Spracherkennung für: .dts vermutete Sprache: Unknown {[0] [0] [0]} [Methode: Schwerpunktbildung, einfache Gewichte, sechs Dimensionen]
// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2021 Stephan Gerhold
*/
/dts-v1/;
#include "msm8916-pm8916.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/sound/apq8016-lpass.h>
/*
* Note: The original firmware from Huawei can only boot 32-bit kernels.
* To boot this device tree using arm64 it is necessary to flash 64-bit TZ/HYP
* firmware (e.g. taken from the DragonBoard 410c).
* See
https://wiki.postmarketos.org/wiki/Huawei_Ascend_G7_(huawei-g7)
* for suggested installation instructions.
*/
/ {
model = "Huawei Ascend G7";
compatible = "huawei,g7", "qcom,msm8916";
chassis-type = "handset";
aliases {
mmc0 = &sdhc_1; /* eMMC */
mmc1 = &sdhc_2; /* SD card */
serial0 = &blsp_uart2;
};
chosen {
stdout-path = "serial0";
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&gpio_keys_default>;
label = "GPIO Buttons";
button-volume-up {
label = "Volume Up";
gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEUP>;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&gpio_leds_default>;
led-0 {
gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_RED>;
default-state = "off";
function = LED_FUNCTION_INDICATOR;
};
led-1 {
gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
default-state = "off";
function = LED_FUNCTION_INDICATOR;
};
led-2 {
gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_BLUE>;
default-state = "off";
function = LED_FUNCTION_INDICATOR;
};
};
usb_id: usb-id {
compatible = "linux,extcon-usb-gpio";
id-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb_id_default>;
};
};
&blsp_i2c2 {
status = "okay";
magnetometer@c {
compatible = "asahi-kasei,ak09911";
reg = <0x0c>;
vdd-supply = <&pm8916_l17>;
vid-supply = <&pm8916_l6>;
reset-gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&mag_reset_default>;
};
accelerometer@1e {
compatible = "kionix,kx023-1025";
reg = <0x1e>;
interrupt-parent = <&tlmm>;
interrupts = <115 IRQ_TYPE_EDGE_RISING>;
vdd-supply = <&pm8916_l17>;
vddio-supply = <&pm8916_l6>;
pinctrl-names = "default";
pinctrl-0 = <&accel_irq_default>;
mount-matrix = "-1", "0", "0",
"0", "1", "0",
"0", "0", "1";
};
proximity@39 {
compatible = "avago,apds9930";
reg = <0x39>;
interrupt-parent = <&tlmm>;
interrupts = <113 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&pm8916_l17>;
vddio-supply = <&pm8916_l6>;
led-max-microamp = <100000>;
amstaos,proximity-diodes = <1>;
pinctrl-names = "default";
pinctrl-0 = <&prox_irq_default>;
};
regulator@3e {
compatible = "ti,tps65132";
reg = <0x3e>;
pinctrl-names = "default";
pinctrl-0 = <®_lcd_en_default>;
reg_lcd_pos: outp {
regulator-name = "outp";
regulator-min-microvolt = <5400000>;
regulator-max-microvolt = <5400000>;
enable-gpios = <&tlmm 97 GPIO_ACTIVE_HIGH>;
regulator-active-discharge = <1>;
};
reg_lcd_neg: outn {
regulator-name = "outn";
regulator-min-microvolt = <5400000>;
regulator-max-microvolt = <5400000>;
enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
regulator-active-discharge = <1>;
};
};
};
&blsp_i2c5 {
status = "okay";
rmi4@70 {
compatible = "syna,rmi4-i2c";
reg = <0x70>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <&tlmm>;
interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&pm8916_l17>;
vio-supply = <&pm8916_l16>;
pinctrl-names = "default";
pinctrl-0 = <&ts_irq_default>;
syna,startup-delay-ms = <100>;
rmi4-f01@1 {
reg = <0x1>;
syna,nosleep-mode = <1>; /* Allow sleeping */
};
rmi4-f11@11 {
reg = <0x11>;
syna,sensor-type = <1>; /* Touchscreen */
};
};
};
&blsp_i2c6 {
status = "okay";
nfc@28 {
compatible = "nxp,pn547", "nxp,nxp-nci-i2c";
reg = <0x28>;
interrupt-parent = <&tlmm>;
interrupts = <21 IRQ_TYPE_EDGE_RISING>;
enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
firmware-gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&nfc_default>;
};
};
&blsp_uart2 {
status = "okay";
pinctrl-0 = <&blsp_uart2_console_default>;
pinctrl-1 = <&blsp_uart2_console_sleep>;
pinctrl-names = "default", "sleep";
};
&lpass {
status = "okay";
};
&lpass_codec {
status = "okay";
};
&pm8916_codec {
status = "okay";
qcom,micbias-lvl = <2800>;
qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
qcom,hphl-jack-type-normally-open;
};
&pm8916_l8 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
};
&pm8916_resin {
status = "okay";
linux,code = <KEY_VOLUMEDOWN>;
};
&pm8916_rpm_regulators {
pm8916_l16: l16 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8916_l17: l17 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
};
};
&pm8916_vib {
status = "okay";
};
&sdhc_1 {
status = "okay";
};
&sdhc_2 {
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
/*
* The Huawei device tree sets cd-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>.
* However, gpio38 does not change its state when inserting/removing the
* SD card, it's just low all the time. The Huawei kernel seems to use
* polling for SD card detection instead.
*
* However, looking closer at the GPIO debug output it turns out that
* gpio56 switches its state when inserting/removing the SD card.
* It behaves just like gpio38 normally does. Usually GPIO56 is used as
* "UIM2_PRESENT", i.e. to check if a second SIM card is inserted.
* Maybe Huawei decided to replace the second SIM card slot with the
* SD card slot and forgot to re-route to gpio38.
*/
cd-gpios = <&tlmm 56 GPIO_ACTIVE_LOW>;
};
&sound {
status = "okay";
model = "msm8916";
audio-routing =
"AMIC1", "MIC BIAS External1",
"AMIC2", "MIC BIAS External2",
"AMIC3", "MIC BIAS External1";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&cdc_pdm_default>;
pinctrl-1 = <&cdc_pdm_sleep>;
primary-dai-link {
link-name = "WCD";
cpu {
sound-dai = <&lpass MI2S_PRIMARY>;
};
codec {
sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>;
};
};
tertiary-dai-link {
link-name = "WCD-Capture";
cpu {
sound-dai = <&lpass MI2S_TERTIARY>;
};
codec {
sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>;
};
};
};
&usb {
status = "okay";
extcon = <&usb_id>, <&usb_id>;
};
&usb_hs_phy {
extcon = <&usb_id>;
};
&venus {
status = "okay";
};
&venus_mem {
status = "okay";
};
&wcnss {
status = "okay";
};
&wcnss_iris {
compatible = "qcom,wcn3620";
};
&wcnss_mem {
status = "okay";
};
&tlmm {
accel_irq_default: accel-irq-default-state {
pins = "gpio115";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
gpio_keys_default: gpio-keys-default-state {
pins = "gpio107";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
gpio_leds_default: gpio-leds-default-state {
pins = "gpio8", "gpio9", "gpio10";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
nfc_default: nfc-default-state {
pins = "gpio2", "gpio20", "gpio21";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
mag_reset_default: mag-reset-default-state {
pins = "gpio36";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
prox_irq_default: prox-irq-default-state {
pins = "gpio113";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
reg_lcd_en_default: reg-lcd-en-default-state {
pins = "gpio32", "gpio97";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
sdc2_cd_default: sdc2-cd-default-state {
pins = "gpio56";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
ts_irq_default: ts-irq-default-state {
pins = "gpio13";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
usb_id_default: usb-id-default-state {
pins = "gpio117";
function = "gpio";
drive-strength = <8>;
bias-pull-up;
};
};
