x38 */ #define REG_RX_HDMI_CTRL2 0x02a3#define MSK_RX_HDMI_CTRL2_IDLE_CNT 0xf0#define VAL_RX_HDMI_CTRL2_IDLE_CNT(n) ((n) << 4)#define BIT_RX_HDMI_CTRL2_USE_AV_MUTE BIT(3)#define BIT_RX_HDMI_CTRL2_VSI_MON_SEL_VSI BIT(0)/* RX_HDMI Control, default value: 0x0f */ #define REG_RX_HDMI_CTRL3 0x02a4#define MSK_RX_HDMI_CTRL3_PP_MODE_CLK_EN 0x0f/* rx_hdmi Clear Buffer, default value: 0x00 */ #define REG_RX_HDMI_CLR_BUFFER 0x02ac#define MSK_RX_HDMI_CLR_BUFFER_AIF4VSI_CMP 0xc0#define BIT_RX_HDMI_CLR_BUFFER_USE_AIF4VSI BIT(5)#define BIT_RX_HDMI_CLR_BUFFER_VSI_CLR_W_AVI BIT(4)#define BIT_RX_HDMI_CLR_BUFFER_VSI_IEEE_ID_CHK_EN BIT(3)#define BIT_RX_HDMI_CLR_BUFFER_SWAP_VSI_IEEE_ID BIT(2)#define BIT_RX_HDMI_CLR_BUFFER_AIF_CLR_EN BIT(1)#define BIT_RX_HDMI_CLR_BUFFER_VSI_CLR_EN BIT(0)/* RX_HDMI VSI Header1, default value: 0x00 */ #define REG_RX_HDMI_MON_PKT_HEADER1 0x02b8/* RX_HDMI VSI MHL Monitor, default value: 0x3c */ #define REG_RX_HDMI_VSIF_MHL_MON 0x02d7#define MSK_RX_HDMI_VSIF_MHL_MON_RX_HDMI_MHL_3D_FORMAT 0x3c#define MSK_RX_HDMI_VSIF_MHL_MON_RX_HDMI_MHL_VID_FORMAT 0x03/* Interrupt Source 9, default value: 0x00 */ #define REG_INTR9 0x02e0#define BIT_INTR9_EDID_ERROR BIT(6)#define BIT_INTR9_EDID_DONE BIT(5)#define BIT_INTR9_DEVCAP_DONE BIT(4)/* Interrupt 9 Mask, default value: 0x00 */ #define REG_INTR9_MASK 0x02e1/* TPI CBUS Start, default value: 0x00 */ #define REG_TPI_CBUS_START 0x02e2#define BIT_TPI_CBUS_START_RCP_REQ_START BIT(7)#define BIT_TPI_CBUS_START_RCPK_REPLY_START BIT(6)#define BIT_TPI_CBUS_START_RCPE_REPLY_START BIT(5)#define BIT_TPI_CBUS_START_PUT_LINK_MODE_START BIT(4)#define BIT_TPI_CBUS_START_PUT_DCAPCHG_START BIT(3)#define BIT_TPI_CBUS_START_PUT_DCAPRDY_START BIT(2)#define BIT_TPI_CBUS_START_GET_EDID_START_0 BIT(1)#define BIT_TPI_CBUS_START_GET_DEVCAP_START BIT(0)/* EDID Control, default value: 0x10 */ #define REG_EDID_CTRL 0x02e3#define BIT_EDID_CTRL_EDID_PRIME_VALID BIT(7)#define BIT_EDID_CTRL_XDEVCAP_EN BIT(6)#define BIT_EDID_CTRL_DEVCAP_SELECT_DEVCAP BIT(5)#define BIT_EDID_CTRL_EDID_FIFO_ADDR_AUTO BIT(4)#define BIT_EDID_CTRL_EDID_FIFO_ACCESS_ALWAYS_EN BIT(3)#define BIT_EDID_CTRL_EDID_FIFO_BLOCK_SEL BIT(2)#define BIT_EDID_CTRL_INVALID_BKSV BIT(1)#define BIT_EDID_CTRL_EDID_MODE_EN BIT(0)/* EDID FIFO Addr, default value: 0x00 */ #define REG_EDID_FIFO_ADDR 0x02e9/* EDID FIFO Write Data, default value: 0x00 */ #define REG_EDID_FIFO_WR_DATA 0x02ea/* EDID/DEVCAP FIFO Internal Addr, default value: 0x00 */ #define REG_EDID_FIFO_ADDR_MON 0x02eb/* EDID FIFO Read Data, default value: 0x00 */ #define REG_EDID_FIFO_RD_DATA 0x02ec/* EDID DDC Segment Pointer, default value: 0x00 */ #define REG_EDID_START_EXT 0x02ed/* TX IP BIST CNTL and Status, default value: 0x00 */ #define REG_TX_IP_BIST_CNTLSTA 0x02f2#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_QUARTER_CLK_SEL BIT(6)#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_DONE BIT(5)#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_ON BIT(4)#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_RUN BIT(3)#define BIT_TX_IP_BIST_CNTLSTA_TXCLK_HALF_SEL BIT(2)#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_EN BIT(1)#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_SEL BIT(0)/* TX IP BIST INST LOW, default value: 0x00 */ #define REG_TX_IP_BIST_INST_LOW 0x02f3#define REG_TX_IP_BIST_INST_HIGH 0x02f4/* TX IP BIST PATTERN LOW, default value: 0x00 */ #define REG_TX_IP_BIST_PAT_LOW 0x02f5#define REG_TX_IP_BIST_PAT_HIGH 0x02f6/* TX IP BIST CONFIGURE LOW, default value: 0x00 */ #define REG_TX_IP_BIST_CONF_LOW 0x02f7#define REG_TX_IP_BIST_CONF_HIGH 0x02f8/* E-MSC General Control, default value: 0x80 */ #define REG_GENCTL 0x0300#define BIT_GENCTL_SPEC_TRANS_DIS BIT(7)#define BIT_GENCTL_DIS_XMIT_ERR_STATE BIT(6)#define BIT_GENCTL_SPI_MISO_EDGE BIT(5)#define BIT_GENCTL_SPI_MOSI_EDGE BIT(4)#define BIT_GENCTL_CLR_EMSC_RFIFO BIT(3)#define BIT_GENCTL_CLR_EMSC_XFIFO BIT(2)#define BIT_GENCTL_START_TRAIN_SEQ BIT(1)#define BIT_GENCTL_EMSC_EN BIT(0)/* E-MSC Comma ErrorCNT, default value: 0x03 */ #define REG_COMMECNT 0x0305#define BIT_COMMECNT_I2C_TO_EMSC_EN BIT(7)#define MSK_COMMECNT_COMMA_CHAR_ERR_CNT 0x0f/* E-MSC RFIFO ByteCnt, default value: 0x00 */ #define REG_EMSCRFIFOBCNTL 0x031a#define REG_EMSCRFIFOBCNTH 0x031b/* SPI Burst Cnt Status, default value: 0x00 */ #define REG_SPIBURSTCNT 0x031e/* SPI Burst Status and SWRST, default value: 0x00 */ #define REG_SPIBURSTSTAT 0x0322#define BIT_SPIBURSTSTAT_SPI_HDCPRST BIT(7)#define BIT_SPIBURSTSTAT_SPI_CBUSRST BIT(6)#define BIT_SPIBURSTSTAT_SPI_SRST BIT(5)#define BIT_SPIBURSTSTAT_EMSC_NORMAL_MODE BIT(0)/* E-MSC 1st Interrupt, default value: 0x00 */ #define REG_EMSCINTR 0x0323#define BIT_EMSCINTR_EMSC_XFIFO_EMPTY BIT(7)#define BIT_EMSCINTR_EMSC_XMIT_ACK_TOUT BIT(6)#define BIT_EMSCINTR_EMSC_RFIFO_READ_ERR BIT(5)#define BIT_EMSCINTR_EMSC_XFIFO_WRITE_ERR BIT(4)#define BIT_EMSCINTR_EMSC_COMMA_CHAR_ERR BIT(3)#define BIT_EMSCINTR_EMSC_XMIT_DONE BIT(2)#define BIT_EMSCINTR_EMSC_XMIT_GNT_TOUT BIT(1)#define BIT_EMSCINTR_SPI_DVLD BIT(0)/* E-MSC Interrupt Mask, default value: 0x00 */ #define REG_EMSCINTRMASK 0x0324/* I2C E-MSC XMIT FIFO Write Port, default value: 0x00 */ #define REG_EMSC_XMIT_WRITE_PORT 0x032a/* I2C E-MSC RCV FIFO Write Port, default value: 0x00 */ #define REG_EMSC_RCV_READ_PORT 0x032b/* E-MSC 2nd Interrupt, default value: 0x00 */ #define REG_EMSCINTR1 0x032c#define BIT_EMSCINTR1_EMSC_TRAINING_COMMA_ERR BIT(0)/* E-MSC Interrupt Mask, default value: 0x00 */ #define REG_EMSCINTRMASK1 0x032d#define BIT_EMSCINTRMASK1_EMSC_INTRMASK1_0 BIT(0)/* MHL Top Ctl, default value: 0x00 */ #define REG_MHL_TOP_CTL 0x0330#define BIT_MHL_TOP_CTL_MHL3_DOC_SEL BIT(7)#define BIT_MHL_TOP_CTL_MHL_PP_SEL BIT(6)#define MSK_MHL_TOP_CTL_IF_TIMING_CTL 0x03/* MHL DataPath 1st Ctl, default value: 0xbc */ #define REG_MHL_DP_CTL0 0x0331#define BIT_MHL_DP_CTL0_DP_OE BIT(7)#define BIT_MHL_DP_CTL0_TX_OE_OVR BIT(6)#define MSK_MHL_DP_CTL0_TX_OE 0x3f/* MHL DataPath 2nd Ctl, default value: 0xbb */ #define REG_MHL_DP_CTL1 0x0332#define MSK_MHL_DP_CTL1_CK_SWING_CTL 0xf0#define MSK_MHL_DP_CTL1_DT_SWING_CTL 0x0f/* MHL DataPath 3rd Ctl, default value: 0x2f */ #define REG_MHL_DP_CTL2 0x0333#define BIT_MHL_DP_CTL2_CLK_BYPASS_EN BIT(7)#define MSK_MHL_DP_CTL2_DAMP_TERM_SEL 0x30#define MSK_MHL_DP_CTL2_CK_TERM_SEL 0x0c#define MSK_MHL_DP_CTL2_DT_TERM_SEL 0x03/* MHL DataPath 4th Ctl, default value: 0x48 */ #define REG_MHL_DP_CTL3 0x0334#define MSK_MHL_DP_CTL3_DT_DRV_VNBC_CTL 0xf0#define MSK_MHL_DP_CTL3_DT_DRV_VNB_CTL 0x0f/* MHL DataPath 5th Ctl, default value: 0x48 */ #define REG_MHL_DP_CTL4 0x0335#define MSK_MHL_DP_CTL4_CK_DRV_VNBC_CTL 0xf0#define MSK_MHL_DP_CTL4_CK_DRV_VNB_CTL 0x0f/* MHL DataPath 6th Ctl, default value: 0x3f */ #define REG_MHL_DP_CTL5 0x0336#define BIT_MHL_DP_CTL5_RSEN_EN_OVR BIT(7)#define BIT_MHL_DP_CTL5_RSEN_EN BIT(6)#define MSK_MHL_DP_CTL5_DAMP_TERM_VGS_CTL 0x30#define MSK_MHL_DP_CTL5_CK_TERM_VGS_CTL 0x0c#define MSK_MHL_DP_CTL5_DT_TERM_VGS_CTL 0x03/* MHL PLL 1st Ctl, default value: 0x05 */ #define REG_MHL_PLL_CTL0 0x0337#define BIT_MHL_PLL_CTL0_AUD_CLK_EN BIT(7)#define MSK_MHL_PLL_CTL0_AUD_CLK_RATIO 0x70#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_10 0x70#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_6 0x60#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_4 0x50#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_2 0x40#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_5 0x30#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_3 0x20#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_2_PRIME 0x10#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_1 0x00#define MSK_MHL_PLL_CTL0_HDMI_CLK_RATIO 0x0c#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_4X 0x0c#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_2X 0x08#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_1X 0x04#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_HALF_X 0x00#define BIT_MHL_PLL_CTL0_CRYSTAL_CLK_SEL BIT(1)#define BIT_MHL_PLL_CTL0_ZONE_MASK_OE BIT(0)/* MHL PLL 3rd Ctl, default value: 0x80 */ #define REG_MHL_PLL_CTL2 0x0339#define BIT_MHL_PLL_CTL2_CLKDETECT_EN BIT(7)#define BIT_MHL_PLL_CTL2_MEAS_FVCO BIT(3)#define BIT_MHL_PLL_CTL2_PLL_FAST_LOCK BIT(2)#define MSK_MHL_PLL_CTL2_PLL_LF_SEL 0x03/* MHL CBUS 1st Ctl, default value: 0x12 */ #define REG_MHL_CBUS_CTL0 0x0340#define BIT_MHL_CBUS_CTL0_CBUS_RGND_TEST_MODE BIT(7)#define MSK_MHL_CBUS_CTL0_CBUS_RGND_VTH_CTL 0x30#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_734 0x00#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_747 0x10#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_740 0x20#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_754 0x30#define MSK_MHL_CBUS_CTL0_CBUS_RES_TEST_SEL 0x0c#define MSK_MHL_CBUS_CTL0_CBUS_DRV_SEL 0x03#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_WEAKEST 0x00#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_WEAK 0x01#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_STRONG 0x02#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_STRONGEST 0x03/* MHL CBUS 2nd Ctl, default value: 0x03 */ #define REG_MHL_CBUS_CTL1 0x0341#define MSK_MHL_CBUS_CTL1_CBUS_RGND_RES_CTL 0x07#define VAL_MHL_CBUS_CTL1_0888_OHM 0x00#define VAL_MHL_CBUS_CTL1_1115_OHM 0x04#define VAL_MHL_CBUS_CTL1_1378_OHM 0x07/* MHL CoC 1st Ctl, default value: 0xc3 */ #define REG_MHL_COC_CTL0 0x0342#define BIT_MHL_COC_CTL0_COC_BIAS_EN BIT(7)#define MSK_MHL_COC_CTL0_COC_BIAS_CTL 0x70#define MSK_MHL_COC_CTL0_COC_TERM_CTL 0x07/* MHL CoC 2nd Ctl, default value: 0x87 */ #define REG_MHL_COC_CTL1 0x0343#define BIT_MHL_COC_CTL1_COC_EN BIT(7)#define MSK_MHL_COC_CTL1_COC_DRV_CTL 0x3f/* MHL CoC 4th Ctl, default value: 0x00 */ #define REG_MHL_COC_CTL3 0x0345#define BIT_MHL_COC_CTL3_COC_AECHO_EN BIT(0)/* MHL CoC 5th Ctl, default value: 0x28 */ #define REG_MHL_COC_CTL4 0x0346#define MSK_MHL_COC_CTL4_COC_IF_CTL 0xf0#define MSK_MHL_COC_CTL4_COC_SLEW_CTL 0x0f/* MHL CoC 6th Ctl, default value: 0x0d */ #define REG_MHL_COC_CTL5 0x0347/* MHL DoC 1st Ctl, default value: 0x18 */ #define REG_MHL_DOC_CTL0 0x0349#define BIT_MHL_DOC_CTL0_DOC_RXDATA_EN BIT(7)#define MSK_MHL_DOC_CTL0_DOC_DM_TERM 0x38#define MSK_MHL_DOC_CTL0_DOC_OPMODE 0x06#define BIT_MHL_DOC_CTL0_DOC_RXBIAS_EN BIT(0)/* MHL DataPath 7th Ctl, default value: 0x2a */ #define REG_MHL_DP_CTL6 0x0350#define BIT_MHL_DP_CTL6_DP_TAP2_SGN BIT(5)#define BIT_MHL_DP_CTL6_DP_TAP2_EN BIT(4)#define BIT_MHL_DP_CTL6_DP_TAP1_SGN BIT(3)#define BIT_MHL_DP_CTL6_DP_TAP1_EN BIT(2)#define BIT_MHL_DP_CTL6_DT_PREDRV_FEEDCAP_EN BIT(1)#define BIT_MHL_DP_CTL6_DP_PRE_POST_SEL BIT(0)/* MHL DataPath 8th Ctl, default value: 0x06 */ #define REG_MHL_DP_CTL7 0x0351#define MSK_MHL_DP_CTL7_DT_DRV_VBIAS_CASCTL 0xf0#define MSK_MHL_DP_CTL7_DT_DRV_IREF_CTL 0x0f#define REG_MHL_DP_CTL8 0x0352/* Tx Zone Ctl1, default value: 0x00 */ #define REG_TX_ZONE_CTL1 0x0361#define VAL_TX_ZONE_CTL1_TX_ZONE_CTRL_MODE 0x08/* MHL3 Tx Zone Ctl, default value: 0x00 */ #define REG_MHL3_TX_ZONE_CTL 0x0364#define BIT_MHL3_TX_ZONE_CTL_MHL2_INTPLT_ZONE_MANU_EN BIT(7)#define MSK_MHL3_TX_ZONE_CTL_MHL3_TX_ZONE 0x03#define MSK_TX_ZONE_CTL3_TX_ZONE 0x03#define VAL_TX_ZONE_CTL3_TX_ZONE_6GBPS 0x00#define VAL_TX_ZONE_CTL3_TX_ZONE_3GBPS 0x01#define VAL_TX_ZONE_CTL3_TX_ZONE_1_5GBPS 0x02/* HDCP Polling Control and Status, default value: 0x70 */ #define REG_HDCP2X_POLL_CS 0x0391#define BIT_HDCP2X_POLL_CS_HDCP2X_MSG_SZ_CLR_OPTION BIT(6)#define BIT_HDCP2X_POLL_CS_HDCP2X_RPT_READY_CLR_OPTION BIT(5)#define BIT_HDCP2X_POLL_CS_HDCP2X_REAUTH_REQ_CLR_OPTION BIT(4)#define MSK_HDCP2X_POLL_CS_ 0x0c#define BIT_HDCP2X_POLL_CS_HDCP2X_DIS_POLL_GNT BIT(1)#define BIT_HDCP2X_POLL_CS_HDCP2X_DIS_POLL_EN BIT(0)/* HDCP Interrupt 0, default value: 0x00 */ #define REG_HDCP2X_INTR0 0x0398/* HDCP Interrupt 0 Mask, default value: 0x00 */ #define REG_HDCP2X_INTR0_MASK 0x0399/* HDCP General Control 0, default value: 0x02 */ #define REG_HDCP2X_CTRL_0 0x03a0#define BIT_HDCP2X_CTRL_0_HDCP2X_ENCRYPT_EN BIT(7)#define BIT_HDCP2X_CTRL_0_HDCP2X_POLINT_SEL BIT(6)#define BIT_HDCP2X_CTRL_0_HDCP2X_POLINT_OVR BIT(5)#define BIT_HDCP2X_CTRL_0_HDCP2X_PRECOMPUTE BIT(4)#define BIT_HDCP2X_CTRL_0_HDCP2X_HDMIMODE BIT(3)#define BIT_HDCP2X_CTRL_0_HDCP2X_REPEATER BIT(2)#define BIT_HDCP2X_CTRL_0_HDCP2X_HDCPTX BIT(1)#define BIT_HDCP2X_CTRL_0_HDCP2X_EN BIT(0)/* HDCP General Control 1, default value: 0x08 */ #define REG_HDCP2X_CTRL_1 0x03a1#define MSK_HDCP2X_CTRL_1_HDCP2X_REAUTH_MSK_3_0 0xf0#define BIT_HDCP2X_CTRL_1_HDCP2X_HPD_SW BIT(3)#define BIT_HDCP2X_CTRL_1_HDCP2X_HPD_OVR BIT(2)#define BIT_HDCP2X_CTRL_1_HDCP2X_CTL3MSK BIT(1)#define BIT_HDCP2X_CTRL_1_HDCP2X_REAUTH_SW BIT(0)/* HDCP Misc Control, default value: 0x00 */ #define REG_HDCP2X_MISC_CTRL 0x03a5#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_SMNG_XFER_START BIT(4)#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_SMNG_WR_START BIT(3)#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_SMNG_WR BIT(2)#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_RCVID_RD_START BIT(1)#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_RCVID_RD BIT(0)/* HDCP RPT SMNG K, default value: 0x00 */ #define REG_HDCP2X_RPT_SMNG_K 0x03a6/* HDCP RPT SMNG In, default value: 0x00 */ #define REG_HDCP2X_RPT_SMNG_IN 0x03a7/* HDCP Auth Status, default value: 0x00 */ #define REG_HDCP2X_AUTH_STAT 0x03aa/* HDCP RPT RCVID Out, default value: 0x00 */ #define REG_HDCP2X_RPT_RCVID_OUT 0x03ac/* HDCP TP1, default value: 0x62 */ #define REG_HDCP2X_TP1 0x03b4/* HDCP GP Out 0, default value: 0x00 */ #define REG_HDCP2X_GP_OUT0 0x03c7/* HDCP Repeater RCVR ID 0, default value: 0x00 */ #define REG_HDCP2X_RPT_RCVR_ID0 0x03d1/* HDCP DDCM Status, default value: 0x00 */ #define REG_HDCP2X_DDCM_STS 0x03d8#define MSK_HDCP2X_DDCM_STS_HDCP2X_DDCM_ERR_STS_3_0 0xf0#define MSK_HDCP2X_DDCM_STS_HDCP2X_DDCM_CTL_CS_3_0 0x0f/* HDMI2MHL3 Control, default value: 0x0a */ #define REG_M3_CTRL 0x03e0#define BIT_M3_CTRL_H2M_SWRST BIT(4)#define BIT_M3_CTRL_SW_MHL3_SEL BIT(3)#define BIT_M3_CTRL_M3AV_EN BIT(2)#define BIT_M3_CTRL_ENC_TMDS BIT(1)#define BIT_M3_CTRL_MHL3_MASTER_EN BIT(0)#define VAL_M3_CTRL_MHL1_2_VALUE (BIT_M3_CTRL_SW_MHL3_SEL \#define VAL_M3_CTRL_MHL3_VALUE (BIT_M3_CTRL_SW_MHL3_SEL \/* HDMI2MHL3 Port0 Control, default value: 0x04 */ #define REG_M3_P0CTRL 0x03e1#define BIT_M3_P0CTRL_MHL3_P0_HDCP_ENC_EN BIT(4)#define BIT_M3_P0CTRL_MHL3_P0_UNLIMIT_EN BIT(3)#define BIT_M3_P0CTRL_MHL3_P0_HDCP_EN BIT(2)#define BIT_M3_P0CTRL_MHL3_P0_PIXEL_MODE_PACKED BIT(1)#define BIT_M3_P0CTRL_MHL3_P0_PORT_EN BIT(0)#define REG_M3_POSTM 0x03e2#define MSK_M3_POSTM_RRP_DECODE 0xf8#define MSK_M3_POSTM_MHL3_P0_STM_ID 0x07/* HDMI2MHL3 Scramble Control, default value: 0x41 */ #define REG_M3_SCTRL 0x03e6#define MSK_M3_SCTRL_MHL3_SR_LENGTH 0xf0#define BIT_M3_SCTRL_MHL3_SCRAMBLER_EN BIT(0)/* HSIC Div Ctl, default value: 0x05 */ #define REG_DIV_CTL_MAIN 0x03f2#define MSK_DIV_CTL_MAIN_PRE_DIV_CTL_MAIN 0x1c#define MSK_DIV_CTL_MAIN_FB_DIV_CTL_MAIN 0x03/* MHL Capability 1st Byte, default value: 0x00 */ #define REG_MHL_DEVCAP_0 0x0400/* MHL Interrupt 1st Byte, default value: 0x00 */ #define REG_MHL_INT_0 0x0420/* Device Status 1st byte, default value: 0x00 */ #define REG_MHL_STAT_0 0x0430/* CBUS Scratch Pad 1st Byte, default value: 0x00 */ #define REG_MHL_SCRPAD_0 0x0440/* MHL Extended Capability 1st Byte, default value: 0x00 */ #define REG_MHL_EXTDEVCAP_0 0x0480/* Device Extended Status 1st byte, default value: 0x00 */ #define REG_MHL_EXTSTAT_0 0x0490/* TPI DTD Byte2, default value: 0x00 */ #define REG_TPI_DTD_B2 0x0602#define VAL_TPI_QUAN_RANGE_LIMITED 0x01#define VAL_TPI_QUAN_RANGE_FULL 0x02#define VAL_TPI_FORMAT_RGB 0x00#define VAL_TPI_FORMAT_YCBCR444 0x01#define VAL_TPI_FORMAT_YCBCR422 0x02#define VAL_TPI_FORMAT_INTERNAL_RGB 0x03#define VAL_TPI_FORMAT(_fmt, _qr) \## _fmt | (VAL_TPI_QUAN_RANGE_## _qr << 2))/* Input Format, default value: 0x00 */ #define REG_TPI_INPUT 0x0609#define BIT_TPI_INPUT_EXTENDEDBITMODE BIT(7)#define BIT_TPI_INPUT_ENDITHER BIT(6)#define MSK_TPI_INPUT_INPUT_QUAN_RANGE 0x0c#define MSK_TPI_INPUT_INPUT_FORMAT 0x03/* Output Format, default value: 0x00 */ #define REG_TPI_OUTPUT 0x060a#define BIT_TPI_OUTPUT_CSCMODE709 BIT(4)#define MSK_TPI_OUTPUT_OUTPUT_QUAN_RANGE 0x0c#define MSK_TPI_OUTPUT_OUTPUT_FORMAT 0x03/* TPI AVI Check Sum, default value: 0x00 */ #define REG_TPI_AVI_CHSUM 0x060c/* TPI System Control, default value: 0x00 */ #define REG_TPI_SC 0x061a#define BIT_TPI_SC_TPI_UPDATE_FLG BIT(7)#define BIT_TPI_SC_TPI_REAUTH_CTL BIT(6)#define BIT_TPI_SC_TPI_OUTPUT_MODE_1 BIT(5)#define BIT_TPI_SC_REG_TMDS_OE_POWER_DOWN BIT(4)#define BIT_TPI_SC_TPI_AV_MUTE BIT(3)#define BIT_TPI_SC_DDC_GPU_REQUEST BIT(2)#define BIT_TPI_SC_DDC_TPI_SW BIT(1)#define BIT_TPI_SC_TPI_OUTPUT_MODE_0_HDMI BIT(0)/* TPI COPP Query Data, default value: 0x00 */ #define REG_TPI_COPP_DATA1 0x0629#define BIT_TPI_COPP_DATA1_COPP_GPROT BIT(7)#define BIT_TPI_COPP_DATA1_COPP_LPROT BIT(6)#define MSK_TPI_COPP_DATA1_COPP_LINK_STATUS 0x30#define VAL_TPI_COPP_LINK_STATUS_NORMAL 0x00#define VAL_TPI_COPP_LINK_STATUS_LINK_LOST 0x10#define VAL_TPI_COPP_LINK_STATUS_RENEGOTIATION_REQ 0x20#define VAL_TPI_COPP_LINK_STATUS_LINK_SUSPENDED 0x30#define BIT_TPI_COPP_DATA1_COPP_HDCP_REP BIT(3)#define BIT_TPI_COPP_DATA1_COPP_CONNTYPE_0 BIT(2)#define BIT_TPI_COPP_DATA1_COPP_PROTYPE BIT(1)#define BIT_TPI_COPP_DATA1_COPP_CONNTYPE_1 BIT(0)/* TPI COPP Control Data, default value: 0x00 */ #define REG_TPI_COPP_DATA2 0x062a#define BIT_TPI_COPP_DATA2_INTR_ENCRYPTION BIT(5)#define BIT_TPI_COPP_DATA2_KSV_FORWARD BIT(4)#define BIT_TPI_COPP_DATA2_INTERM_RI_CHECK_EN BIT(3)#define BIT_TPI_COPP_DATA2_DOUBLE_RI_CHECK BIT(2)#define BIT_TPI_COPP_DATA2_DDC_SHORT_RI_RD BIT(1)#define BIT_TPI_COPP_DATA2_COPP_PROTLEVEL BIT(0)/* TPI Interrupt Enable, default value: 0x00 */ #define REG_TPI_INTR_EN 0x063c/* TPI Interrupt Status Low Byte, default value: 0x00 */ #define REG_TPI_INTR_ST0 0x063d#define BIT_TPI_INTR_ST0_TPI_AUTH_CHNGE_STAT BIT(7)#define BIT_TPI_INTR_ST0_TPI_V_RDY_STAT BIT(6)#define BIT_TPI_INTR_ST0_TPI_COPP_CHNGE_STAT BIT(5)#define BIT_TPI_INTR_ST0_KSV_FIFO_FIRST_STAT BIT(3)#define BIT_TPI_INTR_ST0_READ_BKSV_BCAPS_DONE_STAT BIT(2)#define BIT_TPI_INTR_ST0_READ_BKSV_BCAPS_ERR_STAT BIT(1)#define BIT_TPI_INTR_ST0_READ_BKSV_ERR_STAT BIT(0)/* TPI DS BCAPS Status, default value: 0x00 */ #define REG_TPI_DS_BCAPS 0x0644/* TPI BStatus1, default value: 0x00 */ #define REG_TPI_BSTATUS1 0x0645#define BIT_TPI_BSTATUS1_DS_DEV_EXCEED BIT(7)#define MSK_TPI_BSTATUS1_DS_DEV_CNT 0x7f/* TPI BStatus2, default value: 0x10 */ #define REG_TPI_BSTATUS2 0x0646#define MSK_TPI_BSTATUS2_DS_BSTATUS 0xe0#define BIT_TPI_BSTATUS2_DS_HDMI_MODE BIT(4)#define BIT_TPI_BSTATUS2_DS_CASC_EXCEED BIT(3)#define MSK_TPI_BSTATUS2_DS_DEPTH 0x07/* TPI HW Optimization Control #3, default value: 0x00 */ #define REG_TPI_HW_OPT3 0x06bb#define BIT_TPI_HW_OPT3_DDC_DEBUG BIT(7)#define BIT_TPI_HW_OPT3_RI_CHECK_SKIP BIT(3)#define BIT_TPI_HW_OPT3_TPI_DDC_BURST_MODE BIT(2)#define MSK_TPI_HW_OPT3_TPI_DDC_REQ_LEVEL 0x03/* TPI Info Frame Select, default value: 0x00 */ #define REG_TPI_INFO_FSEL 0x06bf#define BIT_TPI_INFO_FSEL_EN BIT(7)#define BIT_TPI_INFO_FSEL_RPT BIT(6)#define BIT_TPI_INFO_FSEL_READ_FLAG BIT(5)#define MSK_TPI_INFO_FSEL_PKT 0x07#define VAL_TPI_INFO_FSEL_AVI 0x00#define VAL_TPI_INFO_FSEL_SPD 0x01#define VAL_TPI_INFO_FSEL_AUD 0x02#define VAL_TPI_INFO_FSEL_MPG 0x03#define VAL_TPI_INFO_FSEL_GEN 0x04#define VAL_TPI_INFO_FSEL_GEN2 0x05#define VAL_TPI_INFO_FSEL_VSI 0x06/* TPI Info Byte #0, default value: 0x00 */ #define REG_TPI_INFO_B0 0x06c0/* CoC Status, default value: 0x00 */ #define REG_COC_STAT_0 0x0700#define BIT_COC_STAT_0_PLL_LOCKED BIT(7)#define MSK_COC_STAT_0_FSM_STATE 0x0f#define REG_COC_STAT_1 0x0701#define REG_COC_STAT_2 0x0702#define REG_COC_STAT_3 0x0703#define REG_COC_STAT_4 0x0704#define REG_COC_STAT_5 0x0705/* CoC 1st Ctl, default value: 0x40 */ #define REG_COC_CTL0 0x0710/* CoC 2nd Ctl, default value: 0x0a */ #define REG_COC_CTL1 0x0711#define MSK_COC_CTL1_COC_CTRL1_7_6 0xc0#define MSK_COC_CTL1_COC_CTRL1_5_0 0x3f/* CoC 3rd Ctl, default value: 0x14 */ #define REG_COC_CTL2 0x0712#define MSK_COC_CTL2_COC_CTRL2_7_6 0xc0#define MSK_COC_CTL2_COC_CTRL2_5_0 0x3f/* CoC 4th Ctl, default value: 0x40 */ #define REG_COC_CTL3 0x0713#define BIT_COC_CTL3_COC_CTRL3_7 BIT(7)#define MSK_COC_CTL3_COC_CTRL3_6_0 0x7f/* CoC 7th Ctl, default value: 0x00 */ #define REG_COC_CTL6 0x0716#define BIT_COC_CTL6_COC_CTRL6_7 BIT(7)#define BIT_COC_CTL6_COC_CTRL6_6 BIT(6)#define MSK_COC_CTL6_COC_CTRL6_5_0 0x3f/* CoC 8th Ctl, default value: 0x06 */ #define REG_COC_CTL7 0x0717#define BIT_COC_CTL7_COC_CTRL7_7 BIT(7)#define BIT_COC_CTL7_COC_CTRL7_6 BIT(6)#define BIT_COC_CTL7_COC_CTRL7_5 BIT(5)#define MSK_COC_CTL7_COC_CTRL7_4_3 0x18#define MSK_COC_CTL7_COC_CTRL7_2_0 0x07/* CoC 10th Ctl, default value: 0x00 */ #define REG_COC_CTL9 0x0719/* CoC 11th Ctl, default value: 0x00 */ #define REG_COC_CTLA 0x071a/* CoC 12th Ctl, default value: 0x00 */ #define REG_COC_CTLB 0x071b/* CoC 13th Ctl, default value: 0x0f */ #define REG_COC_CTLC 0x071c/* CoC 14th Ctl, default value: 0x0a */ #define REG_COC_CTLD 0x071d#define BIT_COC_CTLD_COC_CTRLD_7 BIT(7)#define MSK_COC_CTLD_COC_CTRLD_6_0 0x7f/* CoC 15th Ctl, default value: 0x0a */ #define REG_COC_CTLE 0x071e#define BIT_COC_CTLE_COC_CTRLE_7 BIT(7)#define MSK_COC_CTLE_COC_CTRLE_6_0 0x7f/* CoC 16th Ctl, default value: 0x00 */ #define REG_COC_CTLF 0x071f#define MSK_COC_CTLF_COC_CTRLF_7_3 0xf8#define MSK_COC_CTLF_COC_CTRLF_2_0 0x07/* CoC 18th Ctl, default value: 0x32 */ #define REG_COC_CTL11 0x0721#define MSK_COC_CTL11_COC_CTRL11_7_4 0xf0#define MSK_COC_CTL11_COC_CTRL11_3_0 0x0f/* CoC 21st Ctl, default value: 0x00 */ #define REG_COC_CTL14 0x0724#define MSK_COC_CTL14_COC_CTRL14_7_4 0xf0#define MSK_COC_CTL14_COC_CTRL14_3_0 0x0f/* CoC 22nd Ctl, default value: 0x00 */ #define REG_COC_CTL15 0x0725#define BIT_COC_CTL15_COC_CTRL15_7 BIT(7)#define MSK_COC_CTL15_COC_CTRL15_6_4 0x70#define MSK_COC_CTL15_COC_CTRL15_3_0 0x0f/* CoC Interrupt, default value: 0x00 */ #define REG_COC_INTR 0x0726/* CoC Interrupt Mask, default value: 0x00 */ #define REG_COC_INTR_MASK 0x0727#define BIT_COC_PLL_LOCK_STATUS_CHANGE BIT(0)#define BIT_COC_CALIBRATION_DONE BIT(1)/* CoC Misc Ctl, default value: 0x00 */ #define REG_COC_MISC_CTL0 0x0728#define BIT_COC_MISC_CTL0_FSM_MON BIT(7)/* CoC 24th Ctl, default value: 0x00 */ #define REG_COC_CTL17 0x072a#define MSK_COC_CTL17_COC_CTRL17_7_4 0xf0#define MSK_COC_CTL17_COC_CTRL17_3_0 0x0f/* CoC 25th Ctl, default value: 0x00 */ #define REG_COC_CTL18 0x072b#define MSK_COC_CTL18_COC_CTRL18_7_4 0xf0#define MSK_COC_CTL18_COC_CTRL18_3_0 0x0f/* CoC 26th Ctl, default value: 0x00 */ #define REG_COC_CTL19 0x072c#define MSK_COC_CTL19_COC_CTRL19_7_4 0xf0#define MSK_COC_CTL19_COC_CTRL19_3_0 0x0f/* CoC 27th Ctl, default value: 0x00 */ #define REG_COC_CTL1A 0x072d#define MSK_COC_CTL1A_COC_CTRL1A_7_2 0xfc#define MSK_COC_CTL1A_COC_CTRL1A_1_0 0x03/* DoC 9th Status, default value: 0x00 */ #define REG_DOC_STAT_8 0x0740/* DoC 10th Status, default value: 0x00 */ #define REG_DOC_STAT_9 0x0741/* DoC 5th CFG, default value: 0x00 */ #define REG_DOC_CFG4 0x074e#define MSK_DOC_CFG4_DBG_STATE_DOC_FSM 0x0f/* DoC 1st Ctl, default value: 0x40 */ #define REG_DOC_CTL0 0x0751/* DoC 7th Ctl, default value: 0x00 */ #define REG_DOC_CTL6 0x0757#define BIT_DOC_CTL6_DOC_CTRL6_7 BIT(7)#define BIT_DOC_CTL6_DOC_CTRL6_6 BIT(6)#define MSK_DOC_CTL6_DOC_CTRL6_5_4 0x30#define MSK_DOC_CTL6_DOC_CTRL6_3_0 0x0f/* DoC 8th Ctl, default value: 0x00 */ #define REG_DOC_CTL7 0x0758#define BIT_DOC_CTL7_DOC_CTRL7_7 BIT(7)#define BIT_DOC_CTL7_DOC_CTRL7_6 BIT(6)#define BIT_DOC_CTL7_DOC_CTRL7_5 BIT(5)#define MSK_DOC_CTL7_DOC_CTRL7_4_3 0x18#define MSK_DOC_CTL7_DOC_CTRL7_2_0 0x07/* DoC 9th Ctl, default value: 0x00 */ #define REG_DOC_CTL8 0x076c#define BIT_DOC_CTL8_DOC_CTRL8_7 BIT(7)#define MSK_DOC_CTL8_DOC_CTRL8_6_4 0x70#define MSK_DOC_CTL8_DOC_CTRL8_3_2 0x0c#define MSK_DOC_CTL8_DOC_CTRL8_1_0 0x03/* DoC 10th Ctl, default value: 0x00 */ #define REG_DOC_CTL9 0x076d/* DoC 11th Ctl, default value: 0x00 */ #define REG_DOC_CTLA 0x076e/* DoC 15th Ctl, default value: 0x00 */ #define REG_DOC_CTLE 0x0772#define BIT_DOC_CTLE_DOC_CTRLE_7 BIT(7)#define BIT_DOC_CTLE_DOC_CTRLE_6 BIT(6)#define MSK_DOC_CTLE_DOC_CTRLE_5_4 0x30#define MSK_DOC_CTLE_DOC_CTRLE_3_0 0x0f/* Interrupt Mask 1st, default value: 0x00 */ #define REG_MHL_INT_0_MASK 0x0580/* Interrupt Mask 2nd, default value: 0x00 */ #define REG_MHL_INT_1_MASK 0x0581/* Interrupt Mask 3rd, default value: 0x00 */ #define REG_MHL_INT_2_MASK 0x0582/* Interrupt Mask 4th, default value: 0x00 */ #define REG_MHL_INT_3_MASK 0x0583/* MDT Receive Time Out, default value: 0x00 */ #define REG_MDT_RCV_TIMEOUT 0x0584/* MDT Transmit Time Out, default value: 0x00 */ #define REG_MDT_XMIT_TIMEOUT 0x0585/* MDT Receive Control, default value: 0x00 */ #define REG_MDT_RCV_CTRL 0x0586#define BIT_MDT_RCV_CTRL_MDT_RCV_EN BIT(7)#define BIT_MDT_RCV_CTRL_MDT_DELAY_RCV_EN BIT(6)#define BIT_MDT_RCV_CTRL_MDT_RFIFO_OVER_WR_EN BIT(4)#define BIT_MDT_RCV_CTRL_MDT_XFIFO_OVER_WR_EN BIT(3)#define BIT_MDT_RCV_CTRL_MDT_DISABLE BIT(2)#define BIT_MDT_RCV_CTRL_MDT_RFIFO_CLR_ALL BIT(1)#define BIT_MDT_RCV_CTRL_MDT_RFIFO_CLR_CUR BIT(0)/* MDT Receive Read Port, default value: 0x00 */ #define REG_MDT_RCV_READ_PORT 0x0587/* MDT Transmit Control, default value: 0x70 */ #define REG_MDT_XMIT_CTRL 0x0588#define BIT_MDT_XMIT_CTRL_EN BIT(7)#define BIT_MDT_XMIT_CTRL_CMD_MERGE_EN BIT(6)#define BIT_MDT_XMIT_CTRL_FIXED_BURST_LEN BIT(5)#define BIT_MDT_XMIT_CTRL_FIXED_AID BIT(4)#define BIT_MDT_XMIT_CTRL_SINGLE_RUN_EN BIT(3)#define BIT_MDT_XMIT_CTRL_CLR_ABORT_WAIT BIT(2)#define BIT_MDT_XMIT_CTRL_XFIFO_CLR_ALL BIT(1)#define BIT_MDT_XMIT_CTRL_XFIFO_CLR_CUR BIT(0)/* MDT Receive WRITE Port, default value: 0x00 */ #define REG_MDT_XMIT_WRITE_PORT 0x0589/* MDT RFIFO Status, default value: 0x00 */ #define REG_MDT_RFIFO_STAT 0x058a#define MSK_MDT_RFIFO_STAT_MDT_RFIFO_CNT 0xe0#define MSK_MDT_RFIFO_STAT_MDT_RFIFO_CUR_BYTE_CNT 0x1f/* MDT XFIFO Status, default value: 0x80 */ #define REG_MDT_XFIFO_STAT 0x058b#define MSK_MDT_XFIFO_STAT_MDT_XFIFO_LEVEL_AVAIL 0xe0#define BIT_MDT_XFIFO_STAT_MDT_XMIT_PRE_HS_EN BIT(4)#define MSK_MDT_XFIFO_STAT_MDT_WRITE_BURST_LEN 0x0f/* MDT Interrupt 0, default value: 0x0c */ #define REG_MDT_INT_0 0x058c#define BIT_MDT_RFIFO_DATA_RDY BIT(0)#define BIT_MDT_IDLE_AFTER_HAWB_DISABLE BIT(2)#define BIT_MDT_XFIFO_EMPTY BIT(3)/* MDT Interrupt 0 Mask, default value: 0x00 */ #define REG_MDT_INT_0_MASK 0x058d/* MDT Interrupt 1, default value: 0x00 */ #define REG_MDT_INT_1 0x058e#define BIT_MDT_RCV_TIMEOUT BIT(0)#define BIT_MDT_RCV_SM_ABORT_PKT_RCVD BIT(1)#define BIT_MDT_RCV_SM_ERROR BIT(2)#define BIT_MDT_XMIT_TIMEOUT BIT(5)#define BIT_MDT_XMIT_SM_ABORT_PKT_RCVD BIT(6)#define BIT_MDT_XMIT_SM_ERROR BIT(7)/* MDT Interrupt 1 Mask, default value: 0x00 */ #define REG_MDT_INT_1_MASK 0x058f/* CBUS Vendor ID, default value: 0x01 */ #define REG_CBUS_VENDOR_ID 0x0590/* CBUS Connection Status, default value: 0x00 */ #define REG_CBUS_STATUS 0x0591#define BIT_CBUS_STATUS_MHL_CABLE_PRESENT BIT(4)#define BIT_CBUS_STATUS_MSC_HB_SUCCESS BIT(3)#define BIT_CBUS_STATUS_CBUS_HPD BIT(2)#define BIT_CBUS_STATUS_MHL_MODE BIT(1)#define BIT_CBUS_STATUS_CBUS_CONNECTED BIT(0)/* CBUS Interrupt 1st, default value: 0x00 */ #define REG_CBUS_INT_0 0x0592#define BIT_CBUS_MSC_MT_DONE_NACK BIT(7)#define BIT_CBUS_MSC_MR_SET_INT BIT(6)#define BIT_CBUS_MSC_MR_WRITE_BURST BIT(5)#define BIT_CBUS_MSC_MR_MSC_MSG BIT(4)#define BIT_CBUS_MSC_MR_WRITE_STAT BIT(3)#define BIT_CBUS_HPD_CHG BIT(2)#define BIT_CBUS_MSC_MT_DONE BIT(1)#define BIT_CBUS_CNX_CHG BIT(0)/* CBUS Interrupt Mask 1st, default value: 0x00 */ #define REG_CBUS_INT_0_MASK 0x0593/* CBUS Interrupt 2nd, default value: 0x00 */ #define REG_CBUS_INT_1 0x0594#define BIT_CBUS_CMD_ABORT BIT(6)#define BIT_CBUS_MSC_ABORT_RCVD BIT(3)#define BIT_CBUS_DDC_ABORT BIT(2)#define BIT_CBUS_CEC_ABORT BIT(1)/* CBUS Interrupt Mask 2nd, default value: 0x00 */ #define REG_CBUS_INT_1_MASK 0x0595/* CBUS DDC Abort Interrupt, default value: 0x00 */ #define REG_DDC_ABORT_INT 0x0598/* CBUS DDC Abort Interrupt Mask, default value: 0x00 */ #define REG_DDC_ABORT_INT_MASK 0x0599/* CBUS MSC Requester Abort Interrupt, default value: 0x00 */ #define REG_MSC_MT_ABORT_INT 0x059a/* CBUS MSC Requester Abort Interrupt Mask, default value: 0x00 */ #define REG_MSC_MT_ABORT_INT_MASK 0x059b/* CBUS MSC Responder Abort Interrupt, default value: 0x00 */ #define REG_MSC_MR_ABORT_INT 0x059c/* CBUS MSC Responder Abort Interrupt Mask, default value: 0x00 */ #define REG_MSC_MR_ABORT_INT_MASK 0x059d/* CBUS RX DISCOVERY interrupt, default value: 0x00 */ #define REG_CBUS_RX_DISC_INT0 0x059e/* CBUS RX DISCOVERY Interrupt Mask, default value: 0x00 */ #define REG_CBUS_RX_DISC_INT0_MASK 0x059f/* CBUS_Link_Layer Control #8, default value: 0x00 */ #define REG_CBUS_LINK_CTRL_8 0x05a7/* MDT State Machine Status, default value: 0x00 */ #define REG_MDT_SM_STAT 0x05b5#define MSK_MDT_SM_STAT_MDT_RCV_STATE 0xf0#define MSK_MDT_SM_STAT_MDT_XMIT_STATE 0x0f/* CBUS MSC command trigger, default value: 0x00 */ #define REG_MSC_COMMAND_START 0x05b8#define BIT_MSC_COMMAND_START_DEBUG BIT(5)#define BIT_MSC_COMMAND_START_WRITE_BURST BIT(4)#define BIT_MSC_COMMAND_START_WRITE_STAT BIT(3)#define BIT_MSC_COMMAND_START_READ_DEVCAP BIT(2)#define BIT_MSC_COMMAND_START_MSC_MSG BIT(1)#define BIT_MSC_COMMAND_START_PEER BIT(0)/* CBUS MSC Command/Offset, default value: 0x00 */ #define REG_MSC_CMD_OR_OFFSET 0x05b9/* CBUS MSC Transmit Data */ #define REG_MSC_1ST_TRANSMIT_DATA 0x05ba#define REG_MSC_2ND_TRANSMIT_DATA 0x05bb/* CBUS MSC Requester Received Data */ #define REG_MSC_MT_RCVD_DATA0 0x05bc#define REG_MSC_MT_RCVD_DATA1 0x05bd/* CBUS MSC Responder MSC_MSG Received Data */ #define REG_MSC_MR_MSC_MSG_RCVD_1ST_DATA 0x05bf#define REG_MSC_MR_MSC_MSG_RCVD_2ND_DATA 0x05c0/* CBUS MSC Heartbeat Control, default value: 0x27 */ #define REG_MSC_HEARTBEAT_CTRL 0x05c4#define BIT_MSC_HEARTBEAT_CTRL_MSC_HB_EN BIT(7)#define MSK_MSC_HEARTBEAT_CTRL_MSC_HB_FAIL_LIMIT 0x70#define MSK_MSC_HEARTBEAT_CTRL_MSC_HB_PERIOD_MSB 0x0f/* CBUS MSC Compatibility Control, default value: 0x02 */ #define REG_CBUS_MSC_COMPAT_CTRL 0x05c7#define BIT_CBUS_MSC_COMPAT_CTRL_XDEVCAP_EN BIT(7)#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_MSC_ON_CBUS BIT(6)#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_DDC_ON_CBUS BIT(5)#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_GET_DDC_ERRORCODE BIT(3)#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_GET_VS1_ERRORCODE BIT(2)/* CBUS3 Converter Control, default value: 0x24 */ #define REG_CBUS3_CNVT 0x05dc#define MSK_CBUS3_CNVT_CBUS3_RETRYLMT 0xf0#define MSK_CBUS3_CNVT_CBUS3_PEERTOUT_SEL 0x0c#define BIT_CBUS3_CNVT_TEARCBUS_EN BIT(1)#define BIT_CBUS3_CNVT_CBUS3CNVT_EN BIT(0)/* Discovery Control1, default value: 0x24 */ #define REG_DISC_CTRL1 0x05e0#define BIT_DISC_CTRL1_CBUS_INTR_EN BIT(7)#define BIT_DISC_CTRL1_HB_ONLY BIT(6)#define MSK_DISC_CTRL1_DISC_ATT 0x30#define MSK_DISC_CTRL1_DISC_CYC 0x0c#define BIT_DISC_CTRL1_DISC_EN BIT(0)#define VAL_PUP_OFF 0#define VAL_PUP_20K 1#define VAL_PUP_5K 2/* Discovery Control4, default value: 0x80 */ #define REG_DISC_CTRL4 0x05e3#define MSK_DISC_CTRL4_CBUSDISC_PUP_SEL 0xc0#define MSK_DISC_CTRL4_CBUSIDLE_PUP_SEL 0x30#define VAL_DISC_CTRL4(pup_disc, pup_idle) (((pup_disc) << 6) | (pup_idle << 4))/* Discovery Control5, default value: 0x03 */ #define REG_DISC_CTRL5 0x05e4#define BIT_DISC_CTRL5_DSM_OVRIDE BIT(3)#define MSK_DISC_CTRL5_CBUSMHL_PUP_SEL 0x03/* Discovery Control8, default value: 0x81 */ #define REG_DISC_CTRL8 0x05e7#define BIT_DISC_CTRL8_NOMHLINT_CLR_BYPASS BIT(7)#define BIT_DISC_CTRL8_DELAY_CBUS_INTR_EN BIT(0)/* Discovery Control9, default value: 0x54 */ #define REG_DISC_CTRL9 0x05e8#define BIT_DISC_CTRL9_MHL3_RSEN_BYP BIT(7)#define BIT_DISC_CTRL9_MHL3DISC_EN BIT(6)#define BIT_DISC_CTRL9_WAKE_DRVFLT BIT(4)#define BIT_DISC_CTRL9_NOMHL_EST BIT(3)#define BIT_DISC_CTRL9_DISC_PULSE_PROCEED BIT(2)#define BIT_DISC_CTRL9_WAKE_PULSE_BYPASS BIT(1)#define BIT_DISC_CTRL9_VBUS_OUTPUT_CAPABILITY_SRC BIT(0)/* Discovery Status1, default value: 0x00 */ #define REG_DISC_STAT1 0x05eb#define BIT_DISC_STAT1_PSM_OVRIDE BIT(5)#define MSK_DISC_STAT1_DISC_SM 0x0f/* Discovery Status2, default value: 0x00 */ #define REG_DISC_STAT2 0x05ec#define BIT_DISC_STAT2_CBUS_OE_POL BIT(6)#define BIT_DISC_STAT2_CBUS_SATUS BIT(5)#define BIT_DISC_STAT2_RSEN BIT(4)#define MSK_DISC_STAT2_MHL_VRSN 0x0c#define VAL_DISC_STAT2_DEFAULT 0x00#define VAL_DISC_STAT2_MHL1_2 0x04#define VAL_DISC_STAT2_MHL3 0x08#define VAL_DISC_STAT2_RESERVED 0x0c#define MSK_DISC_STAT2_RGND 0x03#define VAL_RGND_OPEN 0x00#define VAL_RGND_2K 0x01#define VAL_RGND_1K 0x02#define VAL_RGND_SHORT 0x03/* Interrupt CBUS_reg1 INTR0, default value: 0x00 */ #define REG_CBUS_DISC_INTR0 0x05ed#define BIT_RGND_READY_INT BIT(6)#define BIT_CBUS_MHL12_DISCON_INT BIT(5)#define BIT_CBUS_MHL3_DISCON_INT BIT(4)#define BIT_NOT_MHL_EST_INT BIT(3)#define BIT_MHL_EST_INT BIT(2)#define BIT_MHL3_EST_INT BIT(1)#define VAL_CBUS_MHL_DISCON (BIT_CBUS_MHL12_DISCON_INT \/* Interrupt CBUS_reg1 INTR0 Mask, default value: 0x00 */ #define REG_CBUS_DISC_INTR0_MASK 0x05ee#endif /* __SIL_SII8620_H__ */
Messung V0.5 C=91 H=94 G=92
¤ Dauer der Verarbeitung: 0.13 Sekunden
¤ *© Formatika GbR, Deutschland
