Quellcodebibliothek Statistik Leitseite products/Sources/formale Sprachen/C/Linux/arch/arm/boot/dts/ti/omap/   (Open Source Betriebssystem Version 6.17.9©)  Datei vom 24.10.2025 mit Größe 1 kB image not shown  

Quelle  omap3-igep0030-rev-g.dts   Sprache: unbekannt

 
// SPDX-License-Identifier: GPL-2.0-only
/*
 * Device Tree Source for IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
 *
 * Copyright (C) 2014 Javier Martinez Canillas <javier@dowhile0.org>
 * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com>
 */

#include "omap3-igep0030-common.dtsi"

/ {
 model = "IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)";
 compatible = "isee,omap3-igep0030-rev-g", "ti,omap3630", "ti,omap3";

 /* Regulator to trigger the WL_EN signal of the Wifi module */
 lbep5clwmc_wlen: regulator-lbep5clwmc-wlen {
  compatible = "regulator-fixed";
  regulator-name = "regulator-lbep5clwmc-wlen";
  regulator-min-microvolt = <3300000>;
  regulator-max-microvolt = <3300000>;
  gpio = <&gpio5 11 GPIO_ACTIVE_HIGH>;  /* gpio_139 - WL_EN */
  enable-active-high;
 };
};

&omap3_pmx_core {
 lbep5clwmc_pins: lbep5clwmc-pins {
  pinctrl-single,pins = <
   OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4) /* sdmmc2_dat4.gpio_136 - W_IRQ */
   OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat5.gpio_137 - BT_EN */
   OMAP3_CORE1_IOPAD(0x216a, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 - WL_EN */
  >;
 };

 leds_pins: leds-pins {
  pinctrl-single,pins = <
   OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4) /* i2c2_scl.gpio_168 */
  >;
 };

};

&i2c2 {
 status = "disabled";
};

&leds {
 pinctrl-names = "default";
 pinctrl-0 = <&leds_pins &leds_core2_pins>;

 boot {
  label = "omap3:green:boot";
  gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
  default-state = "on";
 };
};

&mmc2 {
 pinctrl-names = "default";
 pinctrl-0 = <&mmc2_pins &lbep5clwmc_pins>;
 vmmc-supply = <&lbep5clwmc_wlen>;
 bus-width = <4>;
 non-removable;

 #address-cells = <1>;
 #size-cells = <0>;
 wlcore: wlcore@2 {
  compatible = "ti,wl1835";
  reg = <2>;
  interrupt-parent = <&gpio5>;
  interrupts = <8 IRQ_TYPE_EDGE_RISING>; /* gpio 136 */
 };
};

&uart2 {
 bluetooth {
  compatible = "ti,wl1835-st";
  enable-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; /* gpio 137 */
  max-speed = <300000>;
 };
};

[ Dauer der Verarbeitung: 0.13 Sekunden  (vorverarbeitet)  ]