{
UCHAR ucType; // one of ATOM_PP_THERMALCONTROLLER_*
UCHAR ucI2cLine; // as interpreted by DAL I2C
UCHAR ucI2cAddress;
UCHAR ucFanParameters; // Fan Control Parameters.
UCHAR ucFanMinRPM; // Fan Minimum RPM (hundreds) -- for display purposes only.
UCHAR ucFanMaxRPM; // Fan Maximum RPM (hundreds) -- for display purposes only.
UCHAR ucReserved; // ----
UCHAR ucFlags; // to be defined
} ATOM_PPLIB_THERMALCONTROLLER;
#define ATOM_PP_FANPARAMETERS_TACHOMETER_PULSES_PER_REVOLUTION_MASK 0x0f #define ATOM_PP_FANPARAMETERS_NOFAN 0x80 // No fan is connected to this controller.
#define ATOM_PP_THERMALCONTROLLER_NONE 0 #define ATOM_PP_THERMALCONTROLLER_LM63 1// Not used by PPLib #define ATOM_PP_THERMALCONTROLLER_ADM1032 2// Not used by PPLib #define ATOM_PP_THERMALCONTROLLER_ADM1030 3// Not used by PPLib #define ATOM_PP_THERMALCONTROLLER_MUA6649 4// Not used by PPLib #define ATOM_PP_THERMALCONTROLLER_LM64 5 #define ATOM_PP_THERMALCONTROLLER_F75375 6// Not used by PPLib #define ATOM_PP_THERMALCONTROLLER_RV6xx 7 #define ATOM_PP_THERMALCONTROLLER_RV770 8 #define ATOM_PP_THERMALCONTROLLER_ADT7473 9 #define ATOM_PP_THERMALCONTROLLER_KONG 10 #define ATOM_PP_THERMALCONTROLLER_EXTERNAL_GPIO 11 #define ATOM_PP_THERMALCONTROLLER_EVERGREEN 12 #define ATOM_PP_THERMALCONTROLLER_EMC2103 13/* 0x0D */ // Only fan control will be implemented, do NOT show this in PPGen. #define ATOM_PP_THERMALCONTROLLER_SUMO 14/* 0x0E */ // Sumo type, used internally #define ATOM_PP_THERMALCONTROLLER_NISLANDS 15 #define ATOM_PP_THERMALCONTROLLER_SISLANDS 16 #define ATOM_PP_THERMALCONTROLLER_LM96163 17 #define ATOM_PP_THERMALCONTROLLER_CISLANDS 18 #define ATOM_PP_THERMALCONTROLLER_KAVERI 19 #define ATOM_PP_THERMALCONTROLLER_ICELAND 20 #define ATOM_PP_THERMALCONTROLLER_TONGA 21 #define ATOM_PP_THERMALCONTROLLER_FIJI 22 #define ATOM_PP_THERMALCONTROLLER_POLARIS10 23 #define ATOM_PP_THERMALCONTROLLER_VEGA10 24
// Thermal controller 'combo type' to use an external controller for Fan control and an internal controller for thermal. // We probably should reserve the bit 0x80 for this use. // To keep the number of these types low we should also use the same code for all ASICs (i.e. do not distinguish RV6xx and RV7xx Internal here). // The driver can pick the correct internal controller based on the ASIC. #define ATOM_PP_THERMALCONTROLLER_ADT7473_WITH_INTERNAL 0x89 // ADT7473 Fan Control + Internal Thermal Controller #define ATOM_PP_THERMALCONTROLLER_EMC2103_WITH_INTERNAL 0x8D // EMC2103 Fan Control + Internal Thermal Controller
typedefstruct _ATOM_PPLIB_FANTABLE
{
UCHAR ucFanTableFormat; // Change this if the table format changes or version changes so that the other fields are not the same.
UCHAR ucTHyst; // Temperature hysteresis. Integer.
USHORT usTMin; // The temperature, in 0.01 centigrades, below which we just run at a minimal PWM.
USHORT usTMed; // The middle temperature where we change slopes.
USHORT usTHigh; // The high point above TMed for adjusting the second slope.
USHORT usPWMMin; // The minimum PWM value in percent (0.01% increments).
USHORT usPWMMed; // The PWM value (in percent) at TMed.
USHORT usPWMHigh; // The PWM value at THigh.
} ATOM_PPLIB_FANTABLE;
typedefstruct _ATOM_PPLIB_FANTABLE2
{
ATOM_PPLIB_FANTABLE basicTable;
USHORT usTMax; // The max temperature
} ATOM_PPLIB_FANTABLE2;
typedefstruct _ATOM_PPLIB_EXTENDEDHEADER
{
USHORT usSize;
ULONG ulMaxEngineClock; // For Overdrive.
ULONG ulMaxMemoryClock; // For Overdrive. // Add extra system parameters here, always adjust size to include all fields.
USHORT usVCETableOffset; //points to ATOM_PPLIB_VCE_Table
USHORT usUVDTableOffset; //points to ATOM_PPLIB_UVD_Table
USHORT usSAMUTableOffset; //points to ATOM_PPLIB_SAMU_Table
USHORT usPPMTableOffset; //points to ATOM_PPLIB_PPM_Table
USHORT usACPTableOffset; //points to ATOM_PPLIB_ACP_Table /* points to ATOM_PPLIB_POWERTUNE_Table */
USHORT usPowerTuneTableOffset; /* points to ATOM_PPLIB_CLOCK_Voltage_Dependency_Table for sclkVddgfxTable */
USHORT usSclkVddgfxTableOffset;
USHORT usVQBudgetingTableOffset; /* points to the vqBudgetingTable; */
} ATOM_PPLIB_EXTENDEDHEADER;
//// ATOM_PPLIB_POWERPLAYTABLE::ulPlatformCaps #define ATOM_PP_PLATFORM_CAP_BACKBIAS 1 #define ATOM_PP_PLATFORM_CAP_POWERPLAY 2 #define ATOM_PP_PLATFORM_CAP_SBIOSPOWERSOURCE 4 #define ATOM_PP_PLATFORM_CAP_ASPM_L0s 8 #define ATOM_PP_PLATFORM_CAP_ASPM_L1 16 #define ATOM_PP_PLATFORM_CAP_HARDWAREDC 32 #define ATOM_PP_PLATFORM_CAP_GEMINIPRIMARY 64 #define ATOM_PP_PLATFORM_CAP_STEPVDDC 128 #define ATOM_PP_PLATFORM_CAP_VOLTAGECONTROL 256 #define ATOM_PP_PLATFORM_CAP_SIDEPORTCONTROL 512 #define ATOM_PP_PLATFORM_CAP_TURNOFFPLL_ASPML1 1024 #define ATOM_PP_PLATFORM_CAP_HTLINKCONTROL 2048 #define ATOM_PP_PLATFORM_CAP_MVDDCONTROL 4096 #define ATOM_PP_PLATFORM_CAP_GOTO_BOOT_ON_ALERT 0x2000 // Go to boot state on alerts, e.g. on an AC->DC transition. #define ATOM_PP_PLATFORM_CAP_DONT_WAIT_FOR_VBLANK_ON_ALERT 0x4000 // Do NOT wait for VBLANK during an alert (e.g. AC->DC transition). #define ATOM_PP_PLATFORM_CAP_VDDCI_CONTROL 0x8000 // Does the driver control VDDCI independently from VDDC. #define ATOM_PP_PLATFORM_CAP_REGULATOR_HOT 0x00010000 // Enable the 'regulator hot' feature. #define ATOM_PP_PLATFORM_CAP_BACO 0x00020000 // Does the driver supports BACO state. #define ATOM_PP_PLATFORM_CAP_NEW_CAC_VOLTAGE 0x00040000 // Does the driver supports new CAC voltage table. #define ATOM_PP_PLATFORM_CAP_REVERT_GPIO5_POLARITY 0x00080000 // Does the driver supports revert GPIO5 polarity. #define ATOM_PP_PLATFORM_CAP_OUTPUT_THERMAL2GPIO17 0x00100000 // Does the driver supports thermal2GPIO17. #define ATOM_PP_PLATFORM_CAP_VRHOT_GPIO_CONFIGURABLE 0x00200000 // Does the driver supports VR HOT GPIO Configurable. #define ATOM_PP_PLATFORM_CAP_TEMP_INVERSION 0x00400000 // Does the driver supports Temp Inversion feature. #define ATOM_PP_PLATFORM_CAP_EVV 0x00800000 #define ATOM_PP_PLATFORM_COMBINE_PCC_WITH_THERMAL_SIGNAL 0x01000000 #define ATOM_PP_PLATFORM_LOAD_POST_PRODUCTION_FIRMWARE 0x02000000 #define ATOM_PP_PLATFORM_CAP_DISABLE_USING_ACTUAL_TEMPERATURE_FOR_POWER_CALC 0x04000000 #define ATOM_PP_PLATFORM_CAP_VRHOT_POLARITY_HIGH 0x08000000
// offset from start of this table to array of ucNumStates ATOM_PPLIB_STATE structures
USHORT usStateArrayOffset;
// offset from start of this table to array of ASIC-specific structures, // currently ATOM_PPLIB_CLOCK_INFO.
USHORT usClockInfoArrayOffset;
// offset from start of this table to array of ATOM_PPLIB_NONCLOCK_INFO
USHORT usNonClockInfoArrayOffset;
USHORT usBackbiasTime; // in microseconds
USHORT usVoltageTime; // in microseconds
USHORT usTableSize; //the size of this structure, or the extended structure
typedefstruct _ATOM_PPLIB_POWERPLAYTABLE3
{
ATOM_PPLIB_POWERPLAYTABLE2 basicTable2;
USHORT usFormatID; // To be used ONLY by PPGen.
USHORT usFanTableOffset;
USHORT usExtendendedHeaderOffset;
} ATOM_PPLIB_POWERPLAYTABLE3, *LPATOM_PPLIB_POWERPLAYTABLE3;
typedefstruct _ATOM_PPLIB_POWERPLAYTABLE4
{
ATOM_PPLIB_POWERPLAYTABLE3 basicTable3;
ULONG ulGoldenPPID; // PPGen use only
ULONG ulGoldenRevision; // PPGen use only
USHORT usVddcDependencyOnSCLKOffset;
USHORT usVddciDependencyOnMCLKOffset;
USHORT usVddcDependencyOnMCLKOffset;
USHORT usMaxClockVoltageOnDCOffset;
USHORT usVddcPhaseShedLimitsTableOffset; // Points to ATOM_PPLIB_PhaseSheddingLimits_Table
USHORT usMvddDependencyOnMCLKOffset;
} ATOM_PPLIB_POWERPLAYTABLE4, *LPATOM_PPLIB_POWERPLAYTABLE4;
typedefstruct _ATOM_PPLIB_POWERPLAYTABLE5
{
ATOM_PPLIB_POWERPLAYTABLE4 basicTable4;
ULONG ulTDPLimit;
ULONG ulNearTDPLimit;
ULONG ulSQRampingThreshold;
USHORT usCACLeakageTableOffset; // Points to ATOM_PPLIB_CAC_Leakage_Table
ULONG ulCACLeakage; // The iLeakage for driver calculated CAC leakage table
USHORT usTDPODLimit;
USHORT usLoadLineSlope; // in milliOhms * 100
} ATOM_PPLIB_POWERPLAYTABLE5, *LPATOM_PPLIB_POWERPLAYTABLE5;
// Contained in an array starting at the offset // in ATOM_PPLIB_POWERPLAYTABLE::usNonClockInfoArrayOffset. // referenced from ATOM_PPLIB_STATE_INFO::ucNonClockStateIndex #define ATOM_PPLIB_NONCLOCKINFO_VER1 12 #define ATOM_PPLIB_NONCLOCKINFO_VER2 24 typedefstruct _ATOM_PPLIB_NONCLOCK_INFO
{
USHORT usClassification;
UCHAR ucMinTemperature;
UCHAR ucMaxTemperature;
ULONG ulCapsAndSettings;
UCHAR ucRequiredPower;
USHORT usClassification2;
ULONG ulVCLK;
ULONG ulDCLK;
UCHAR ucUnused[5];
} ATOM_PPLIB_NONCLOCK_INFO;
// Contained in an array starting at the offset // in ATOM_PPLIB_POWERPLAYTABLE::usClockInfoArrayOffset. // referenced from ATOM_PPLIB_STATE::ucClockStateIndices typedefstruct _ATOM_PPLIB_R600_CLOCK_INFO
{
USHORT usEngineClockLow;
UCHAR ucEngineClockHigh;
// ulFlags in ATOM_PPLIB_R600_CLOCK_INFO #define ATOM_PPLIB_R600_FLAGS_PCIEGEN2 1 #define ATOM_PPLIB_R600_FLAGS_UVDSAFE 2 #define ATOM_PPLIB_R600_FLAGS_BACKBIASENABLE 4 #define ATOM_PPLIB_R600_FLAGS_MEMORY_ODT_OFF 8 #define ATOM_PPLIB_R600_FLAGS_MEMORY_DLL_OFF 16 #define ATOM_PPLIB_R600_FLAGS_LOWPOWER 32// On the RV770 use 'low power' setting (sequencer S0).
typedefstruct _ATOM_PPLIB_RS780_CLOCK_INFO
{
USHORT usLowEngineClockLow; // Low Engine clock in MHz (the same way as on the R600).
UCHAR ucLowEngineClockHigh;
USHORT usHighEngineClockLow; // High Engine clock in MHz.
UCHAR ucHighEngineClockHigh;
USHORT usMemoryClockLow; // For now one of the ATOM_PPLIB_RS780_SPMCLK_XXXX constants.
UCHAR ucMemoryClockHigh; // Currentyl unused.
UCHAR ucPadding; // For proper alignment and size.
USHORT usVDDC; // For the 780, use: None, Low, High, Variable
UCHAR ucMaxHTLinkWidth; // From SBIOS - {2, 4, 8, 16}
UCHAR ucMinHTLinkWidth; // From SBIOS - {2, 4, 8, 16}. Effective only if CDLW enabled. Minimum down stream width could
USHORT usHTLinkFreq; // See definition ATOM_PPLIB_RS780_HTLINKFREQ_xxx or in MHz(>=200).
ULONG ulFlags;
} ATOM_PPLIB_RS780_CLOCK_INFO;
#define ATOM_PPLIB_RS780_SPMCLK_NONE 0// We cannot change the side port memory clock, leave it as it is. #define ATOM_PPLIB_RS780_SPMCLK_LOW 1 #define ATOM_PPLIB_RS780_SPMCLK_HIGH 2
typedefstruct _ATOM_PPLIB_STATE_V2
{ //number of valid dpm levels in this state; Driver uses it to calculate the whole //size of the state: sizeof(ATOM_PPLIB_STATE_V2) + (ucNumDPMLevels - 1) * sizeof(UCHAR)
UCHAR ucNumDPMLevels;
//a index to the array of nonClockInfos
UCHAR nonClockInfoIndex; /** *DriverwillreadthefirstucNumDPMLevelsinthisarray
*/
UCHAR clockInfoIndex[];
} ATOM_PPLIB_STATE_V2;
typedefstruct _StateArray{ //how many states we have
UCHAR ucNumEntries;
typedefstruct _NonClockInfoArray{ //how many non-clock levels we have. normally should be same as number of states
UCHAR ucNumEntries; //sizeof(ATOM_PPLIB_NONCLOCK_INFO)
UCHAR ucEntrySize;
typedefstruct _ATOM_PPLIB_Clock_Voltage_Limit_Table
{ // Number of entries.
UCHAR ucNumEntries; // Dynamically allocate entries.
ATOM_PPLIB_Clock_Voltage_Limit_Record entries[] __counted_by(ucNumEntries);
}ATOM_PPLIB_Clock_Voltage_Limit_Table;
union _ATOM_PPLIB_CAC_Leakage_Record
{ struct
{
USHORT usVddc; // We use this field for the "fake" standardized VDDC for power calculations; For CI and newer, we use this as the real VDDC value. in CI we read it as StdVoltageHiSidd
ULONG ulLeakageValue; // For CI and newer we use this as the "fake" standar VDDC value. in CI we read it as StdVoltageLoSidd
¤ Die Informationen auf dieser Webseite wurden
nach bestem Wissen sorgfältig zusammengestellt. Es wird jedoch weder Vollständigkeit, noch Richtigkeit,
noch Qualität der bereit gestellten Informationen zugesichert.0.14Bemerkung:
(vorverarbeitet am 2026-10-12)
¤
Die Informationen auf dieser Webseite wurden
nach bestem Wissen sorgfältig zusammengestellt. Es wird jedoch weder Vollständigkeit, noch Richtigkeit,
noch Qualität der bereit gestellten Informationen zugesichert.
Bemerkung:
Die farbliche Syntaxdarstellung und die Messung sind noch experimentell.