Quelle  sm8350-hdk.dts   Sprache: unbekannt

// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2020-2021, Linaro Limited
 */

/dts-v1/;

#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sm8350.dtsi"
#include "pm8350.dtsi"
#include "pm8350b.dtsi"
#include "pm8350c.dtsi"
#include "pmk8350.dtsi"
#include "pmr735a.dtsi"
#include "pmr735b.dtsi"

/ {
 model = "Qualcomm Technologies, Inc. SM8350 HDK";
 compatible = "qcom,sm8350-hdk", "qcom,sm8350";
 chassis-type = "embedded";

 aliases {
  serial0 = &uart2;
 };

 chosen {
  stdout-path = "serial0:115200n8";
 };

 hdmi-connector {
  compatible = "hdmi-connector";
  type = "a";

  port {
   hdmi_con: endpoint {
    remote-endpoint = <<9611_out>;
   };
  };
 };

 pmic-glink {
  compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
  #address-cells = <1>;
  #size-cells = <0>;
  orientation-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;

  connector@0 {
   compatible = "usb-c-connector";
   reg = <0>;
   power-role = "dual";
   data-role = "dual";

   ports {
    #address-cells = <1>;
    #size-cells = <0>;

    port@0 {
     reg = <0>;

     pmic_glink_hs_in: endpoint {
      remote-endpoint = <&usb_1_dwc3_hs>;
     };
    };

    port@1 {
     reg = <1>;

     pmic_glink_ss_in: endpoint {
      remote-endpoint = <&usb_1_qmpphy_out>;
     };
    };

    port@2 {
     reg = <2>;

     pmic_glink_sbu: endpoint {
      remote-endpoint = <&fsa4480_sbu_mux>;
     };
    };
   };
  };
 };

 vph_pwr: vph-pwr-regulator {
  compatible = "regulator-fixed";
  regulator-name = "vph_pwr";
  regulator-min-microvolt = <3700000>;
  regulator-max-microvolt = <3700000>;

  regulator-always-on;
  regulator-boot-on;
 };

 lt9611_1v2: lt9611-1v2-regulator {
  compatible = "regulator-fixed";
  regulator-name = "LT9611_1V2";

  vin-supply = <&vph_pwr>;
  regulator-min-microvolt = <1200000>;
  regulator-max-microvolt = <1200000>;
  gpio = <&tlmm 49 GPIO_ACTIVE_HIGH>;
  enable-active-high;
  regulator-boot-on;
 };

 lt9611_3v3: lt9611-3v3-regulator {
  compatible = "regulator-fixed";
  regulator-name = "LT9611_3V3";

  vin-supply = <&vreg_bob>;
  gpio = <&tlmm 47 GPIO_ACTIVE_HIGH>;
  regulator-min-microvolt = <3300000>;
  regulator-max-microvolt = <3300000>;
  enable-active-high;
  regulator-boot-on;
  regulator-always-on;
 };
};

&adsp {
 status = "okay";
 firmware-name = "qcom/sm8350/adsp.mbn";
};

&apps_rsc {
 regulators-0 {
  compatible = "qcom,pm8350-rpmh-regulators";
  qcom,pmic-id = "b";

  vdd-s1-supply = <&vph_pwr>;
  vdd-s2-supply = <&vph_pwr>;
  vdd-s3-supply = <&vph_pwr>;
  vdd-s4-supply = <&vph_pwr>;
  vdd-s5-supply = <&vph_pwr>;
  vdd-s6-supply = <&vph_pwr>;
  vdd-s7-supply = <&vph_pwr>;
  vdd-s8-supply = <&vph_pwr>;
  vdd-s9-supply = <&vph_pwr>;
  vdd-s10-supply = <&vph_pwr>;
  vdd-s11-supply = <&vph_pwr>;
  vdd-s12-supply = <&vph_pwr>;

  vdd-l1-l4-supply = <&vreg_s11b_0p95>;
  vdd-l2-l7-supply = <&vreg_bob>;
  vdd-l3-l5-supply = <&vreg_bob>;
  vdd-l6-l9-l10-supply = <&vreg_s11b_0p95>;

  vreg_s10b_1p8: smps10 {
   regulator-name = "vreg_s10b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s11b_0p95: smps11 {
   regulator-name = "vreg_s11b_0p95";
   regulator-min-microvolt = <952000>;
   regulator-max-microvolt = <952000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s12b_1p25: smps12 {
   regulator-name = "vreg_s12b_1p25";
   regulator-min-microvolt = <1256000>;
   regulator-max-microvolt = <1256000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l1b_0p88: ldo1 {
   regulator-name = "vreg_l1b_0p88";
   regulator-min-microvolt = <912000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2b_3p07: ldo2 {
   regulator-name = "vreg_l2b_3p07";
   regulator-min-microvolt = <3072000>;
   regulator-max-microvolt = <3072000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3b_0p9: ldo3 {
   regulator-name = "vreg_l3b_0p9";
   regulator-min-microvolt = <904000>;
   regulator-max-microvolt = <904000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l5b_0p88: ldo5 {
   regulator-name = "vreg_l5b_0p88";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <888000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l6b_1p2: ldo6 {
   regulator-name = "vreg_l6b_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1208000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l7b_2p96: ldo7 {
   regulator-name = "vreg_l7b_2p96";
   regulator-min-microvolt = <2504000>;
   regulator-max-microvolt = <2504000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l9b_1p2: ldo9 {
   regulator-name = "vreg_l9b_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-1 {
  compatible = "qcom,pm8350c-rpmh-regulators";
  qcom,pmic-id = "c";

  vdd-s1-supply = <&vph_pwr>;
  vdd-s2-supply = <&vph_pwr>;
  vdd-s3-supply = <&vph_pwr>;
  vdd-s4-supply = <&vph_pwr>;
  vdd-s5-supply = <&vph_pwr>;
  vdd-s6-supply = <&vph_pwr>;
  vdd-s7-supply = <&vph_pwr>;
  vdd-s8-supply = <&vph_pwr>;
  vdd-s9-supply = <&vph_pwr>;
  vdd-s10-supply = <&vph_pwr>;

  vdd-l1-l12-supply = <&vreg_s1c_1p86>;
  vdd-l2-l8-supply = <&vreg_s1c_1p86>;
  vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
  vdd-l6-l9-l11-supply = <&vreg_bob>;
  vdd-l10-supply = <&vreg_s12b_1p25>;

  vdd-bob-supply = <&vph_pwr>;

  vreg_s1c_1p86: smps1 {
   regulator-name = "vreg_s1c_1p86";
   regulator-min-microvolt = <1856000>;
   regulator-max-microvolt = <1880000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_bob: bob {
   regulator-name = "vreg_bob";
   regulator-min-microvolt = <3008000>;
   regulator-max-microvolt = <3960000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
  };

  vreg_l1c_1p8: ldo1 {
   regulator-name = "vreg_l1c_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2c_1p8: ldo2 {
   regulator-name = "vreg_l2c_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l6c_1p8: ldo6 {
   regulator-name = "vreg_l6c_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <2960000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l9c_2p96: ldo9 {
   regulator-name = "vreg_l9c_2p96";
   regulator-min-microvolt = <2960000>;
   regulator-max-microvolt = <3008000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l10c_1p2: ldo10 {
   regulator-name = "vreg_l10c_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-2 {
  compatible = "qcom,pmr735a-rpmh-regulators";
  qcom,pmic-id = "e";

  vdd-s1-supply = <&vph_pwr>;
  vdd-s2-supply = <&vph_pwr>;
  vdd-s3-supply = <&vph_pwr>;

  vdd-l1-l2-supply = <&vreg_s2e_0p85>;
  vdd-l3-supply = <&vreg_s1e_1p25>;
  vdd-l4-supply = <&vreg_s1c_1p86>;
  vdd-l5-l6-supply = <&vreg_s1c_1p86>;
  vdd-l7-bob-supply = <&vreg_bob>;

  vreg_s1e_1p25: smps1 {
   regulator-name = "vreg_s1e_1p25";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1280000>;
  };

  vreg_s2e_0p85: smps2 {
   regulator-name = "vreg_s2e_0p85";
   regulator-min-microvolt = <950000>;
   regulator-max-microvolt = <976000>;
  };

  vreg_s3e_2p20: smps3 {
   regulator-name = "vreg_s3e_2p20";
   regulator-min-microvolt = <2200000>;
   regulator-max-microvolt = <2352000>;
  };

  vreg_l1e_0p9: ldo1 {
   regulator-name = "vreg_l1e_0p9";
   regulator-min-microvolt = <912000>;
   regulator-max-microvolt = <912000>;
  };

  vreg_l2e_1p2: ldo2 {
   regulator-name = "vreg_l2e_0p8";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
  };

  vreg_l3e_1p2: ldo3 {
   regulator-name = "vreg_l3e_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
  };

  vreg_l4e_1p7: ldo4 {
   regulator-name = "vreg_l4e_1p7";
   regulator-min-microvolt = <1776000>;
   regulator-max-microvolt = <1872000>;
  };

  vreg_l5e_0p8: ldo5 {
   regulator-name = "vreg_l5e_0p8";
   regulator-min-microvolt = <800000>;
   regulator-max-microvolt = <800000>;
  };

  vreg_l6e_0p8: ldo6 {
   regulator-name = "vreg_l6e_0p8";
   regulator-min-microvolt = <480000>;
   regulator-max-microvolt = <904000>;
  };

  vreg_l7e_2p8: ldo7 {
   regulator-name = "vreg_l7e_2p8";
   regulator-min-microvolt = <2800000>;
   regulator-max-microvolt = <2800000>;
  };
 };
};

&cdsp {
 status = "okay";
 firmware-name = "qcom/sm8350/cdsp.mbn";
};

&mdss_dsi0 {
 vdda-supply = <&vreg_l6b_1p2>;
 status = "okay";

 ports {
  port@1 {
   endpoint {
    remote-endpoint = <<9611_a>;
    data-lanes = <0 1 2 3>;
   };
  };
 };
};

&mdss_dsi0_phy  {
 vdds-supply = <&vreg_l5b_0p88>;
 status = "okay";
};

&gpi_dma1 {
 status = "okay";
};

&gpu {
 status = "okay";

 zap-shader {
  firmware-name = "qcom/sm8350/a660_zap.mbn";
 };
};

&i2c13 {
 clock-frequency = <100000>;

 status = "okay";

 typec-mux@42 {
  compatible = "fcs,fsa4480";
  reg = <0x42>;

  interrupts-extended = <&tlmm 2 IRQ_TYPE_LEVEL_LOW>;

  vcc-supply = <&vreg_bob>;
  mode-switch;
  orientation-switch;

  port {
   fsa4480_sbu_mux: endpoint {
    remote-endpoint = <&pmic_glink_sbu>;
   };
  };
 };
};

&i2c15 {
 clock-frequency = <400000>;
 status = "okay";

 lt9611_codec: hdmi-bridge@2b {
  compatible = "lontium,lt9611uxc";
  reg = <0x2b>;

  interrupts-extended = <&tlmm 50 IRQ_TYPE_EDGE_FALLING>;
  reset-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;

  vdd-supply = <<9611_1v2>;
  vcc-supply = <<9611_3v3>;

  pinctrl-names = "default";
  pinctrl-0 = <<9611_state>;

  ports {
   #address-cells = <1>;
   #size-cells = <0>;

   port@0 {
    reg = <0>;

    lt9611_a: endpoint {
     remote-endpoint = <&mdss_dsi0_out>;
    };
   };

   port@2 {
    reg = <2>;

    lt9611_out: endpoint {
     remote-endpoint = <&hdmi_con>;
    };
   };
  };
 };
};

&mdss {
 status = "okay";
};

&mdss_dp {
 status = "okay";
};

&mdss_dp_out {
 data-lanes = <0 1>;
};

&mpss {
 status = "okay";
 firmware-name = "qcom/sm8350/modem.mbn";
};

&pcie0 {
 pinctrl-names = "default";
 pinctrl-0 = <&pcie0_default_state>;

 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
 wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;

 status = "okay";
};

&pcie0_phy {
 vdda-phy-supply = <&vreg_l5b_0p88>;
 vdda-pll-supply = <&vreg_l6b_1p2>;

 status = "okay";
};

&pcie1 {
 perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
 wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;

 pinctrl-names = "default";
 pinctrl-0 = <&pcie1_default_state>;

 status = "okay";
};

&pcie1_phy {
 status = "okay";
 vdda-phy-supply = <&vreg_l5b_0p88>;
 vdda-pll-supply = <&vreg_l6b_1p2>;
};

&qupv3_id_0 {
 status = "okay";
};

&qupv3_id_1 {
 status = "okay";
};

&qupv3_id_2 {
 status = "okay";
};

&sdhc_2 {
 cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>;
 pinctrl-names = "default", "sleep";
 pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
 pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_n>;
 vmmc-supply = <&vreg_l9c_2p96>;
 vqmmc-supply = <&vreg_l6c_1p8>;
 no-sdio;
 no-mmc;
 status = "okay";
};

&slpi {
 status = "okay";
 firmware-name = "qcom/sm8350/slpi.mbn";
};

&tlmm {
 gpio-reserved-ranges = <52 8>;

 gpio-line-names =
  "APPS_I2C_SDA", /* GPIO_0 */
  "APPS_I2C_SCL",
  "FSA_INT_N",
  "USER_LED3_EN",
  "SMBUS_SDA_1P8",
  "SMBUS_SCL_1P8",
  "2M2_3P3_EN",
  "ALERT_DUAL_M2_N",
  "EXP_UART_CTS",
  "EXP_UART_RFR",
  "EXP_UART_TX", /* GPIO_10 */
  "EXP_UART_RX",
  "NC",
  "NC",
  "RCM_MARKER1",
  "WSA0_EN",
  "CAM1_RESET_N",
  "CAM0_RESET_N",
  "DEBUG_UART_TX",
  "DEBUG_UART_RX",
  "TS_I2C_SDA", /* GPIO_20 */
  "TS_I2C_SCL",
  "TS_RESET_N",
  "TS_INT_N",
  "DISP0_RESET_N",
  "DISP1_RESET_N",
  "ETH_RESET",
  "RCM_MARKER2",
  "CAM_DC_MIPI_MUX_EN",
  "CAM_DC_MIPI_MUX_SEL",
  "AFC_PHY_TA_D_PLUS", /* GPIO_30 */
  "AFC_PHY_TA_D_MINUS",
  "PM8008_1_IRQ",
  "PM8008_1_RESET_N",
  "PM8008_2_IRQ",
  "PM8008_2_RESET_N",
  "CAM_DC_I3C_SDA",
  "CAM_DC_I3C_SCL",
  "FP_INT_N",
  "FP_WUHB_INT_N",
  "SMB_SPMI_DATA", /* GPIO_40 */
  "SMB_SPMI_CLK",
  "USB_HUB_RESET",
  "FORCE_USB_BOOT",
  "LRF_IRQ",
  "NC",
  "IMU2_INT",
  "HDMI_3P3_EN",
  "HDMI_RSTN",
  "HDMI_1P2_EN",
  "HDMI_INT", /* GPIO_50 */
  "USB1_ID",
  "FP_SPI_MISO",
  "FP_SPI_MOSI",
  "FP_SPI_CLK",
  "FP_SPI_CS_N",
  "NFC_ESE_SPI_MISO",
  "NFC_ESE_SPI_MOSI",
  "NFC_ESE_SPI_CLK",
  "NFC_ESE_SPI_CS",
  "NFC_I2C_SDA", /* GPIO_60 */
  "NFC_I2C_SCLC",
  "NFC_EN",
  "NFC_CLK_REQ",
  "HST_WLAN_EN",
  "HST_BT_EN",
  "HST_SW_CTRL",
  "NC",
  "HST_BT_UART_CTS",
  "HST_BT_UART_RFR",
  "HST_BT_UART_TX", /* GPIO_70 */
  "HST_BT_UART_RX",
  "CAM_DC_SPI0_MISO",
  "CAM_DC_SPI0_MOSI",
  "CAM_DC_SPI0_CLK",
  "CAM_DC_SPI0_CS_N",
  "CAM_DC_SPI1_MISO",
  "CAM_DC_SPI1_MOSI",
  "CAM_DC_SPI1_CLK",
  "CAM_DC_SPI1_CS_N",
  "HALL_INT_N", /* GPIO_80 */
  "USB_PHY_PS",
  "MDP_VSYNC_P",
  "MDP_VSYNC_S",
  "ETH_3P3_EN",
  "RADAR_INT",
  "NFC_DWL_REQ",
  "SM_GPIO_87",
  "WCD_RESET_N",
  "ALSP_INT_N",
  "PRESS_INT", /* GPIO_90 */
  "SAR_INT_N",
  "SD_CARD_DET_N",
  "NC",
  "PCIE0_RESET_N",
  "PCIE0_CLK_REQ_N",
  "PCIE0_WAKE_N",
  "PCIE1_RESET_N",
  "PCIE1_CLK_REQ_N",
  "PCIE1_WAKE_N",
  "CAM_MCLK0", /* GPIO_100 */
  "CAM_MCLK1",
  "CAM_MCLK2",
  "CAM_MCLK3",
  "CAM_MCLK4",
  "CAM_MCLK5",
  "CAM2_RESET_N",
  "CCI_I2C0_SDA",
  "CCI_I2C0_SCL",
  "CCI_I2C1_SDA",
  "CCI_I2C1_SCL", /* GPIO_110 */
  "CCI_I2C2_SDA",
  "CCI_I2C2_SCL",
  "CCI_I2C3_SDA",
  "CCI_I2C3_SCL",
  "CAM5_RESET_N",
  "CAM4_RESET_N",
  "CAM3_RESET_N",
  "IMU1_INT",
  "MAG_INT_N",
  "MI2S2_I2S_SCK", /* GPIO_120 */
  "MI2S2_I2S_DAT0",
  "MI2S2_I2S_WS",
  "HIFI_DAC_I2S_MCLK",
  "MI2S2_I2S_DAT1",
  "HIFI_DAC_I2S_SCK",
  "HIFI_DAC_I2S_DAT0",
  "NC",
  "HIFI_DAC_I2S_WS",
  "HST_BT_WLAN_SLIMBUS_CLK",
  "HST_BT_WLAN_SLIMBUS_DAT0", /* GPIO_130 */
  "BT_LED_EN",
  "WLAN_LED_EN",
  "NC",
  "NC",
  "NC",
  "UIM2_PRESENT",
  "NC",
  "NC",
  "NC",
  "UIM1_PRESENT", /* GPIO_140 */
  "NC",
  "SM_RFFE0_DATA",
  "NC",
  "SM_RFFE1_DATA",
  "SM_MSS_GRFC4",
  "SM_MSS_GRFC5",
  "SM_MSS_GRFC6",
  "SM_MSS_GRFC7",
  "SM_RFFE4_CLK",
  "SM_RFFE4_DATA", /* GPIO_150 */
  "WLAN_COEX_UART1_RX",
  "WLAN_COEX_UART1_TX",
  "HST_SW_CTRL",
  "DSI0_STATUS",
  "DSI1_STATUS",
  "APPS_PBL_BOOT_SPEED_1",
  "APPS_BOOT_FROM_ROM",
  "APPS_PBL_BOOT_SPEED_0",
  "QLINK0_REQ",
  "QLINK0_EN", /* GPIO_160 */
  "QLINK0_WMSS_RESET_N",
  "NC",
  "NC",
  "NC",
  "NC",
  "NC",
  "NC",
  "WCD_SWR_TX_CLK",
  "WCD_SWR_TX_DATA0",
  "WCD_SWR_TX_DATA1", /* GPIO_170 */
  "WCD_SWR_RX_CLK",
  "WCD_SWR_RX_DATA0",
  "WCD_SWR_RX_DATA1",
  "DMIC01_CLK",
  "DMIC01_DATA",
  "DMIC23_CLK",
  "DMIC23_DATA",
  "WSA_SWR_CLK",
  "WSA_SWR_DATA",
  "DMIC45_CLK", /* GPIO_180 */
  "DMIC45_DATA",
  "WCD_SWR_TX_DATA2",
  "SENSOR_I3C_SDA",
  "SENSOR_I3C_SCL",
  "CAM_OIS0_I3C_SDA",
  "CAM_OIS0_I3C_SCL",
  "IMU_SPI_MISO",
  "IMU_SPI_MOSI",
  "IMU_SPI_CLK",
  "IMU_SPI_CS_N", /* GPIO_190 */
  "MAG_I2C_SDA",
  "MAG_I2C_SCL",
  "SENSOR_I2C_SDA",
  "SENSOR_I2C_SCL",
  "RADAR_SPI_MISO",
  "RADAR_SPI_MOSI",
  "RADAR_SPI_CLK",
  "RADAR_SPI_CS_N",
  "HST_BLE_UART_TX",
  "HST_BLE_UART_RX", /* GPIO_200 */
  "HST_WLAN_UART_TX",
  "HST_WLAN_UART_RX";

 pcie0_default_state: pcie0-default-state {
  perst-pins {
   pins = "gpio94";
   function = "gpio";
   drive-strength = <2>;
   bias-pull-down;
  };

  clkreq-pins {
   pins = "gpio95";
   function = "pcie0_clkreqn";
   drive-strength = <2>;
   bias-pull-up;
  };

  wake-pins {
   pins = "gpio96";
   function = "gpio";
   drive-strength = <2>;
   bias-pull-up;
  };
 };

 pcie1_default_state: pcie1-default-state {
  perst-pins {
   pins = "gpio97";
   function = "gpio";
   drive-strength = <2>;
   bias-pull-down;
  };

  clkreq-pins {
   pins = "gpio98";
   function = "pcie1_clkreqn";
   drive-strength = <2>;
   bias-pull-up;
  };

  wake-pins {
   pins = "gpio99";
   function = "gpio";
   drive-strength = <2>;
   bias-pull-up;
  };
 };

 sdc2_card_det_n: sd-card-det-n-state {
  pins = "gpio92";
  function = "gpio";
  drive-strength = <2>;
  bias-pull-up;
 };
};

&uart2 {
 status = "okay";
};

&ufs_mem_hc {
 status = "okay";

 reset-gpios = <&tlmm 203 GPIO_ACTIVE_LOW>;

 vcc-supply = <&vreg_l7b_2p96>;
 vcc-max-microamp = <800000>;
 vccq-supply = <&vreg_l9b_1p2>;
 vccq-max-microamp = <900000>;
 vdd-hba-supply = <&vreg_l9b_1p2>;
};

&ufs_mem_phy {
 status = "okay";

 vdda-phy-supply = <&vreg_l5b_0p88>;
 vdda-pll-supply = <&vreg_l6b_1p2>;
};

&usb_1 {
 status = "okay";
};

&usb_1_dwc3 {
 dr_mode = "otg";
 usb-role-switch;
};

&usb_1_dwc3_hs {
 remote-endpoint = <&pmic_glink_hs_in>;
};

&usb_1_hsphy {
 status = "okay";

 vdda-pll-supply = <&vreg_l5b_0p88>;
 vdda18-supply = <&vreg_l1c_1p8>;
 vdda33-supply = <&vreg_l2b_3p07>;
};

&usb_1_qmpphy {
 status = "okay";

 vdda-phy-supply = <&vreg_l6b_1p2>;
 vdda-pll-supply = <&vreg_l1b_0p88>;
};

&usb_1_qmpphy_out {
 remote-endpoint = <&pmic_glink_ss_in>;
};

&usb_2 {
 status = "okay";
};

&usb_2_dwc3 {
 dr_mode = "host";

 pinctrl-names = "default";
 pinctrl-0 = <&usb_hub_enabled_state>;
};

&usb_2_hsphy {
 status = "okay";

 vdda-pll-supply = <&vreg_l5b_0p88>;
 vdda18-supply = <&vreg_l1c_1p8>;
 vdda33-supply = <&vreg_l2b_3p07>;
};

&usb_2_qmpphy {
 status = "okay";

 vdda-phy-supply = <&vreg_l6b_1p2>;
 vdda-pll-supply = <&vreg_l5b_0p88>;
};

/* PINCTRL - additions to nodes defined in sm8350.dtsi */

&tlmm {
 usb_hub_enabled_state: usb-hub-enabled-state {
  pins = "gpio42";
  function = "gpio";

  drive-strength = <2>;
  output-low;
 };

 lt9611_state: lt9611-state {
  rst-pins {
   pins = "gpio48";
   function = "gpio";

   output-high;
   input-disable;
  };

  irq-pins {
   pins = "gpio50";
   function = "gpio";
   bias-disable;
  };
 };
};

&ipa {
 qcom,gsi-loader = "self";
 memory-region = <&pil_ipa_fw_mem>;
 status = "okay";
 firmware-name = "qcom/sm8350/ipa_fws.mbn";
};