/*
* Cobalt Qube/Raq PCI support
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
* Copyright (C) 1995, 1996, 1997, 2002, 2003 by Ralf Baechle
* Copyright (C) 2001, 2002, 2003 by Liam Davies (ldavies@agile.tv)
*/
#include <linux/types.h>
#include <linux/pci.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <
asm/io.h>
#include <
asm/gt64120.h>
#include <cobalt.h>
#include <irq.h>
/*
* PCI slot numbers
*/
#define COBALT_PCICONF_CPU 0x06
#define COBALT_PCICONF_ETH0 0x07
#define COBALT_PCICONF_RAQSCSI 0x08
#define COBALT_PCICONF_VIA 0x09
#define COBALT_PCICONF_PCISLOT 0x0A
#define COBALT_PCICONF_ETH1 0x0C
/*
* The Cobalt board ID information. The boards have an ID number wired
* into the VIA that is available in the high nibble of register 94.
*/
#define VIA_COBALT_BRD_ID_REG 0x94
#define VIA_COBALT_BRD_REG_to_ID(reg) ((
unsigned char)(reg) >> 4)
/*
* Default value of PCI Class Code on GT64111 is PCI_CLASS_MEMORY_OTHER (0x0580)
* instead of PCI_CLASS_BRIDGE_HOST (0x0600). Galileo explained this choice in
* document "GT-64111 System Controller for RC4640, RM523X and VR4300 CPUs",
* section "6.5.3 PCI Autoconfiguration at RESET":
*
* Some PCs refuse to configure host bridges if they are found plugged into
* a PCI slot (ask the BIOS vendors why...). The "Memory Controller" Class
* Code does not cause a problem for these non-compliant BIOSes, so we used
* this as the default in the GT-64111.
*
* So fix the incorrect default value of PCI Class Code. More details are on:
* https://lore.kernel.org/r/20211102154831.xtrlgrmrizl5eidl@pali/
* https://lore.kernel.org/r/20211102150201.GA11675@alpha.franken.de/
*/
static void qube_raq_galileo_early_fixup(
struct pci_dev *dev)
{
if (dev->devfn == PCI_DEVFN(0, 0) &&
(dev->
class >> 8) == PCI_CLASS_MEMORY_OTHER) {
dev->
class = (PCI_CLASS_BRIDGE_HOST << 8) | (dev->
class & 0xff);
printk(KERN_INFO
"Galileo: fixed bridge class\n");
}
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_MARVELL, PCI_DEVICE_ID_MARVELL_GT64111,
qube_raq_galileo_early_fixup);
static void qube_raq_via_bmIDE_fixup(
struct pci_dev *dev)
{
unsigned short cfgword;
unsigned char lt;
/* Enable Bus Mastering and fast back to back. */
pci_read_config_word(dev, PCI_COMMAND, &cfgword);
cfgword |= (PCI_COMMAND_FAST_BACK | PCI_COMMAND_MASTER);
pci_write_config_word(dev, PCI_COMMAND, cfgword);
/* Enable both ide interfaces. ROM only enables primary one. */
pci_write_config_byte(dev, 0x40, 0xb);
/* Set latency timer to reasonable value. */
pci_read_config_byte(dev, PCI_LATENCY_TIMER, <);
if (lt < 64)
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 8);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1,
qube_raq_via_bmIDE_fixup);
static void qube_raq_galileo_fixup(
struct pci_dev *dev)
{
if (dev->devfn != PCI_DEVFN(0, 0))
return;
/* Fix PCI latency-timer and cache-line-size values in Galileo
* host bridge.
*/
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 8);
/*
* The code described by the comment below has been removed
* as it causes bus mastering by the Ethernet controllers
* to break under any kind of network load. We always set
* the retry timeouts to their maximum.
*
* --x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--
*
* On all machines prior to Q2, we had the STOP line disconnected
* from Galileo to VIA on PCI. The new Galileo does not function
* correctly unless we have it connected.
*
* Therefore we must set the disconnect/retry cycle values to
* something sensible when using the new Galileo.
*/
printk(KERN_INFO
"Galileo: revision %u\n", dev->revision);
#if 0
if (dev->revision >= 0x10) {
/* New Galileo, assumes PCI stop line to VIA is connected. */
GT_WRITE(GT_PCI0_TOR_OFS, 0x4020);
}
else if (dev->revision == 0x1 || dev->revision == 0x2)
#endif
{
signed int timeo;
/* XXX WE MUST DO THIS ELSE GALILEO LOCKS UP! -DaveM */
timeo = GT_READ(GT_PCI0_TOR_OFS);
/* Old Galileo, assumes PCI STOP line to VIA is disconnected. */
GT_WRITE(GT_PCI0_TOR_OFS,
(0xff << 16) |
/* retry count */
(0xff << 8) |
/* timeout 1 */
0xff);
/* timeout 0 */
/* enable PCI retry exceeded interrupt */
GT_WRITE(GT_INTRMASK_OFS, GT_INTR_RETRYCTR0_MSK | GT_READ(GT_INTRMASK_OFS));
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL, PCI_DEVICE_ID_MARVELL_GT64111,
qube_raq_galileo_fixup);
int cobalt_board_id;
static void qube_raq_via_board_id_fixup(
struct pci_dev *dev)
{
u8 id;
int retval;
retval = pci_read_config_byte(dev, VIA_COBALT_BRD_ID_REG, &id);
if (retval) {
panic(
"Cannot read board ID");
return;
}
cobalt_board_id = VIA_COBALT_BRD_REG_to_ID(id);
printk(KERN_INFO
"Cobalt board ID: %d\n", cobalt_board_id);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0,
qube_raq_via_board_id_fixup);
static char irq_tab_qube1[] = {
[COBALT_PCICONF_CPU] = 0,
[COBALT_PCICONF_ETH0] = QUBE1_ETH0_IRQ,
[COBALT_PCICONF_RAQSCSI] = SCSI_IRQ,
[COBALT_PCICONF_VIA] = 0,
[COBALT_PCICONF_PCISLOT] = PCISLOT_IRQ,
[COBALT_PCICONF_ETH1] = 0
};
static char irq_tab_cobalt[] = {
[COBALT_PCICONF_CPU] = 0,
[COBALT_PCICONF_ETH0] = ETH0_IRQ,
[COBALT_PCICONF_RAQSCSI] = SCSI_IRQ,
[COBALT_PCICONF_VIA] = 0,
[COBALT_PCICONF_PCISLOT] = PCISLOT_IRQ,
[COBALT_PCICONF_ETH1] = ETH1_IRQ
};
static char irq_tab_raq2[] = {
[COBALT_PCICONF_CPU] = 0,
[COBALT_PCICONF_ETH0] = ETH0_IRQ,
[COBALT_PCICONF_RAQSCSI] = RAQ2_SCSI_IRQ,
[COBALT_PCICONF_VIA] = 0,
[COBALT_PCICONF_PCISLOT] = PCISLOT_IRQ,
[COBALT_PCICONF_ETH1] = ETH1_IRQ
};
int pcibios_map_irq(
const struct pci_dev *dev, u8 slot, u8 pin)
{
if (cobalt_board_id <= COBALT_BRD_ID_QUBE1)
return irq_tab_qube1[slot];
if (cobalt_board_id == COBALT_BRD_ID_RAQ2)
return irq_tab_raq2[slot];
return irq_tab_cobalt[slot];
}
/* Do platform specific device initialization at pci_enable_device() time */
int pcibios_plat_dev_init(
struct pci_dev *dev)
{
return 0;
}
