Quelle  pm8941.dtsi   Sprache: unbekannt

// SPDX-License-Identifier: GPL-2.0
#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>


/ {
 thermal-zones {
  pm8941-thermal {
   polling-delay-passive = <100>;
   polling-delay = <0>;
   thermal-sensors = <&pm8941_temp>;

   trips {
    trip0 {
     temperature = <105000>;
     hysteresis = <2000>;
     type = "passive";
    };

    trip1 {
     temperature = <125000>;
     hysteresis = <2000>;
     type = "hot";
    };

    crit {
     temperature = <145000>;
     hysteresis = <2000>;
     type = "critical";
    };
   };
  };
 };
};

&spmi_bus {

 pm8941_0: pm8941@0 {
  compatible = "qcom,pm8941", "qcom,spmi-pmic";
  reg = <0x0 SPMI_USID>;
  #address-cells = <1>;
  #size-cells = <0>;

  rtc@6000 {
   compatible = "qcom,pm8941-rtc";
   reg = <0x6000>,
         <0x6100>;
   reg-names = "rtc", "alarm";
   interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
  };

  pon@800 {
   compatible = "qcom,pm8941-pon";
   reg = <0x800>;

   pwrkey {
    compatible = "qcom,pm8941-pwrkey";
    interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
    debounce = <15625>;
    bias-pull-up;
   };

   pm8941_resin: resin {
    compatible = "qcom,pm8941-resin";
    interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
    debounce = <15625>;
    bias-pull-up;
    status = "disabled";
   };
  };

  usb_id: usb-detect@900 {
   compatible = "qcom,pm8941-misc";
   reg = <0x900>;
   interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
   interrupt-names = "usb_id";
  };

  smbb: charger@1000 {
   compatible = "qcom,pm8941-charger";
   reg = <0x1000>;
   interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
   interrupt-names = "chg-done",
       "chg-fast",
       "chg-trkl",
       "bat-temp-ok",
       "bat-present",
       "chg-gone",
       "usb-valid",
       "dc-valid";

   usb-otg-in-supply = <&pm8941_5vs1>;

   status = "disabled";

   chg_otg: otg-vbus { };
  };

  pm8941_gpios: gpio@c000 {
   compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
   reg = <0xc000>;
   gpio-controller;
   gpio-ranges = <&pm8941_gpios 0 0 36>;
   #gpio-cells = <2>;
   interrupt-controller;
   #interrupt-cells = <2>;

   boost_bypass_n_pin: boost-bypass-state {
    pins = "gpio21";
    function = "normal";
   };
  };

  pm8941_mpps: mpps@a000 {
   compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp";
   reg = <0xa000>;
   gpio-controller;
   #gpio-cells = <2>;
   gpio-ranges = <&pm8941_mpps 0 0 8>;
   interrupt-controller;
   #interrupt-cells = <2>;
  };

  pm8941_temp: temp-alarm@2400 {
   compatible = "qcom,spmi-temp-alarm";
   reg = <0x2400>;
   interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
   io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
   io-channel-names = "thermal";
   #thermal-sensor-cells = <0>;
  };

  pm8941_vadc: adc@3100 {
   compatible = "qcom,spmi-vadc";
   reg = <0x3100>;
   interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
   #address-cells = <1>;
   #size-cells = <0>;
   #io-channel-cells = <1>;


   channel@6 {
    reg = <VADC_VBAT_SNS>;
   };

   channel@8 {
    reg = <VADC_DIE_TEMP>;
   };

   channel@9 {
    reg = <VADC_REF_625MV>;
   };

   channel@a {
    reg = <VADC_REF_1250MV>;
   };

   channel@e {
    reg = <VADC_GND_REF>;
   };

   channel@f {
    reg = <VADC_VDD_VADC>;
   };

   channel@30 {
    reg = <VADC_LR_MUX1_BAT_THERM>;
   };
  };

  pm8941_iadc: adc@3600 {
   compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
   reg = <0x3600>;
   interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
   qcom,external-resistor-micro-ohms = <10000>;
  };

  pm8941_coincell: charger@2800 {
   compatible = "qcom,pm8941-coincell";
   reg = <0x2800>;
   status = "disabled";
  };
 };

 pm8941_1: pm8941@1 {
  compatible = "qcom,pm8941", "qcom,spmi-pmic";
  reg = <0x1 SPMI_USID>;
  #address-cells = <1>;
  #size-cells = <0>;

  pm8941_lpg: pwm {
   compatible = "qcom,pm8941-lpg";

   #address-cells = <1>;
   #size-cells = <0>;
   #pwm-cells = <2>;

   status = "disabled";
  };

  pm8941_vib: vibrator@c000 {
   compatible = "qcom,pm8916-vib";
   reg = <0xc000>;
   status = "disabled";
  };

  pm8941_wled: wled@d800 {
   compatible = "qcom,pm8941-wled";
   reg = <0xd800>;
   label = "backlight";

   status = "disabled";
  };

  regulators {
   compatible = "qcom,pm8941-regulators";
   interrupts = <0x1 0x83 0x2 0>, <0x1 0x84 0x2 0>;
   interrupt-names = "ocp-5vs1", "ocp-5vs2";
   vin_5vs-supply = <&pm8941_5v>;

   pm8941_5v: s4 {
    regulator-min-microvolt = <5000000>;
    regulator-max-microvolt = <5000000>;
    regulator-enable-ramp-delay = <500>;
   };

   pm8941_5vs1: 5vs1 {
    regulator-enable-ramp-delay = <1000>;
    regulator-pull-down;
    regulator-over-current-protection;
    qcom,ocp-max-retries = <10>;
    qcom,ocp-retry-delay = <30>;
    qcom,vs-soft-start-strength = <0>;
    regulator-initial-mode = <1>;
   };

   pm8941_5vs2: 5vs2 {
    regulator-enable-ramp-delay = <1000>;
    regulator-pull-down;
    regulator-over-current-protection;
    qcom,ocp-max-retries = <10>;
    qcom,ocp-retry-delay = <30>;
    qcom,vs-soft-start-strength = <0>;
    regulator-initial-mode = <1>;
   };
  };
 };
};