Quelle  x1e80100-hp-omnibook-x14.dts   Sprache: unbekannt

// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
 * Copyright (c) 2024, Xilin Wu <wuxilin123@gmail.com>
 */

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/gpio-keys.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>

#include "x1e80100.dtsi"
#include "x1e80100-pmics.dtsi"

/ {
 model = "HP Omnibook X 14";
 compatible = "hp,omnibook-x14", "qcom,x1e80100";
 chassis-type = "laptop";

 aliases {
  serial0 = &uart21;
  serial1 = &uart14;
 };

 wcd938x: audio-codec {
  compatible = "qcom,wcd9385-codec";

  pinctrl-names = "default";
  pinctrl-0 = <&wcd_default>;

  qcom,micbias1-microvolt = <1800000>;
  qcom,micbias2-microvolt = <1800000>;
  qcom,micbias3-microvolt = <1800000>;
  qcom,micbias4-microvolt = <1800000>;
  qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
  qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
  qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
  qcom,rx-device = <&wcd_rx>;
  qcom,tx-device = <&wcd_tx>;

  reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;

  vdd-buck-supply = <&vreg_l15b_1p8>;
  vdd-rxtx-supply = <&vreg_l15b_1p8>;
  vdd-io-supply = <&vreg_l15b_1p8>;
  vdd-mic-bias-supply = <&vreg_bob1>;

  #sound-dai-cells = <1>;
 };

 backlight: backlight {
  compatible = "pwm-backlight";
  pwms = <&pmk8550_pwm 0 5000000>;

  brightness-levels = <0 2048 4096 8192 16384 65535>;
  num-interpolated-steps = <20>;
  default-brightness-level = <80>;

  enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
  power-supply = <&vreg_edp_bl>;

  pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>;
  pinctrl-names = "default";
 };

 gpio-keys {
  compatible = "gpio-keys";

  pinctrl-0 = <&hall_int_n_default>;
  pinctrl-names = "default";

  switch-lid {
   gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
   linux,input-type = <EV_SW>;
   linux,code = <SW_LID>;
   wakeup-source;
   wakeup-event-action = <EV_ACT_DEASSERTED>;
  };
 };

 pmic-glink {
  compatible = "qcom,x1e80100-pmic-glink",
        "qcom,sm8550-pmic-glink",
        "qcom,pmic-glink";
  orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
        <&tlmm 123 GPIO_ACTIVE_HIGH>;
  #address-cells = <1>;
  #size-cells = <0>;

  /* Left-side port, closer to the screen */
  connector@0 {
   compatible = "usb-c-connector";
   reg = <0>;
   power-role = "dual";
   data-role = "dual";

   ports {
    #address-cells = <1>;
    #size-cells = <0>;

    port@0 {
     reg = <0>;

     pmic_glink_ss0_hs_in: endpoint {
      remote-endpoint = <&usb_1_ss0_dwc3_hs>;
     };
    };

    port@1 {
     reg = <1>;

     pmic_glink_ss0_ss_in: endpoint {
      remote-endpoint = <&retimer_ss0_ss_out>;
     };
    };

    port@2 {
     reg = <2>;

     pmic_glink_ss0_con_sbu_in: endpoint {
      remote-endpoint = <&retimer_ss0_con_sbu_out>;
     };
    };
   };
  };

  /* Left-side port, farther from the screen */
  connector@1 {
   compatible = "usb-c-connector";
   reg = <1>;
   power-role = "dual";
   data-role = "dual";

   ports {
    #address-cells = <1>;
    #size-cells = <0>;

    port@0 {
     reg = <0>;

     pmic_glink_ss1_hs_in: endpoint {
      remote-endpoint = <&usb_1_ss1_dwc3_hs>;
     };
    };

    port@1 {
     reg = <1>;

     pmic_glink_ss1_ss_in: endpoint {
      remote-endpoint = <&usb_1_ss1_qmpphy_out>;
     };
    };

    port@2 {
     reg = <2>;

     pmic_glink_ss1_sbu: endpoint {
      remote-endpoint = <&usb_1_ss1_sbu_mux>;
     };
    };
   };
  };
 };

 reserved-memory {
  linux,cma {
   compatible = "shared-dma-pool";
   size = <0x0 0x8000000>;
   reusable;
   linux,cma-default;
  };
 };

 sound: sound {
  compatible = "qcom,x1e80100-sndcard";
  model = "X1E80100-HP-OMNIBOOK-X14";
  audio-routing = "SpkrLeft IN", "WSA WSA_SPK1 OUT",
    "SpkrRight IN", "WSA WSA_SPK2 OUT",
    "IN1_HPHL", "HPHL_OUT",
    "IN2_HPHR", "HPHR_OUT",
    "AMIC2", "MIC BIAS2",
    "VA DMIC0", "MIC BIAS3",
    "VA DMIC1", "MIC BIAS3",
    "VA DMIC2", "MIC BIAS1",
    "VA DMIC3", "MIC BIAS1",
    "VA DMIC0", "VA MIC BIAS3",
    "VA DMIC1", "VA MIC BIAS3",
    "VA DMIC2", "VA MIC BIAS1",
    "VA DMIC3", "VA MIC BIAS1",
    "TX SWR_INPUT1", "ADC2_OUTPUT";

  wcd-playback-dai-link {
   link-name = "WCD Playback";

   cpu {
    sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
   };

   codec {
    sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
   };

   platform {
    sound-dai = <&q6apm>;
   };
  };

  wcd-capture-dai-link {
   link-name = "WCD Capture";

   cpu {
    sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
   };

   codec {
    sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
   };

   platform {
    sound-dai = <&q6apm>;
   };
  };

  wsa-dai-link {
   link-name = "WSA Playback";

   cpu {
    sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
   };

   codec {
    sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
   };

   platform {
    sound-dai = <&q6apm>;
   };
  };

  va-dai-link {
   link-name = "VA Capture";

   cpu {
    sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
   };

   codec {
    sound-dai = <&lpass_vamacro 0>;
   };

   platform {
    sound-dai = <&q6apm>;
   };
  };
 };

 vreg_edp_3p3: regulator-edp-3p3 {
  compatible = "regulator-fixed";

  regulator-name = "VREG_EDP_3P3";
  regulator-min-microvolt = <3300000>;
  regulator-max-microvolt = <3300000>;

  gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
  enable-active-high;

  pinctrl-0 = <&edp_reg_en>;
  pinctrl-names = "default";

  regulator-boot-on;
 };

 vreg_edp_bl: regulator-edp-bl {
  compatible = "regulator-fixed";

  regulator-name = "VBL9";
  regulator-min-microvolt = <3600000>;
  regulator-max-microvolt = <3600000>;

  gpio = <&pmc8380_3_gpios 10 GPIO_ACTIVE_HIGH>;
  enable-active-high;

  pinctrl-names = "default";
  pinctrl-0 = <&edp_bl_reg_en>;

  regulator-boot-on;
 };

 vreg_misc_3p3: regulator-misc-3p3 {
  compatible = "regulator-fixed";

  regulator-name = "VREG_MISC_3P3";
  regulator-min-microvolt = <3300000>;
  regulator-max-microvolt = <3300000>;

  gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
  enable-active-high;

  pinctrl-names = "default";
  pinctrl-0 = <&misc_3p3_reg_en>;

  regulator-boot-on;
  regulator-always-on;
 };

 vreg_nvme: regulator-nvme {
  compatible = "regulator-fixed";

  regulator-name = "VREG_NVME_3P3";
  regulator-min-microvolt = <3300000>;
  regulator-max-microvolt = <3300000>;

  gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
  enable-active-high;

  pinctrl-0 = <&nvme_reg_en>;
  pinctrl-names = "default";

  regulator-boot-on;
 };

 vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
  compatible = "regulator-fixed";

  regulator-name = "VREG_RTMR0_1P15";
  regulator-min-microvolt = <1150000>;
  regulator-max-microvolt = <1150000>;

  gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
  enable-active-high;

  pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
  pinctrl-names = "default";

  regulator-boot-on;
 };

 vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
  compatible = "regulator-fixed";

  regulator-name = "VREG_RTMR0_1P8";
  regulator-min-microvolt = <1800000>;
  regulator-max-microvolt = <1800000>;

  gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
  enable-active-high;

  pinctrl-0 = <&usb0_1p8_reg_en>;
  pinctrl-names = "default";

  regulator-boot-on;
 };

 vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
  compatible = "regulator-fixed";

  regulator-name = "VREG_RTMR0_3P3";
  regulator-min-microvolt = <3300000>;
  regulator-max-microvolt = <3300000>;

  gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
  enable-active-high;

  pinctrl-0 = <&usb0_3p3_reg_en>;
  pinctrl-names = "default";

  regulator-boot-on;
 };

 vreg_vph_pwr: regulator-vph-pwr {
  compatible = "regulator-fixed";

  regulator-name = "vreg_vph_pwr";
  regulator-min-microvolt = <3700000>;
  regulator-max-microvolt = <3700000>;

  regulator-always-on;
  regulator-boot-on;
 };

 vreg_wcn_3p3: regulator-wcn-3p3 {
  compatible = "regulator-fixed";

  regulator-name = "VREG_WCN_3P3";
  regulator-min-microvolt = <3300000>;
  regulator-max-microvolt = <3300000>;

  gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
  enable-active-high;

  pinctrl-0 = <&wcn_sw_en>;
  pinctrl-names = "default";

  regulator-boot-on;
 };

 /*
  * TODO: These two regulators are actually part of the removable M.2
  * card and not the CRD mainboard. Need to describe this differently.
  * Functionally it works correctly, because all we need to do is to
  * turn on the actual 3.3V supply above.
  */
 vreg_wcn_0p95: regulator-wcn-0p95 {
  compatible = "regulator-fixed";

  regulator-name = "VREG_WCN_0P95";
  regulator-min-microvolt = <950000>;
  regulator-max-microvolt = <950000>;

  vin-supply = <&vreg_wcn_3p3>;
 };

 vreg_wcn_1p9: regulator-wcn-1p9 {
  compatible = "regulator-fixed";

  regulator-name = "VREG_WCN_1P9";
  regulator-min-microvolt = <1900000>;
  regulator-max-microvolt = <1900000>;

  vin-supply = <&vreg_wcn_3p3>;
 };

 wcn6855-pmu {
  compatible = "qcom,wcn6855-pmu";

  vddaon-supply = <&vreg_wcn_0p95>;
  vddio-supply = <&vreg_wcn_1p9>;
  vddpcie1p3-supply = <&vreg_wcn_1p9>;
  vddpcie1p9-supply = <&vreg_wcn_1p9>;
  vddpmu-supply = <&vreg_wcn_0p95>;
  vddpmumx-supply = <&vreg_wcn_0p95>;
  vddpmucx-supply = <&vreg_wcn_0p95>;
  vddrfa0p95-supply = <&vreg_wcn_0p95>;
  vddrfa1p3-supply = <&vreg_wcn_1p9>;
  vddrfa1p9-supply = <&vreg_wcn_1p9>;

  wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
  bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;

  pinctrl-0 = <&wcn_wlan_bt_en>;
  pinctrl-names = "default";

  regulators {
   vreg_pmu_rfa_cmn_0p8: ldo0 {
    regulator-name = "vreg_pmu_rfa_cmn_0p8";
   };

   vreg_pmu_aon_0p8: ldo1 {
    regulator-name = "vreg_pmu_aon_0p8";
   };

   vreg_pmu_wlcx_0p8: ldo2 {
    regulator-name = "vreg_pmu_wlcx_0p8";
   };

   vreg_pmu_wlmx_0p8: ldo3 {
    regulator-name = "vreg_pmu_wlmx_0p8";
   };

   vreg_pmu_btcmx_0p8: ldo4 {
    regulator-name = "vreg_pmu_btcmx_0p8";
   };

   vreg_pmu_pcie_1p8: ldo5 {
    regulator-name = "vreg_pmu_pcie_1p8";
   };

   vreg_pmu_pcie_0p9: ldo6 {
    regulator-name = "vreg_pmu_pcie_0p9";
   };

   vreg_pmu_rfa_0p8: ldo7 {
    regulator-name = "vreg_pmu_rfa_0p8";
   };

   vreg_pmu_rfa_1p2: ldo8 {
    regulator-name = "vreg_pmu_rfa_1p2";
   };

   vreg_pmu_rfa_1p7: ldo9 {
    regulator-name = "vreg_pmu_rfa_1p7";
   };
  };
 };

 usb-1-ss1-sbu-mux {
  compatible = "onnn,fsusb42", "gpio-sbu-mux";

  enable-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>;
  select-gpios = <&tlmm 178 GPIO_ACTIVE_HIGH>;

  pinctrl-0 = <&usb_1_ss1_sbu_default>;
  pinctrl-names = "default";

  mode-switch;
  orientation-switch;

  port {
   usb_1_ss1_sbu_mux: endpoint {
    remote-endpoint = <&pmic_glink_ss1_sbu>;
   };
  };
 };
};

&apps_rsc {
 regulators-0 {
  compatible = "qcom,pm8550-rpmh-regulators";
  qcom,pmic-id = "b";

  vdd-bob1-supply = <&vreg_vph_pwr>;
  vdd-bob2-supply = <&vreg_vph_pwr>;
  vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
  vdd-l2-l13-l14-supply = <&vreg_bob1>;
  vdd-l5-l16-supply = <&vreg_bob1>;
  vdd-l6-l7-supply = <&vreg_bob2>;
  vdd-l8-l9-supply = <&vreg_bob1>;
  vdd-l12-supply = <&vreg_s5j_1p2>;
  vdd-l15-supply = <&vreg_s4c_1p8>;
  vdd-l17-supply = <&vreg_bob2>;

  vreg_bob1: bob1 {
   regulator-name = "vreg_bob1";
   regulator-min-microvolt = <3008000>;
   regulator-max-microvolt = <3960000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_bob2: bob2 {
   regulator-name = "vreg_bob2";
   regulator-min-microvolt = <2504000>;
   regulator-max-microvolt = <3008000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l1b_1p8: ldo1 {
   regulator-name = "vreg_l1b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2b_3p0: ldo2 {
   regulator-name = "vreg_l2b_3p0";
   regulator-min-microvolt = <3072000>;
   regulator-max-microvolt = <3100000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l4b_1p8: ldo4 {
   regulator-name = "vreg_l4b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l5b_3p0: ldo5 {
   regulator-name = "vreg_l5b_3p0";
   regulator-min-microvolt = <3000000>;
   regulator-max-microvolt = <3000000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l6b_1p8: ldo6 {
   regulator-name = "vreg_l6b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <2960000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l7b_2p8: ldo7 {
   regulator-name = "vreg_l7b_2p8";
   regulator-min-microvolt = <2800000>;
   regulator-max-microvolt = <2800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l8b_3p0: ldo8 {
   regulator-name = "vreg_l8b_3p0";
   regulator-min-microvolt = <3072000>;
   regulator-max-microvolt = <3072000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l9b_2p9: ldo9 {
   regulator-name = "vreg_l9b_2p9";
   regulator-min-microvolt = <2960000>;
   regulator-max-microvolt = <2960000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l10b_1p8: ldo10 {
   regulator-name = "vreg_l10b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l12b_1p2: ldo12 {
   regulator-name = "vreg_l12b_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-always-on;
  };

  vreg_l13b_3p0: ldo13 {
   regulator-name = "vreg_l13b_3p0";
   regulator-min-microvolt = <3072000>;
   regulator-max-microvolt = <3100000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l14b_3p0: ldo14 {
   regulator-name = "vreg_l14b_3p0";
   regulator-min-microvolt = <3072000>;
   regulator-max-microvolt = <3072000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l15b_1p8: ldo15 {
   regulator-name = "vreg_l15b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-always-on;
  };

  vreg_l16b_2p9: ldo16 {
   regulator-name = "vreg_l16b_2p9";
   regulator-min-microvolt = <2912000>;
   regulator-max-microvolt = <2912000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l17b_2p5: ldo17 {
   regulator-name = "vreg_l17b_2p5";
   regulator-min-microvolt = <2504000>;
   regulator-max-microvolt = <2504000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-1 {
  compatible = "qcom,pm8550ve-rpmh-regulators";
  qcom,pmic-id = "c";

  vdd-l1-supply = <&vreg_s5j_1p2>;
  vdd-l2-supply = <&vreg_s1f_0p7>;
  vdd-l3-supply = <&vreg_s1f_0p7>;
  vdd-s4-supply = <&vreg_vph_pwr>;

  vreg_s4c_1p8: smps4 {
   regulator-name = "vreg_s4c_1p8";
   regulator-min-microvolt = <1856000>;
   regulator-max-microvolt = <2000000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l1c_1p2: ldo1 {
   regulator-name = "vreg_l1c_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2c_0p8: ldo2 {
   regulator-name = "vreg_l2c_0p8";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3c_0p8: ldo3 {
   regulator-name = "vreg_l3c_0p8";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-2 {
  compatible = "qcom,pmc8380-rpmh-regulators";
  qcom,pmic-id = "d";

  vdd-l1-supply = <&vreg_s1f_0p7>;
  vdd-l2-supply = <&vreg_s1f_0p7>;
  vdd-l3-supply = <&vreg_s4c_1p8>;
  vdd-s1-supply = <&vreg_vph_pwr>;

  vreg_l1d_0p8: ldo1 {
   regulator-name = "vreg_l1d_0p8";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2d_0p9: ldo2 {
   regulator-name = "vreg_l2d_0p9";
   regulator-min-microvolt = <912000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3d_1p8: ldo3 {
   regulator-name = "vreg_l3d_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-3 {
  compatible = "qcom,pmc8380-rpmh-regulators";
  qcom,pmic-id = "e";

  vdd-l2-supply = <&vreg_s1f_0p7>;
  vdd-l3-supply = <&vreg_s5j_1p2>;

  vreg_l2e_0p8: ldo2 {
   regulator-name = "vreg_l2e_0p8";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3e_1p2: ldo3 {
   regulator-name = "vreg_l3e_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-4 {
  compatible = "qcom,pmc8380-rpmh-regulators";
  qcom,pmic-id = "f";

  vdd-l1-supply = <&vreg_s5j_1p2>;
  vdd-l2-supply = <&vreg_s5j_1p2>;
  vdd-l3-supply = <&vreg_s5j_1p2>;
  vdd-s1-supply = <&vreg_vph_pwr>;

  vreg_s1f_0p7: smps1 {
   regulator-name = "vreg_s1f_0p7";
   regulator-min-microvolt = <700000>;
   regulator-max-microvolt = <1100000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l1f_1p0: ldo1 {
   regulator-name = "vreg_l1f_1p0";
   regulator-min-microvolt = <1024000>;
   regulator-max-microvolt = <1024000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2f_1p0: ldo2 {
   regulator-name = "vreg_l2f_1p0";
   regulator-min-microvolt = <1024000>;
   regulator-max-microvolt = <1024000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3f_1p0: ldo3 {
   regulator-name = "vreg_l3f_1p0";
   regulator-min-microvolt = <1024000>;
   regulator-max-microvolt = <1024000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-6 {
  compatible = "qcom,pm8550ve-rpmh-regulators";
  qcom,pmic-id = "i";

  vdd-l1-supply = <&vreg_s4c_1p8>;
  vdd-l2-supply = <&vreg_s5j_1p2>;
  vdd-l3-supply = <&vreg_s1f_0p7>;
  vdd-s1-supply = <&vreg_vph_pwr>;
  vdd-s2-supply = <&vreg_vph_pwr>;

  vreg_s1i_0p9: smps1 {
   regulator-name = "vreg_s1i_0p9";
   regulator-min-microvolt = <900000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s2i_1p0: smps2 {
   regulator-name = "vreg_s2i_1p0";
   regulator-min-microvolt = <1000000>;
   regulator-max-microvolt = <1100000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l1i_1p8: ldo1 {
   regulator-name = "vreg_l1i_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2i_1p2: ldo2 {
   regulator-name = "vreg_l2i_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3i_0p8: ldo3 {
   regulator-name = "vreg_l3i_0p8";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-7 {
  compatible = "qcom,pm8550ve-rpmh-regulators";
  qcom,pmic-id = "j";

  vdd-l1-supply = <&vreg_s1f_0p7>;
  vdd-l2-supply = <&vreg_s5j_1p2>;
  vdd-l3-supply = <&vreg_s1f_0p7>;
  vdd-s5-supply = <&vreg_vph_pwr>;

  vreg_s5j_1p2: smps5 {
   regulator-name = "vreg_s5j_1p2";
   regulator-min-microvolt = <1256000>;
   regulator-max-microvolt = <1304000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l1j_0p8: ldo1 {
   regulator-name = "vreg_l1j_0p8";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2j_1p2: ldo2 {
   regulator-name = "vreg_l2j_1p2";
   regulator-min-microvolt = <1256000>;
   regulator-max-microvolt = <1256000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3j_0p8: ldo3 {
   regulator-name = "vreg_l3j_0p8";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };
 };
};

&gpu {
 status = "okay";

 zap-shader {
  firmware-name = "qcom/x1e80100/hp/omnibook-x14/qcdxkmsuc8380.mbn";
 };
};

&i2c0 {
 clock-frequency = <400000>;

 status = "okay";

 keyboard@3a {
  compatible = "hid-over-i2c";
  reg = <0x3a>;

  hid-descr-addr = <0x1>;
  interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;

  vdd-supply = <&vreg_misc_3p3>;
  vddl-supply = <&vreg_l12b_1p2>;

  pinctrl-0 = <&kybd_default>;
  pinctrl-names = "default";

  wakeup-source;
 };

 touchpad@15 {
  compatible = "hid-over-i2c";
  reg = <0x15>;

  hid-descr-addr = <0x1>;
  interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;

  vdd-supply = <&vreg_misc_3p3>;
  vddl-supply = <&vreg_l12b_1p2>;

  pinctrl-0 = <&tpad_default>;
  pinctrl-names = "default";

  wakeup-source;
 };
};

&i2c3 {
 clock-frequency = <400000>;

 status = "okay";

 typec-mux@8 {
  compatible = "parade,ps8830";
  reg = <0x08>;

  clocks = <&rpmhcc RPMH_RF_CLK3>;

  vdd-supply = <&vreg_rtmr0_1p15>;
  vdd33-supply = <&vreg_rtmr0_3p3>;
  vdd33-cap-supply = <&vreg_rtmr0_3p3>;
  vddar-supply = <&vreg_rtmr0_1p15>;
  vddat-supply = <&vreg_rtmr0_1p15>;
  vddio-supply = <&vreg_rtmr0_1p8>;

  reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;

  pinctrl-0 = <&rtmr0_default>;
  pinctrl-names = "default";

  orientation-switch;
  retimer-switch;

  ports {
   #address-cells = <1>;
   #size-cells = <0>;

   port@0 {
    reg = <0>;

    retimer_ss0_ss_out: endpoint {
     remote-endpoint = <&pmic_glink_ss0_ss_in>;
    };
   };

   port@1 {
    reg = <1>;

    retimer_ss0_ss_in: endpoint {
     remote-endpoint = <&usb_1_ss0_qmpphy_out>;
    };
   };

   port@2 {
    reg = <2>;

    retimer_ss0_con_sbu_out: endpoint {
     remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
    };
   };
  };
 };
};

&i2c5 {
 clock-frequency = <400000>;
 status = "okay";

 eusb3_repeater: redriver@47 {
  compatible = "nxp,ptn3222";
  reg = <0x47>;
  #phy-cells = <0>;

  vdd3v3-supply = <&vreg_l13b_3p0>;
  vdd1v8-supply = <&vreg_l4b_1p8>;

  reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;

  pinctrl-0 = <&eusb3_reset_n>;
  pinctrl-names = "default";

 };
};

&i2c8 {
 clock-frequency = <400000>;

 status = "okay";

 touchscreen@10 {
  compatible = "hid-over-i2c";
  reg = <0x10>;

  hid-descr-addr = <0x1>;
  interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;

  vdd-supply = <&vreg_misc_3p3>;
  vddl-supply = <&vreg_l15b_1p8>;

  pinctrl-0 = <&ts0_default>;
  pinctrl-names = "default";
 };
};

&lpass_tlmm {
 spkr_01_sd_n_active: spkr-01-sd-n-active-state {
  pins = "gpio12";
  function = "gpio";
  drive-strength = <16>;
  bias-disable;
  output-low;
 };
};

&lpass_vamacro {
 pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
 pinctrl-names = "default";

 vdd-micb-supply = <&vreg_l1b_1p8>;
 qcom,dmic-sample-rate = <4800000>;
};

&mdss {
 status = "okay";
};

&mdss_dp0 {
 status = "okay";
};

&mdss_dp0_out {
 data-lanes = <0 1>;
 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
};

&mdss_dp1 {
 status = "okay";
};

&mdss_dp1_out {
 data-lanes = <0 1>;
 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
};

&mdss_dp3 {
 /delete-property/ #sound-dai-cells;

 status = "okay";

 aux-bus {
  panel {
   compatible = "edp-panel";
   power-supply = <&vreg_edp_3p3>;

   backlight = <&backlight>;

   port {
    edp_panel_in: endpoint {
     remote-endpoint = <&mdss_dp3_out>;
    };
   };
  };
 };

 ports {
  port@1 {
   reg = <1>;

   mdss_dp3_out: endpoint {
    data-lanes = <0 1 2 3>;
    link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;

    remote-endpoint = <&edp_panel_in>;
   };
  };
 };
};

&mdss_dp3_phy {
 vdda-phy-supply = <&vreg_l3j_0p8>;
 vdda-pll-supply = <&vreg_l2j_1p2>;

 status = "okay";
};

&pcie4 {
 perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
 wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;

 pinctrl-0 = <&pcie4_default>;
 pinctrl-names = "default";

 status = "okay";
};

&pcie4_phy {
 vdda-phy-supply = <&vreg_l3i_0p8>;
 vdda-pll-supply = <&vreg_l3e_1p2>;

 status = "okay";
};

&pcie4_port0 {
 wifi@0 {
  compatible = "pci17cb,1107";
  reg = <0x10000 0x0 0x0 0x0 0x0>;

  vddaon-supply = <&vreg_pmu_aon_0p8>;
  vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
  vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
  vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
  vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
  vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
  vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
  vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
  vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
 };
};

&pcie6a {
 perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
 wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;

 vddpe-3v3-supply = <&vreg_nvme>;

 pinctrl-0 = <&pcie6a_default>;
 pinctrl-names = "default";

 status = "okay";
};

&pcie6a_phy {
 vdda-phy-supply = <&vreg_l1d_0p8>;
 vdda-pll-supply = <&vreg_l2j_1p2>;

 status = "okay";
};

&pm8550_gpios {
 rtmr0_default: rtmr0-reset-n-active-state {
  pins = "gpio10";
  function = "normal";
  power-source = <1>; /* 1.8V */
  bias-disable;
  input-disable;
  output-enable;
 };

 usb0_3p3_reg_en: usb0-3p3-reg-en-state {
  pins = "gpio11";
  function = "normal";
  power-source = <1>; /* 1.8V */
  bias-disable;
  input-disable;
  output-enable;
 };
};

&pm8550ve_8_gpios {
 misc_3p3_reg_en: misc-3p3-reg-en-state {
  pins = "gpio6";
  function = "normal";
  bias-disable;
  drive-push-pull;
  input-disable;
  output-enable;
  power-source = <1>; /* 1.8 V */
  qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
 };
};

&pm8550ve_9_gpios {
 usb0_1p8_reg_en: usb0-1p8-reg-en-state {
  pins = "gpio8";
  function = "normal";
  power-source = <1>; /* 1.8V */
  bias-disable;
  input-disable;
  output-enable;
 };
};

&pmc8380_3_gpios {
 edp_bl_en: edp-bl-en-state {
  pins = "gpio4";
  function = "normal";
  power-source = <1>; /* 1.8V */
  input-disable;
  output-enable;
 };

 edp_bl_reg_en: edp-bl-reg-en-state {
  pins = "gpio10";
  function = "normal";
 };

};

&pmc8380_5_gpios {
 usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
  pins = "gpio8";
  function = "normal";
  power-source = <1>; /* 1.8V */
  bias-disable;
  input-disable;
  output-enable;
 };
};

&pmk8550_gpios {
 edp_bl_pwm: edp-bl-pwm-state {
  pins = "gpio5";
  function = "func3";
 };
};

&pmk8550_pwm {
 status = "okay";
};

&qupv3_0 {
 status = "okay";
};

&qupv3_1 {
 status = "okay";
};

&qupv3_2 {
 status = "okay";
};

&remoteproc_adsp {
 firmware-name = "qcom/x1e80100/hp/omnibook-x14/qcadsp8380.mbn",
   "qcom/x1e80100/hp/omnibook-x14/adsp_dtbs.elf";

 status = "okay";
};

&remoteproc_cdsp {
 firmware-name = "qcom/x1e80100/hp/omnibook-x14/qccdsp8380.mbn",
   "qcom/x1e80100/hp/omnibook-x14/cdsp_dtbs.elf";

 status = "okay";
};

&smb2360_0 {
 status = "okay";
};

&smb2360_0_eusb2_repeater {
 vdd18-supply = <&vreg_l3d_1p8>;
 vdd3-supply = <&vreg_l2b_3p0>;
};

&smb2360_1 {
 status = "okay";
};

&smb2360_1_eusb2_repeater {
 vdd18-supply = <&vreg_l3d_1p8>;
 vdd3-supply = <&vreg_l14b_3p0>;
};

&swr0 {
 pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
 pinctrl-names = "default";

 status = "okay";

 /* WSA8845, Left Speaker */
 left_spkr: speaker@0,0 {
  compatible = "sdw20217020400";
  reg = <0 0>;
  reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
  #sound-dai-cells = <0>;
  sound-name-prefix = "SpkrLeft";
  vdd-1p8-supply = <&vreg_l15b_1p8>;
  vdd-io-supply = <&vreg_l12b_1p2>;
  qcom,port-mapping = <1 2 3 7 10 13>;
 };

 /* WSA8845, Right Speaker */
 right_spkr: speaker@0,1 {
  compatible = "sdw20217020400";
  reg = <0 1>;
  reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
  #sound-dai-cells = <0>;
  sound-name-prefix = "SpkrRight";
  vdd-1p8-supply = <&vreg_l15b_1p8>;
  vdd-io-supply = <&vreg_l12b_1p2>;
  qcom,port-mapping = <4 5 6 7 11 13>;
 };
};

&swr1 {
 status = "okay";

 /* WCD9385 RX */
 wcd_rx: codec@0,4 {
  compatible = "sdw20217010d00";
  reg = <0 4>;
  qcom,rx-port-mapping = <1 2 3 4 5>;
 };
};

&swr2 {
 status = "okay";

 /* WCD9385 TX */
 wcd_tx: codec@0,3 {
  compatible = "sdw20217010d00";
  reg = <0 3>;
  qcom,tx-port-mapping = <2 2 3 4>;
 };
};

&tlmm {
 gpio-reserved-ranges = <34 2>, /* Unused */
          <44 4>, /* SPI (TPM) */
          <72 2>, /* Secure EC I2C connection (?) */
          <238 1>; /* UFS Reset */

 edp_reg_en: edp-reg-en-state {
  pins = "gpio70";
  function = "gpio";
  drive-strength = <16>;
  bias-disable;
 };

 eusb3_reset_n: eusb3-reset-n-state {
  pins = "gpio6";
  function = "gpio";
  drive-strength = <2>;
  bias-disable;
  output-low;
 };

 hall_int_n_default: hall-int-n-state {
  pins = "gpio92";
  function = "gpio";
  bias-disable;
 };

 kybd_default: kybd-default-state {
  pins = "gpio67";
  function = "gpio";
  bias-pull-up;
 };

 nvme_reg_en: nvme-reg-en-state {
  pins = "gpio18";
  function = "gpio";
  drive-strength = <2>;
  bias-disable;
 };

 pcie4_default: pcie4-default-state {
  clkreq-n-pins {
   pins = "gpio147";
   function = "pcie4_clk";
   drive-strength = <2>;
   bias-pull-up;
  };

  perst-n-pins {
   pins = "gpio146";
   function = "gpio";
   drive-strength = <2>;
   bias-disable;
  };

  wake-n-pins {
   pins = "gpio148";
   function = "gpio";
   drive-strength = <2>;
   bias-pull-up;
  };
 };

 pcie6a_default: pcie6a-default-state {
  clkreq-n-pins {
   pins = "gpio153";
   function = "pcie6a_clk";
   drive-strength = <2>;
   bias-pull-up;
  };

  perst-n-pins {
   pins = "gpio152";
   function = "gpio";
   drive-strength = <2>;
   bias-disable;
  };

  wake-n-pins {
   pins = "gpio154";
   function = "gpio";
   drive-strength = <2>;
   bias-pull-up;
  };
 };

 tpad_default: tpad-default-state {
  pins = "gpio3";
  function = "gpio";
  bias-pull-up;
 };

 ts0_default: ts0-default-state {
  int-n-pins {
   pins = "gpio51";
   function = "gpio";
   bias-pull-up;
  };

  reset-n-pins {
   pins = "gpio48";
   function = "gpio";
   output-high;
   drive-strength = <16>;
  };
 };

 usb_1_ss1_sbu_default: usb-1-ss1-sbu-state {
  mode-pins {
   pins = "gpio177";
   function = "gpio";
   bias-disable;
   drive-strength = <2>;
   output-high;
  };

  oe-n-pins {
   pins = "gpio179";
   function = "gpio";
   bias-disable;
   drive-strength = <2>;
  };

  sel-pins {
   pins = "gpio178";
   function = "gpio";
   bias-disable;
   drive-strength = <2>;
  };
 };

 wcd_default: wcd-reset-n-active-state {
  pins = "gpio191";
  function = "gpio";
  drive-strength = <16>;
  bias-disable;
  output-low;
 };

 wcn_sw_en: wcn-sw-en-state {
  pins = "gpio214";
  function = "gpio";
  drive-strength = <2>;
  bias-disable;
 };

 wcn_wlan_bt_en: wcn-wlan-bt-en-state {
  pins = "gpio116", "gpio117";
  function = "gpio";
  drive-strength = <2>;
  bias-disable;
 };
};

&uart14 {
 status = "okay";

 bluetooth {
  compatible = "qcom,wcn6855-bt";
  max-speed = <3200000>;

  vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
  vddaon-supply = <&vreg_pmu_aon_0p8>;
  vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
  vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
  vddbtcmx-supply = <&vreg_pmu_btcmx_0p8>;
  vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
  vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
  vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
 };
};

&usb_1_ss0_hsphy {
 vdd-supply = <&vreg_l3j_0p8>;
 vdda12-supply = <&vreg_l2j_1p2>;

 phys = <&smb2360_0_eusb2_repeater>;

 status = "okay";
};

&usb_1_ss0_qmpphy {
 vdda-phy-supply = <&vreg_l3e_1p2>;
 vdda-pll-supply = <&vreg_l1j_0p8>;

 status = "okay";
};

&usb_1_ss0 {
 status = "okay";
};

&usb_1_ss0_dwc3 {
 dr_mode = "host";
};

&usb_1_ss0_dwc3_hs {
 remote-endpoint = <&pmic_glink_ss0_hs_in>;
};

&usb_1_ss0_qmpphy_out {
 remote-endpoint = <&retimer_ss0_ss_in>;
};

&usb_1_ss1_hsphy {
 vdd-supply = <&vreg_l3j_0p8>;
 vdda12-supply = <&vreg_l2j_1p2>;

 phys = <&smb2360_1_eusb2_repeater>;

 status = "okay";
};

&usb_1_ss1_qmpphy {
 vdda-phy-supply = <&vreg_l3e_1p2>;
 vdda-pll-supply = <&vreg_l2d_0p9>;

 status = "okay";
};

&usb_1_ss1 {
 status = "okay";
};

&usb_1_ss1_dwc3 {
 dr_mode = "host";
};

&usb_1_ss1_dwc3_hs {
 remote-endpoint = <&pmic_glink_ss1_hs_in>;
};

&usb_1_ss1_qmpphy_out {
 remote-endpoint = <&pmic_glink_ss1_ss_in>;
};

&usb_mp {
 status = "okay";
};

&usb_mp_dwc3 {
 phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>;
 phy-names = "usb2-0", "usb3-0";
};

&usb_mp_hsphy0 {
 vdd-supply = <&vreg_l2e_0p8>;
 vdda12-supply = <&vreg_l3e_1p2>;

 phys = <&eusb3_repeater>;

 status = "okay";
};

&usb_mp_qmpphy0 {
 vdda-phy-supply = <&vreg_l3e_1p2>;
 vdda-pll-supply = <&vreg_l3c_0p8>;

 status = "okay";
};