// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Device Tree file for Marvell Armada 370 evaluation board
* (DB-88F6710-BP-DDR3)
*
* Copyright (C) 2012 Marvell
*
* Lior Amsalem <alior@marvell.com>
* Gregory CLEMENT <gregory.clement@free-electrons.com>
* Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
*
* Note: this Device Tree assumes that the bootloader has remapped the
* internal registers to 0xf1000000 (instead of the default
* 0xd0000000). The 0xf1000000 is the default used by the recent,
* DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
* boards were delivered with an older version of the bootloader that
* left internal registers mapped at 0xd0000000. If you are in this
* situation, you should either update your bootloader (preferred
* solution) or the below Device Tree should be adjusted.
*/
/dts-v1/;
#include "armada-370.dtsi"
/ {
model = "Marvell Armada 370 Evaluation Board";
compatible = "marvell,a370-db", "marvell,armada370", "marvell,armada-370-xp";
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x00000000 0x40000000>; /* 1 GB */
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
internal-regs {
serial@12000 {
status = "okay";
};
sata@a0000 {
nr-ports = <2>;
status = "okay";
};
ethernet@70000 {
pinctrl-0 = <&ge0_rgmii_pins>;
pinctrl-names = "default";
status = "okay";
phy = <&phy0>;
phy-mode = "rgmii-id";
};
ethernet@74000 {
pinctrl-0 = <&ge1_rgmii_pins>;
pinctrl-names = "default";
status = "okay";
phy = <&phy1>;
phy-mode = "rgmii-id";
};
i2c@11000 {
pinctrl-0 = <&i2c0_pins>;
pinctrl-names = "default";
clock-frequency = <100000>;
status = "okay";
audio_codec: audio-codec@4a {
#sound-dai-cells = <0>;
compatible = "cirrus,cs42l51";
reg = <0x4a>;
};
};
audio-controller@30000 {
pinctrl-0 = <&i2s_pins2>;
pinctrl-names = "default";
status = "okay";
};
mvsdio@d4000 {
pinctrl-0 = <&sdio_pins1>;
pinctrl-names = "default";
/*
* This device is disabled by default, because
* using the SD card connector requires
* changing the default CON40 connector
* "DB-88F6710_MPP_2xRGMII_DEVICE_Jumper" to a
* different connector
* "DB-88F6710_MPP_RGMII_SD_Jumper".
*/
status = "disabled";
/* No CD or WP GPIOs */
broken-cd;
};
usb@50000 {
status = "okay";
};
usb@51000 {
status = "okay";
};
};
};
sound {
compatible = "simple-audio-card";
simple-audio-card,name = "Armada 370 DB Audio";
simple-audio-card,mclk-fs = <256>;
simple-audio-card,widgets =
"Headphone", "Out Jack",
"Line", "In Jack";
simple-audio-card,routing =
"Out Jack", "HPL",
"Out Jack", "HPR",
"AIN1L", "In Jack",
"AIN1R", "In Jack";
status = "okay";
simple-audio-card,dai-link@0 {
format = "i2s";
cpu {
sound-dai = <&audio_controller 0>;
};
codec {
sound-dai = <&audio_codec>;
};
};
simple-audio-card,dai-link@1 {
format = "i2s";
cpu {
sound-dai = <&audio_controller 1>;
};
codec {
sound-dai = <&spdif_out>;
};
};
simple-audio-card,dai-link@2 {
format = "i2s";
cpu {
sound-dai = <&audio_controller 1>;
};
codec {
sound-dai = <&spdif_in>;
};
};
};
spdif_out: spdif-out {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
};
spdif_in: spdif-in {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dir";
};
};
&pciec {
status = "okay";
/*
* The two PCIe units are accessible through
* both standard PCIe slots and mini-PCIe
* slots on the board.
*/
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
};
pcie@2,0 {
/* Port 1, Lane 0 */
status = "okay";
};
};
&mdio {
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
phy0: ethernet-phy@0 {
reg = <0>;
};
phy1: ethernet-phy@1 {
reg = <1>;
};
};
&spi0 {
pinctrl-0 = <&spi0_pins2>;
pinctrl-names = "default";
status = "okay";
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "mx25l25635e", "jedec,spi-nor";
reg = <0>; /* Chip select 0 */
spi-max-frequency = <50000000>;
};
};
&nand_controller {
status = "okay";
nand@0 {
reg = <0>;
label = "pxa3xx_nand-0";
nand-rb = <0>;
marvell,nand-keep-config;
nand-on-flash-bbt;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "U-Boot";
reg = <0 0x800000>;
};
partition@800000 {
label = "Linux";
reg = <0x800000 0x800000>;
};
partition@1000000 {
label = "Filesystem";
reg = <0x1000000 0x3f000000>;
};
};
};
};
