staticint gen6_check_mailbox_status(u32 mbox)
{ switch (mbox & GEN6_PCODE_ERROR_MASK) { case GEN6_PCODE_SUCCESS: return 0; case GEN6_PCODE_UNIMPLEMENTED_CMD: return -ENODEV; case GEN6_PCODE_ILLEGAL_CMD: return -ENXIO; case GEN6_PCODE_MIN_FREQ_TABLE_GT_RATIO_OUT_OF_RANGE: case GEN7_PCODE_MIN_FREQ_TABLE_GT_RATIO_OUT_OF_RANGE: return -EOVERFLOW; case GEN6_PCODE_TIMEOUT: return -ETIMEDOUT; default:
MISSING_CASE(mbox & GEN6_PCODE_ERROR_MASK); return 0;
}
}
staticint gen7_check_mailbox_status(u32 mbox)
{ switch (mbox & GEN6_PCODE_ERROR_MASK) { case GEN6_PCODE_SUCCESS: return 0; case GEN6_PCODE_ILLEGAL_CMD: return -ENXIO; case GEN7_PCODE_TIMEOUT: return -ETIMEDOUT; case GEN7_PCODE_ILLEGAL_DATA: return -EINVAL; case GEN11_PCODE_ILLEGAL_SUBCOMMAND: return -ENXIO; case GEN11_PCODE_LOCKED: return -EBUSY; case GEN11_PCODE_REJECTED: return -EACCES; case GEN7_PCODE_MIN_FREQ_TABLE_GT_RATIO_OUT_OF_RANGE: return -EOVERFLOW; default:
MISSING_CASE(mbox & GEN6_PCODE_ERROR_MASK); return 0;
}
}
staticint __snb_pcode_rw(struct intel_uncore *uncore, u32 mbox,
u32 *val, u32 *val1, int fast_timeout_us, int slow_timeout_ms, bool is_read)
{
lockdep_assert_held(&uncore->i915->sb_lock);
/* * GEN6_PCODE_* are outside of the forcewake domain, we can use * intel_uncore_read/write_fw variants to reduce the amount of work * required when reading/writing.
*/
if (intel_uncore_read_fw(uncore, GEN6_PCODE_MAILBOX) & GEN6_PCODE_READY) return -EAGAIN;
/** * skl_pcode_request - send PCODE request until acknowledgment * @uncore: uncore * @mbox: PCODE mailbox ID the request is targeted for * @request: request ID * @reply_mask: mask used to check for request acknowledgment * @reply: value used to check for request acknowledgment * @timeout_base_ms: timeout for polling with preemption enabled * * Keep resending the @request to @mbox until PCODE acknowledges it, PCODE * reports an error or an overall timeout of @timeout_base_ms+50 ms expires. * The request is acknowledged once the PCODE reply dword equals @reply after * applying @reply_mask. Polling is first attempted with preemption enabled * for @timeout_base_ms and if this times out for another 50 ms with * preemption disabled. * * Returns 0 on success, %-ETIMEDOUT in case of a timeout, <0 in case of some * other error as reported by PCODE.
*/ int skl_pcode_request(struct intel_uncore *uncore, u32 mbox, u32 request,
u32 reply_mask, u32 reply, int timeout_base_ms)
{
u32 status; int ret;
/* * Prime the PCODE by doing a request first. Normally it guarantees * that a subsequent request, at most @timeout_base_ms later, succeeds. * _wait_for() doesn't guarantee when its passed condition is evaluated * first, so send the first request explicitly.
*/ if (COND) {
ret = 0; goto out;
}
ret = _wait_for(COND, timeout_base_ms * 1000, 10, 10); if (!ret) goto out;
/* * The above can time out if the number of requests was low (2 in the * worst case) _and_ PCODE was busy for some reason even after a * (queued) request and @timeout_base_ms delay. As a workaround retry * the poll with preemption disabled to maximize the number of * requests. Increase the timeout from @timeout_base_ms to 50ms to * account for interrupts that could reduce the number of these * requests, and for any quirks of the PCODE firmware that delays * the request completion.
*/
drm_dbg_kms(&uncore->i915->drm, "PCODE timeout, retrying with preemption disabled\n");
drm_WARN_ON_ONCE(&uncore->i915->drm, timeout_base_ms > 3);
preempt_disable();
ret = wait_for_atomic(COND, 50);
preempt_enable();
out:
mutex_unlock(&uncore->i915->sb_lock); return status ? status : ret; #undef COND
}
staticint pcode_init_wait(struct intel_uncore *uncore, int timeout_ms)
{ if (__intel_wait_for_register_fw(uncore,
GEN6_PCODE_MAILBOX,
GEN6_PCODE_READY, 0,
500, timeout_ms,
NULL)) return -EPROBE_DEFER;
Die Informationen auf dieser Webseite wurden
nach bestem Wissen sorgfältig zusammengestellt. Es wird jedoch weder Vollständigkeit, noch Richtigkeit,
noch Qualität der bereit gestellten Informationen zugesichert.
Bemerkung:
Die farbliche Syntaxdarstellung und die Messung sind noch experimentell.