/* SPDX-License-Identifier: GPL-2.0-only */ /* * consumer.h -- SoC Regulator consumer support. * * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. * * Author: Liam Girdwood <lrg@slimlogic.co.uk> * * Regulator Consumer Interface. * * A Power Management Regulator framework for SoC based devices. * Features:- * o Voltage and current level control. * o Operating mode control. * o Regulator status. * o sysfs entries for showing client devices and status * * EXPERIMENTAL FEATURES: * Dynamic Regulator operating Mode Switching (DRMS) - allows regulators * to use most efficient operating mode depending upon voltage and load and * is transparent to client drivers. * * e.g. Devices x,y,z share regulator r. Device x and y draw 20mA each during * IO and 1mA at idle. Device z draws 100mA when under load and 5mA when * idling. Regulator r has > 90% efficiency in NORMAL mode at loads > 100mA * but this drops rapidly to 60% when below 100mA. Regulator r has > 90% * efficiency in IDLE mode at loads < 10mA. Thus regulator r will operate * in normal mode for loads > 10mA and in IDLE mode for load <= 10mA.
*/
/* * Regulator operating modes. * * Regulators can run in a variety of different operating modes depending on * output load. This allows further system power savings by selecting the * best (and most efficient) regulator mode for a desired load. * * Most drivers will only care about NORMAL. The modes below are generic and * will probably not match the naming convention of your regulator data sheet * but should match the use cases in the datasheet. * * In order of power efficiency (least efficient at top). * * Mode Description * FAST Regulator can handle fast changes in it's load. * e.g. useful in CPU voltage & frequency scaling where * load can quickly increase with CPU frequency increases. * * NORMAL Normal regulator power supply mode. Most drivers will * use this mode. * * IDLE Regulator runs in a more efficient mode for light * loads. Can be used for devices that have a low power * requirement during periods of inactivity. This mode * may be more noisy than NORMAL and may not be able * to handle fast load switching. * * STANDBY Regulator runs in the most efficient mode for very * light loads. Can be used by devices when they are * in a sleep/standby state. This mode is likely to be * the most noisy and may not be able to handle fast load * switching. * * NOTE: Most regulators will only support a subset of these modes. Some * will only just support NORMAL. * * These modes can be OR'ed together to make up a mask of valid register modes.
*/
/* * Regulator errors that can be queried using regulator_get_error_flags * * UNDER_VOLTAGE Regulator output is under voltage. * OVER_CURRENT Regulator output current is too high. * REGULATION_OUT Regulator output is out of regulation. * FAIL Regulator output has failed. * OVER_TEMP Regulator over temp. * * NOTE: These errors can be OR'ed together.
*/
/** * struct pre_voltage_change_data - Data sent with PRE_VOLTAGE_CHANGE event * * @old_uV: Current voltage before change. * @min_uV: Min voltage we'll change to. * @max_uV: Max voltage we'll change to.
*/ struct pre_voltage_change_data { unsignedlong old_uV; unsignedlong min_uV; unsignedlong max_uV;
};
struct regulator;
/** * struct regulator_bulk_data - Data used for bulk regulator operations. * * @supply: The name of the supply. Initialised by the user before * using the bulk regulator APIs. * @consumer: The regulator consumer for the supply. This will be managed * by the bulk API. * @init_load_uA: After getting the regulator, regulator_set_load() will be * called with this load. Initialised by the user before * using the bulk regulator APIs. * * The regulator APIs provide a series of regulator_bulk_() API calls as * a convenience to consumers which require multiple supplies. This * structure is used to manage data for these calls.
*/ struct regulator_bulk_data { constchar *supply; struct regulator *consumer; int init_load_uA;
int devm_regulator_bulk_register_supply_alias(struct device *dev, constchar *const *id, struct device *alias_dev, constchar *const *alias_id, int num_id);
/* regulator output control and status */ int __must_check regulator_enable(struct regulator *regulator); int regulator_disable(struct regulator *regulator); int regulator_force_disable(struct regulator *regulator); int regulator_is_enabled(struct regulator *regulator); int regulator_disable_deferred(struct regulator *regulator, int ms);
int __must_check regulator_bulk_get(struct device *dev, int num_consumers, struct regulator_bulk_data *consumers); int __must_check devm_regulator_bulk_get(struct device *dev, int num_consumers, struct regulator_bulk_data *consumers); void devm_regulator_bulk_put(struct regulator_bulk_data *consumers); int __must_check devm_regulator_bulk_get_exclusive(struct device *dev, int num_consumers, struct regulator_bulk_data *consumers); int __must_check devm_regulator_bulk_get_const( struct device *dev, int num_consumers, conststruct regulator_bulk_data *in_consumers, struct regulator_bulk_data **out_consumers); int __must_check regulator_bulk_enable(int num_consumers, struct regulator_bulk_data *consumers); int devm_regulator_bulk_get_enable(struct device *dev, int num_consumers, constchar * const *id); int regulator_bulk_disable(int num_consumers, struct regulator_bulk_data *consumers); int regulator_bulk_force_disable(int num_consumers, struct regulator_bulk_data *consumers); void regulator_bulk_free(int num_consumers, struct regulator_bulk_data *consumers);
int regulator_count_voltages(struct regulator *regulator); int regulator_list_voltage(struct regulator *regulator, unsigned selector); int regulator_is_supported_voltage(struct regulator *regulator, int min_uV, int max_uV); unsignedint regulator_get_linear_step(struct regulator *regulator); int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV); int regulator_set_voltage_time(struct regulator *regulator, int old_uV, int new_uV); int regulator_get_voltage(struct regulator *regulator); int regulator_sync_voltage(struct regulator *regulator); int regulator_set_current_limit(struct regulator *regulator, int min_uA, int max_uA); int regulator_get_current_limit(struct regulator *regulator); int regulator_get_unclaimed_power_budget(struct regulator *regulator); int regulator_request_power_budget(struct regulator *regulator, unsignedint pw_req); void regulator_free_power_budget(struct regulator *regulator, unsignedint pw);
int regulator_set_mode(struct regulator *regulator, unsignedint mode); unsignedint regulator_get_mode(struct regulator *regulator); int regulator_get_error_flags(struct regulator *regulator, unsignedint *flags); int regulator_set_load(struct regulator *regulator, int load_uA);
int regulator_allow_bypass(struct regulator *regulator, bool allow);
struct regmap *regulator_get_regmap(struct regulator *regulator); int regulator_get_hardware_vsel_register(struct regulator *regulator, unsigned *vsel_reg, unsigned *vsel_mask); int regulator_list_hardware_vsel(struct regulator *regulator, unsigned selector); int regulator_hardware_enable(struct regulator *regulator, bool enable);
/* * Make sure client drivers will still build on systems with no software * controllable voltage or current regulators.
*/ staticinlinestruct regulator *__must_check regulator_get(struct device *dev, constchar *id)
{ /* Nothing except the stubbed out regulator API should be * looking at the value except to check if it is an error * value. Drivers are free to handle NULL specifically by * skipping all regulator API calls, but they don't have to. * Drivers which don't, should make sure they properly handle * corner cases of the API, such as regulator_get_voltage() * returning 0.
*/ return NULL;
}
staticinlineint regulator_set_voltage_triplet(struct regulator *regulator, int min_uV, int target_uV, int max_uV)
{ if (regulator_set_voltage(regulator, target_uV, max_uV) == 0) return 0;
Die Informationen auf dieser Webseite wurden
nach bestem Wissen sorgfältig zusammengestellt. Es wird jedoch weder Vollständigkeit, noch Richtigkeit,
noch Qualität der bereit gestellten Informationen zugesichert.
Bemerkung:
Die farbliche Syntaxdarstellung und die Messung sind noch experimentell.