/** * struct iwl_ltr_config_cmd - configures the LTR * @flags: See &enum iwl_ltr_config_flags * @static_long: static LTR Long register value. * @static_short: static LTR Short register value. * @ltr_cfg_values: LTR parameters table values (in usec) in following order: * TX, RX, Short Idle, Long Idle. Used only if %LTR_CFG_FLAG_UPDATE_VALUES * is set. * @ltr_short_idle_timeout: LTR Short Idle timeout (in usec). Used only if * %LTR_CFG_FLAG_UPDATE_VALUES is set.
*/ struct iwl_ltr_config_cmd {
__le32 flags;
__le32 static_long;
__le32 static_short;
__le32 ltr_cfg_values[LTR_VALID_STATES_NUM];
__le32 ltr_short_idle_timeout;
} __packed; /* LTR_CAPABLE_API_S_VER_2 */
/* Radio LP RX Energy Threshold measured in dBm */ #define POWER_LPRX_RSSI_THRESHOLD 75 #define POWER_LPRX_RSSI_THRESHOLD_MAX 94 #define POWER_LPRX_RSSI_THRESHOLD_MIN 30
/** * enum iwl_power_flags - masks for power table command flags * @POWER_FLAGS_POWER_SAVE_ENA_MSK: '1' Allow to save power by turning off * receiver and transmitter. '0' - does not allow. * @POWER_FLAGS_POWER_MANAGEMENT_ENA_MSK: '0' Driver disables power management, * '1' Driver enables PM (use rest of parameters) * @POWER_FLAGS_SKIP_OVER_DTIM_MSK: '0' PM have to walk up every DTIM, * '1' PM could sleep over DTIM till listen Interval. * @POWER_FLAGS_SNOOZE_ENA_MSK: Enable snoozing only if uAPSD is enabled and all * access categories are both delivery and trigger enabled. * @POWER_FLAGS_BT_SCO_ENA: Enable BT SCO coex only if uAPSD and * PBW Snoozing enabled * @POWER_FLAGS_ADVANCE_PM_ENA_MSK: Advanced PM (uAPSD) enable mask * @POWER_FLAGS_LPRX_ENA_MSK: Low Power RX enable. * @POWER_FLAGS_UAPSD_MISBEHAVING_ENA_MSK: AP/GO's uAPSD misbehaving * detection enablement * @POWER_FLAGS_ENABLE_SMPS_MSK: SMPS is allowed for this vif
*/ enum iwl_power_flags {
POWER_FLAGS_POWER_SAVE_ENA_MSK = BIT(0),
POWER_FLAGS_POWER_MANAGEMENT_ENA_MSK = BIT(1),
POWER_FLAGS_SKIP_OVER_DTIM_MSK = BIT(2),
POWER_FLAGS_SNOOZE_ENA_MSK = BIT(5),
POWER_FLAGS_BT_SCO_ENA = BIT(8),
POWER_FLAGS_ADVANCE_PM_ENA_MSK = BIT(9),
POWER_FLAGS_LPRX_ENA_MSK = BIT(11),
POWER_FLAGS_UAPSD_MISBEHAVING_ENA_MSK = BIT(12),
POWER_FLAGS_ENABLE_SMPS_MSK = BIT(14),
};
#define IWL_POWER_VEC_SIZE 5
/** * struct iwl_powertable_cmd - legacy power command. Beside old API support this * is used also with a new power API for device wide power settings. * POWER_TABLE_CMD = 0x77 (command, has simple generic response) * * @flags: Power table command flags from POWER_FLAGS_* * @keep_alive_seconds: Keep alive period in seconds. Default - 25 sec. * Minimum allowed:- 3 * DTIM. Keep alive period must be * set regardless of power scheme or current power state. * FW use this value also when PM is disabled. * @debug_flags: debug flags * @rx_data_timeout: Minimum time (usec) from last Rx packet for AM to * PSM transition - legacy PM * @tx_data_timeout: Minimum time (usec) from last Tx packet for AM to * PSM transition - legacy PM * @sleep_interval: not in use * @skip_dtim_periods: Number of DTIM periods to skip if Skip over DTIM flag * is set. For example, if it is required to skip over * one DTIM, this value need to be set to 2 (DTIM periods). * @lprx_rssi_threshold: Signal strength up to which LP RX can be enabled. * Default: 80dbm
*/ struct iwl_powertable_cmd { /* PM_POWER_TABLE_CMD_API_S_VER_6 */
__le16 flags;
u8 keep_alive_seconds;
u8 debug_flags;
__le32 rx_data_timeout;
__le32 tx_data_timeout;
__le32 sleep_interval[IWL_POWER_VEC_SIZE];
__le32 skip_dtim_periods;
__le32 lprx_rssi_threshold;
} __packed;
/** * enum iwl_device_power_flags - masks for device power command flags * @DEVICE_POWER_FLAGS_POWER_SAVE_ENA_MSK: * '1' Allow to save power by turning off * receiver and transmitter. '0' - does not allow. * @DEVICE_POWER_FLAGS_ALLOW_MEM_RETENTION_MSK: * Device Retention indication, '1' indicate retention is enabled. * @DEVICE_POWER_FLAGS_NO_SLEEP_TILL_D3_MSK: * Prevent power save until entering d3 is completed. * @DEVICE_POWER_FLAGS_32K_CLK_VALID_MSK: * 32Khz external slow clock valid indication, '1' indicate cloack is * valid.
*/ enum iwl_device_power_flags {
DEVICE_POWER_FLAGS_POWER_SAVE_ENA_MSK = BIT(0),
DEVICE_POWER_FLAGS_ALLOW_MEM_RETENTION_MSK = BIT(1),
DEVICE_POWER_FLAGS_NO_SLEEP_TILL_D3_MSK = BIT(7),
DEVICE_POWER_FLAGS_32K_CLK_VALID_MSK = BIT(12),
};
/** * struct iwl_mac_power_cmd - New power command containing uAPSD support * MAC_PM_POWER_TABLE = 0xA9 (command, has simple generic response) * @id_and_color: MAC contex identifier, &enum iwl_ctxt_id_and_color * @flags: Power table command flags from POWER_FLAGS_* * @keep_alive_seconds: Keep alive period in seconds. Default - 25 sec. * Minimum allowed:- 3 * DTIM. Keep alive period must be * set regardless of power scheme or current power state. * FW use this value also when PM is disabled. * @rx_data_timeout: Minimum time (usec) from last Rx packet for AM to * PSM transition - legacy PM * @tx_data_timeout: Minimum time (usec) from last Tx packet for AM to * PSM transition - legacy PM * @skip_dtim_periods: Number of DTIM periods to skip if Skip over DTIM flag * is set. For example, if it is required to skip over * one DTIM, this value need to be set to 2 (DTIM periods). * @rx_data_timeout_uapsd: Minimum time (usec) from last Rx packet for AM to * PSM transition - uAPSD * @tx_data_timeout_uapsd: Minimum time (usec) from last Tx packet for AM to * PSM transition - uAPSD * @lprx_rssi_threshold: Signal strength up to which LP RX can be enabled. * Default: 80dbm * @snooze_interval: Maximum time between attempts to retrieve buffered data * from the AP [msec] * @snooze_window: A window of time in which PBW snoozing insures that all * packets received. It is also the minimum time from last * received unicast RX packet, before client stops snoozing * for data. [msec] * @snooze_step: TBD * @qndp_tid: TID client shall use for uAPSD QNDP triggers * @uapsd_ac_flags: Set trigger-enabled and delivery-enabled indication for * each corresponding AC. * Use IEEE80211_WMM_IE_STA_QOSINFO_AC* for correct values. * @uapsd_max_sp: Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct * values. * @heavy_tx_thld_packets: TX threshold measured in number of packets * @heavy_rx_thld_packets: RX threshold measured in number of packets * @heavy_tx_thld_percentage: TX threshold measured in load's percentage * @heavy_rx_thld_percentage: RX threshold measured in load's percentage * @limited_ps_threshold: (unused) * @reserved: reserved (padding)
*/ struct iwl_mac_power_cmd { /* CONTEXT_DESC_API_T_VER_1 */
__le32 id_and_color;
/* * struct iwl_uapsd_misbehaving_ap_notif - FW sends this notification when * associated AP is identified as improperly implementing uAPSD protocol. * PSM_UAPSD_AP_MISBEHAVING_NOTIFICATION = 0x78 * @sta_id: index of station in uCode's station table - associated AP ID in * this context.
*/ struct iwl_uapsd_misbehaving_ap_notif {
__le32 sta_id;
u8 mac_id;
u8 reserved[3];
} __packed;
/** * struct iwl_dev_tx_power_common - Common part of the TX power reduction cmd * @set_mode: see &enum iwl_dev_tx_power_cmd_mode * @link_id: id of the link ctx for which we are reducing TX power. * For version 9 / 10, this is the link id. For earlier versions, it is * the mac id. * @pwr_restriction: TX power restriction in 1/8 dBms.
*/ struct iwl_dev_tx_power_common {
__le32 set_mode;
__le32 link_id;
__le16 pwr_restriction;
} __packed;
/** * struct iwl_dev_tx_power_cmd_v3 - TX power reduction command version 3 * @per_chain: per chain restrictions
*/ struct iwl_dev_tx_power_cmd_v3 {
__le16 per_chain[IWL_NUM_CHAIN_TABLES][IWL_NUM_CHAIN_LIMITS][IWL_NUM_SUB_BANDS_V1];
} __packed; /* TX_REDUCED_POWER_API_S_VER_3 */
#define IWL_DEV_MAX_TX_POWER 0x7FFF
/** * struct iwl_dev_tx_power_cmd_v4 - TX power reduction command version 4 * @per_chain: per chain restrictions * @enable_ack_reduction: enable or disable close range ack TX power * reduction. * @reserved: reserved (padding)
*/ struct iwl_dev_tx_power_cmd_v4 {
__le16 per_chain[IWL_NUM_CHAIN_TABLES][IWL_NUM_CHAIN_LIMITS][IWL_NUM_SUB_BANDS_V1];
u8 enable_ack_reduction;
u8 reserved[3];
} __packed; /* TX_REDUCED_POWER_API_S_VER_4 */
/** * struct iwl_dev_tx_power_cmd_v5 - TX power reduction command version 5 * @per_chain: per chain restrictions * @enable_ack_reduction: enable or disable close range ack TX power * reduction. * @per_chain_restriction_changed: is per_chain_restriction has changed * from last command. used if set_mode is * IWL_TX_POWER_MODE_SET_SAR_TIMER. * note: if not changed, the command is used for keep alive only. * @reserved: reserved (padding) * @timer_period: timer in milliseconds. if expires FW will change to default * BIOS values. relevant if setMode is IWL_TX_POWER_MODE_SET_SAR_TIMER
*/ struct iwl_dev_tx_power_cmd_v5 {
__le16 per_chain[IWL_NUM_CHAIN_TABLES][IWL_NUM_CHAIN_LIMITS][IWL_NUM_SUB_BANDS_V1];
u8 enable_ack_reduction;
u8 per_chain_restriction_changed;
u8 reserved[2];
__le32 timer_period;
} __packed; /* TX_REDUCED_POWER_API_S_VER_5 */
/** * struct iwl_dev_tx_power_cmd_v8 - TX power reduction command version 8 * @per_chain: per chain restrictions * @enable_ack_reduction: enable or disable close range ack TX power * reduction. * @per_chain_restriction_changed: is per_chain_restriction has changed * from last command. used if set_mode is * IWL_TX_POWER_MODE_SET_SAR_TIMER. * note: if not changed, the command is used for keep alive only. * @reserved: reserved (padding) * @timer_period: timer in milliseconds. if expires FW will change to default * BIOS values. relevant if setMode is IWL_TX_POWER_MODE_SET_SAR_TIMER * @flags: reduce power flags. * @tpc_vlp_backoff_level: user backoff of UNII5,7 VLP channels in USA. * Not in use.
*/ struct iwl_dev_tx_power_cmd_v8 {
__le16 per_chain[IWL_NUM_CHAIN_TABLES_V2][IWL_NUM_CHAIN_LIMITS][IWL_NUM_SUB_BANDS_V2];
u8 enable_ack_reduction;
u8 per_chain_restriction_changed;
u8 reserved[2];
__le32 timer_period;
__le32 flags;
__le32 tpc_vlp_backoff_level;
} __packed; /* TX_REDUCED_POWER_API_S_VER_8 */
/* * @dev_24: device TX power restriction in 1/8 dBms * @dev_52_low: device TX power restriction upper band - low * @dev_52_high: device TX power restriction upper band - high
*/ struct iwl_dev_tx_power_cmd_per_band {
__le16 dev_24;
__le16 dev_52_low;
__le16 dev_52_high;
} __packed;
/** * struct iwl_dev_tx_power_cmd_v3_v8 - TX power reduction command (multiversion) * @per_band: per band restrictions * @common: common part of the command * @v3: version 3 part of the command * @v4: version 4 part of the command * @v5: version 5 part of the command * @v8: version 8 part of the command
*/ struct iwl_dev_tx_power_cmd_v3_v8 { struct iwl_dev_tx_power_common common; struct iwl_dev_tx_power_cmd_per_band per_band; union { struct iwl_dev_tx_power_cmd_v3 v3; struct iwl_dev_tx_power_cmd_v4 v4; struct iwl_dev_tx_power_cmd_v5 v5; struct iwl_dev_tx_power_cmd_v8 v8;
};
};
/** * struct iwl_dev_tx_power_cmd_v9 - TX power reduction cmd * @reserved: reserved (padding) * @per_chain: per chain restrictions * @per_chain_restriction_changed: is per_chain_restriction has changed * from last command. used if set_mode is * IWL_TX_POWER_MODE_SET_SAR_TIMER. * note: if not changed, the command is used for keep alive only. * @reserved1: reserved (padding) * @timer_period: timer in milliseconds. if expires FW will change to default * BIOS values. relevant if setMode is IWL_TX_POWER_MODE_SET_SAR_TIMER
*/ struct iwl_dev_tx_power_cmd_v9 {
__le16 reserved;
__le16 per_chain[IWL_NUM_CHAIN_LIMITS][IWL_NUM_SUB_BANDS_V1];
u8 per_chain_restriction_changed;
u8 reserved1[3];
__le32 timer_period;
} __packed; /* TX_REDUCED_POWER_API_S_VER_9 */
/** * struct iwl_dev_tx_power_cmd_v10 - TX power reduction cmd * @per_chain: per chain restrictions * @per_chain_restriction_changed: is per_chain_restriction has changed * from last command. used if set_mode is * IWL_TX_POWER_MODE_SET_SAR_TIMER. * note: if not changed, the command is used for keep alive only. * @reserved: reserved (padding) * @timer_period: timer in milliseconds. if expires FW will change to default * BIOS values. relevant if setMode is IWL_TX_POWER_MODE_SET_SAR_TIMER * @flags: reduce power flags.
*/ struct iwl_dev_tx_power_cmd_v10 {
__le16 per_chain[IWL_NUM_CHAIN_TABLES_V2][IWL_NUM_CHAIN_LIMITS][IWL_NUM_SUB_BANDS_V2];
u8 per_chain_restriction_changed;
u8 reserved;
__le32 timer_period;
__le32 flags;
} __packed; /* TX_REDUCED_POWER_API_S_VER_10 */
/* * struct iwl_dev_tx_power_cmd - TX power reduction command (multiversion) * @common: common part of the command * @v9: version 9 part of the command * @v10: version 10 part of the command
*/ struct iwl_dev_tx_power_cmd { struct iwl_dev_tx_power_common common; union { struct iwl_dev_tx_power_cmd_v9 v9; struct iwl_dev_tx_power_cmd_v10 v10;
};
} __packed; /* TX_REDUCED_POWER_API_S_VER_9_VER10 */
/** * enum iwl_geo_per_chain_offset_operation - type of operation * @IWL_PER_CHAIN_OFFSET_SET_TABLES: send the tables from the host to the FW. * @IWL_PER_CHAIN_OFFSET_GET_CURRENT_TABLE: retrieve the last configured table.
*/ enum iwl_geo_per_chain_offset_operation {
IWL_PER_CHAIN_OFFSET_SET_TABLES,
IWL_PER_CHAIN_OFFSET_GET_CURRENT_TABLE,
}; /* PER_CHAIN_OFFSET_OPERATION_E */
/** * struct iwl_per_chain_offset - embedded struct for PER_CHAIN_LIMIT_OFFSET_CMD. * @max_tx_power: maximum allowed tx power. * @chain_a: tx power offset for chain a. * @chain_b: tx power offset for chain b.
*/ struct iwl_per_chain_offset {
__le16 max_tx_power;
u8 chain_a;
u8 chain_b;
} __packed; /* PER_CHAIN_LIMIT_OFFSET_PER_CHAIN_S_VER_1 */
/** * struct iwl_geo_tx_power_profiles_cmd_v1 - struct for PER_CHAIN_LIMIT_OFFSET_CMD cmd. * @ops: operations, value from &enum iwl_geo_per_chain_offset_operation * @table: offset profile per band.
*/ struct iwl_geo_tx_power_profiles_cmd_v1 {
__le32 ops; struct iwl_per_chain_offset table[IWL_NUM_GEO_PROFILES][IWL_NUM_BANDS_PER_CHAIN_V1];
} __packed; /* PER_CHAIN_LIMIT_OFFSET_CMD_VER_1 */
/** * struct iwl_geo_tx_power_profiles_cmd_v2 - struct for PER_CHAIN_LIMIT_OFFSET_CMD cmd. * @ops: operations, value from &enum iwl_geo_per_chain_offset_operation * @table: offset profile per band. * @table_revision: 0 for not-South Korea, 1 for South Korea (the name is misleading)
*/ struct iwl_geo_tx_power_profiles_cmd_v2 {
__le32 ops; struct iwl_per_chain_offset table[IWL_NUM_GEO_PROFILES][IWL_NUM_BANDS_PER_CHAIN_V1];
__le32 table_revision;
} __packed; /* PER_CHAIN_LIMIT_OFFSET_CMD_VER_2 */
/** * struct iwl_geo_tx_power_profiles_cmd_v3 - struct for PER_CHAIN_LIMIT_OFFSET_CMD cmd. * @ops: operations, value from &enum iwl_geo_per_chain_offset_operation * @table: offset profile per band. * @table_revision: 0 for not-South Korea, 1 for South Korea (the name is misleading)
*/ struct iwl_geo_tx_power_profiles_cmd_v3 {
__le32 ops; struct iwl_per_chain_offset table[IWL_NUM_GEO_PROFILES][IWL_NUM_BANDS_PER_CHAIN_V2];
__le32 table_revision;
} __packed; /* PER_CHAIN_LIMIT_OFFSET_CMD_VER_3 */
/** * struct iwl_geo_tx_power_profiles_cmd_v4 - struct for PER_CHAIN_LIMIT_OFFSET_CMD cmd. * @ops: operations, value from &enum iwl_geo_per_chain_offset_operation * @table: offset profile per band. * @table_revision: 0 for not-South Korea, 1 for South Korea (the name is misleading)
*/ struct iwl_geo_tx_power_profiles_cmd_v4 {
__le32 ops; struct iwl_per_chain_offset table[IWL_NUM_GEO_PROFILES_V3][IWL_NUM_BANDS_PER_CHAIN_V1];
__le32 table_revision;
} __packed; /* PER_CHAIN_LIMIT_OFFSET_CMD_VER_4 */
/** * struct iwl_geo_tx_power_profiles_cmd_v5 - struct for PER_CHAIN_LIMIT_OFFSET_CMD cmd. * @ops: operations, value from &enum iwl_geo_per_chain_offset_operation * @table: offset profile per band. * @table_revision: 0 for not-South Korea, 1 for South Korea (the name is misleading)
*/ struct iwl_geo_tx_power_profiles_cmd_v5 {
__le32 ops; struct iwl_per_chain_offset table[IWL_NUM_GEO_PROFILES_V3][IWL_NUM_BANDS_PER_CHAIN_V2];
__le32 table_revision;
} __packed; /* PER_CHAIN_LIMIT_OFFSET_CMD_VER_5 */
/** * struct iwl_geo_tx_power_profiles_resp - response to PER_CHAIN_LIMIT_OFFSET_CMD cmd * @profile_idx: current geo profile in use
*/ struct iwl_geo_tx_power_profiles_resp {
__le32 profile_idx;
} __packed; /* PER_CHAIN_LIMIT_OFFSET_RSP */
/** * enum iwl_ppag_flags - PPAG enable masks * @IWL_PPAG_ETSI_MASK: enable PPAG in ETSI * @IWL_PPAG_CHINA_MASK: enable PPAG in China * @IWL_PPAG_ETSI_LPI_UHB_MASK: enable LPI in ETSI for UHB * @IWL_PPAG_ETSI_VLP_UHB_MASK: enable VLP in ETSI for UHB * @IWL_PPAG_ETSI_SP_UHB_MASK: enable SP in ETSI for UHB * @IWL_PPAG_USA_LPI_UHB_MASK: enable LPI in USA for UHB * @IWL_PPAG_USA_VLP_UHB_MASK: enable VLP in USA for UHB * @IWL_PPAG_USA_SP_UHB_MASK: enable SP in USA for UHB * @IWL_PPAG_CANADA_LPI_UHB_MASK: enable LPI in CANADA for UHB * @IWL_PPAG_CANADA_VLP_UHB_MASK: enable VLP in CANADA for UHB * @IWL_PPAG_CANADA_SP_UHB_MASK: enable SP in CANADA for UHB
*/ enum iwl_ppag_flags {
IWL_PPAG_ETSI_MASK = BIT(0),
IWL_PPAG_CHINA_MASK = BIT(1),
IWL_PPAG_ETSI_LPI_UHB_MASK = BIT(2),
IWL_PPAG_ETSI_VLP_UHB_MASK = BIT(3),
IWL_PPAG_ETSI_SP_UHB_MASK = BIT(4),
IWL_PPAG_USA_LPI_UHB_MASK = BIT(5),
IWL_PPAG_USA_VLP_UHB_MASK = BIT(6),
IWL_PPAG_USA_SP_UHB_MASK = BIT(7),
IWL_PPAG_CANADA_LPI_UHB_MASK = BIT(8),
IWL_PPAG_CANADA_VLP_UHB_MASK = BIT(9),
IWL_PPAG_CANADA_SP_UHB_MASK = BIT(10),
};
/** * union iwl_ppag_table_cmd - union for all versions of PPAG command * @v1: command version 1 structure. * @v2: command version from 2 to 6 are same structure as v2. * but has a different format of the flags bitmap * @v3: command version 7 structure. * @v1.flags: values from &enum iwl_ppag_flags * @v1.gain: table of antenna gain values per chain and sub-band * @v1.reserved: reserved * @v2.flags: values from &enum iwl_ppag_flags * @v2.gain: table of antenna gain values per chain and sub-band * @v3.ppag_config_info: see @struct bios_value_u32 * @v3.gain: table of antenna gain values per chain and sub-band * @v3.reserved: reserved
*/ union iwl_ppag_table_cmd { struct {
__le32 flags;
s8 gain[IWL_NUM_CHAIN_LIMITS][IWL_NUM_SUB_BANDS_V1];
s8 reserved[2];
} __packed v1; /* PER_PLAT_ANTENNA_GAIN_CMD_API_S_VER_1 */ struct {
__le32 flags;
s8 gain[IWL_NUM_CHAIN_LIMITS][IWL_NUM_SUB_BANDS_V2];
s8 reserved[2];
} __packed v2; /* PER_PLAT_ANTENNA_GAIN_CMD_API_S_VER_2, VER3, VER4, * VER5, VER6
*/ struct { struct bios_value_u32 ppag_config_info;
s8 gain[IWL_NUM_CHAIN_LIMITS][IWL_NUM_SUB_BANDS_V2];
s8 reserved[2];
} __packed v3; /* PER_PLAT_ANTENNA_GAIN_CMD_API_S_VER_7 */
} __packed;
/** * struct iwl_sar_offset_mapping_cmd - struct for SAR_OFFSET_MAPPING_TABLE_CMD * @offset_map: mapping a mcc to a geo sar group * @reserved: reserved
*/ struct iwl_sar_offset_mapping_cmd {
u8 offset_map[MCC_TO_SAR_OFFSET_TABLE_ROW_SIZE]
[MCC_TO_SAR_OFFSET_TABLE_COL_SIZE];
__le16 reserved;
} __packed; /*SAR_OFFSET_MAPPING_TABLE_CMD_API_S*/
/** * struct iwl_beacon_filter_cmd * REPLY_BEACON_FILTERING_CMD = 0xd2 (command) * @bf_energy_delta: Used for RSSI filtering, if in 'normal' state. Send beacon * to driver if delta in Energy values calculated for this and last * passed beacon is greater than this threshold. Zero value means that * the Energy change is ignored for beacon filtering, and beacon will * not be forced to be sent to driver regardless of this delta. Typical * energy delta 5dB. * @bf_roaming_energy_delta: Used for RSSI filtering, if in 'roaming' state. * Send beacon to driver if delta in Energy values calculated for this * and last passed beacon is greater than this threshold. Zero value * means that the Energy change is ignored for beacon filtering while in * Roaming state, typical energy delta 1dB. * @bf_roaming_state: Used for RSSI filtering. If absolute Energy values * calculated for current beacon is less than the threshold, use * Roaming Energy Delta Threshold, otherwise use normal Energy Delta * Threshold. Typical energy threshold is -72dBm. * @bf_temp_threshold: This threshold determines the type of temperature * filtering (Slow or Fast) that is selected (Units are in Celsius): * If the current temperature is above this threshold - Fast filter * will be used, If the current temperature is below this threshold - * Slow filter will be used. * @bf_temp_fast_filter: Send Beacon to driver if delta in temperature values * calculated for this and the last passed beacon is greater than this * threshold. Zero value means that the temperature change is ignored for * beacon filtering; beacons will not be forced to be sent to driver * regardless of whether its temperature has been changed. * @bf_temp_slow_filter: Send Beacon to driver if delta in temperature values * calculated for this and the last passed beacon is greater than this * threshold. Zero value means that the temperature change is ignored for * beacon filtering; beacons will not be forced to be sent to driver * regardless of whether its temperature has been changed. * @bf_enable_beacon_filter: 1, beacon filtering is enabled; 0, disabled. * @bf_debug_flag: beacon filtering debug configuration * @bf_escape_timer: Send beacons to to driver if no beacons were passed * for a specific period of time. Units: Beacons. * @ba_escape_timer: Fully receive and parse beacon if no beacons were passed * for a longer period of time then this escape-timeout. Units: Beacons. * @ba_enable_beacon_abort: 1, beacon abort is enabled; 0, disabled. * @bf_threshold_absolute_low: See below. * @bf_threshold_absolute_high: Send Beacon to driver if Energy value calculated * for this beacon crossed this absolute threshold. For the 'Increase' * direction the bf_energy_absolute_low[i] is used. For the 'Decrease' * direction the bf_energy_absolute_high[i] is used. Zero value means * that this specific threshold is ignored for beacon filtering, and * beacon will not be forced to be sent to driver due to this setting.
*/ struct iwl_beacon_filter_cmd {
__le32 bf_energy_delta;
__le32 bf_roaming_energy_delta;
__le32 bf_roaming_state;
__le32 bf_temp_threshold;
__le32 bf_temp_fast_filter;
__le32 bf_temp_slow_filter;
__le32 bf_enable_beacon_filter;
__le32 bf_debug_flag;
__le32 bf_escape_timer;
__le32 ba_escape_timer;
__le32 ba_enable_beacon_abort;
__le32 bf_threshold_absolute_low[2];
__le32 bf_threshold_absolute_high[2];
} __packed; /* BEACON_FILTER_CONFIG_API_S_VER_4 */
/** * struct iwl_txpower_constraints_cmd * AP_TX_POWER_CONSTRAINTS_CMD * Used for VLP/LPI/AFC Access Point power constraints for 6GHz channels * @link_id: linkId * @ap_type: see &enum iwl_ap_type * @eirp_pwr: 8-bit 2s complement signed integer in the range * -64 dBm to 63 dBm with a 0.5 dB step * default &DEFAULT_TPE_TX_POWER (no maximum limit) * @psd_pwr: 8-bit 2s complement signed integer in the range * -63.5 to +63 dBm/MHz with a 0.5 step * value - 128 indicates that the corresponding 20 * MHz channel cannot be used for transmission. * value +127 indicates that no maximum PSD limit * is specified for the corresponding 20 MHz channel * default &DEFAULT_TPE_TX_POWER (no maximum limit) * @reserved: reserved (padding)
*/ struct iwl_txpower_constraints_cmd {
__le16 link_id;
__le16 ap_type;
__s8 eirp_pwr[IWL_MAX_TX_EIRP_PWR_MAX_SIZE];
__s8 psd_pwr[IWL_MAX_TX_EIRP_PSD_PWR_MAX_SIZE];
u8 reserved[3];
} __packed; /* PHY_AP_TX_POWER_CONSTRAINTS_CMD_API_S_VER_1 */ #endif/* __iwl_fw_api_power_h__ */
Messung V0.5
¤ Dauer der Verarbeitung: 0.17 Sekunden
(vorverarbeitet)
¤
Die Informationen auf dieser Webseite wurden
nach bestem Wissen sorgfältig zusammengestellt. Es wird jedoch weder Vollständigkeit, noch Richtigkeit,
noch Qualität der bereit gestellten Informationen zugesichert.
Bemerkung:
Die farbliche Syntaxdarstellung und die Messung sind noch experimentell.
