// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "qcs8300.dtsi"
#include "qcs8300-pmics.dtsi"
/ {
model = "Qualcomm Technologies, Inc. QCS8300 Ride";
compatible = "qcom,qcs8300-ride", "qcom,qcs8300";
chassis-type = "embedded";
aliases {
serial0 = &uart7;
};
chosen {
stdout-path = "serial0:115200n8";
};
regulator-usb2-vbus {
compatible = "regulator-fixed";
regulator-name = "USB2_VBUS";
gpio = <&pmm8650au_1_gpios 7 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&usb2_en>;
pinctrl-names = "default";
enable-active-high;
regulator-always-on;
};
};
&apps_rsc {
regulators-0 {
compatible = "qcom,pmm8654au-rpmh-regulators";
qcom,pmic-id = "a";
vreg_s4a: smps4 {
regulator-name = "vreg_s4a";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_s9a: smps9 {
regulator-name = "vreg_s9a";
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l3a: ldo3 {
regulator-name = "vreg_l3a";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l4a: ldo4 {
regulator-name = "vreg_l4a";
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <912000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l5a: ldo5 {
regulator-name = "vreg_l5a";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l6a: ldo6 {
regulator-name = "vreg_l6a";
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <912000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l7a: ldo7 {
regulator-name = "vreg_l7a";
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <912000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l8a: ldo8 {
regulator-name = "vreg_l8a";
regulator-min-microvolt = <2504000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l9a: ldo9 {
regulator-name = "vreg_l9a";
regulator-min-microvolt = <2970000>;
regulator-max-microvolt = <3072000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
};
regulators-1 {
compatible = "qcom,pmm8654au-rpmh-regulators";
qcom,pmic-id = "c";
vreg_s5c: smps5 {
regulator-name = "vreg_s5c";
regulator-min-microvolt = <1104000>;
regulator-max-microvolt = <1104000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l1c: ldo1 {
regulator-name = "vreg_l1c";
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <500000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l2c: ldo2 {
regulator-name = "vreg_l2c";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <904000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l4c: ldo4 {
regulator-name = "vreg_l4c";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l6c: ldo6 {
regulator-name = "vreg_l6c";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l7c: ldo7 {
regulator-name = "vreg_l7c";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l8c: ldo8 {
regulator-name = "vreg_l8c";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
vreg_l9c: ldo9 {
regulator-name = "vreg_l9c";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-allow-set-load;
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
RPMH_REGULATOR_MODE_HPM>;
};
};
};
ðernet0 {
phy-mode = "2500base-x";
phy-handle = <&phy0>;
pinctrl-0 = <ðernet0_default>;
pinctrl-names = "default";
snps,mtl-rx-config = <&mtl_rx_setup>;
snps,mtl-tx-config = <&mtl_tx_setup>;
snps,ps-speed = <1000>;
status = "okay";
mdio {
compatible = "snps,dwmac-mdio";
#address-cells = <1>;
#size-cells = <0>;
phy0: phy@8 {
compatible = "ethernet-phy-id31c3.1c33";
reg = <0x8>;
device_type = "ethernet-phy";
interrupts-extended = <&tlmm 4 IRQ_TYPE_EDGE_FALLING>;
reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
reset-assert-us = <11000>;
reset-deassert-us = <70000>;
};
};
mtl_rx_setup: rx-queues-config {
snps,rx-queues-to-use = <4>;
snps,rx-sched-sp;
queue0 {
snps,dcb-algorithm;
snps,map-to-dma-channel = <0x0>;
snps,route-up;
snps,priority = <0x1>;
};
queue1 {
snps,dcb-algorithm;
snps,map-to-dma-channel = <0x1>;
snps,route-ptp;
};
queue2 {
snps,avb-algorithm;
snps,map-to-dma-channel = <0x2>;
snps,route-avcp;
};
queue3 {
snps,avb-algorithm;
snps,map-to-dma-channel = <0x3>;
snps,priority = <0xc>;
};
};
mtl_tx_setup: tx-queues-config {
snps,tx-queues-to-use = <4>;
queue0 {
snps,dcb-algorithm;
};
queue1 {
snps,dcb-algorithm;
};
queue2 {
snps,avb-algorithm;
snps,send_slope = <0x1000>;
snps,idle_slope = <0x1000>;
snps,high_credit = <0x3e800>;
snps,low_credit = <0xffc18000>;
};
queue3 {
snps,avb-algorithm;
snps,send_slope = <0x1000>;
snps,idle_slope = <0x1000>;
snps,high_credit = <0x3e800>;
snps,low_credit = <0xffc18000>;
};
};
};
&pmm8650au_1_gpios {
usb2_en: usb2-en-state {
pins = "gpio7";
function = "normal";
output-enable;
power-source = <0>;
};
};
&iris {
status = "okay";
};
&qupv3_id_0 {
status = "okay";
};
&remoteproc_adsp {
firmware-name = "qcom/qcs8300/adsp.mbn";
status = "okay";
};
&remoteproc_cdsp {
firmware-name = "qcom/qcs8300/cdsp0.mbn";
status = "okay";
};
&remoteproc_gpdsp {
firmware-name = "qcom/qcs8300/gpdsp0.mbn";
status = "okay";
};
&serdes0 {
phy-supply = <&vreg_l5a>;
status = "okay";
};
&tlmm {
ethernet0_default: ethernet0-default-state {
ethernet0_mdc: ethernet0-mdc-pins {
pins = "gpio5";
function = "emac0_mdc";
drive-strength = <16>;
bias-pull-up;
};
ethernet0_mdio: ethernet0-mdio-pins {
pins = "gpio6";
function = "emac0_mdio";
drive-strength = <16>;
bias-pull-up;
};
};
};
&uart7 {
status = "okay";
};
&ufs_mem_hc {
reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
vcc-supply = <&vreg_l8a>;
vcc-max-microamp = <1100000>;
vccq-supply = <&vreg_l4c>;
vccq-max-microamp = <1200000>;
status = "okay";
};
&ufs_mem_phy {
vdda-phy-supply = <&vreg_l4a>;
vdda-pll-supply = <&vreg_l5a>;
status = "okay";
};
&usb_1_hsphy {
vdda-pll-supply = <&vreg_l7a>;
vdda18-supply = <&vreg_l7c>;
vdda33-supply = <&vreg_l9a>;
status = "okay";
};
&usb_2_hsphy {
vdda-pll-supply = <&vreg_l7a>;
vdda18-supply = <&vreg_l7c>;
vdda33-supply = <&vreg_l9a>;
status = "okay";
};
&usb_qmpphy {
vdda-phy-supply = <&vreg_l7a>;
vdda-pll-supply = <&vreg_l5a>;
status = "okay";
};
&usb_1 {
status = "okay";
};
&usb_1_dwc3 {
dr_mode = "peripheral";
};
&usb_2 {
status = "okay";
};
&usb_2_dwc3 {
dr_mode = "host";
};
[ Dauer der Verarbeitung: 0.2 Sekunden
(vorverarbeitet)
]
