Quelle  pm6150.dtsi   Sprache: unbekannt

// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2019, The Linux Foundation. All rights reserved.
 */

#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
#include <dt-bindings/thermal/thermal.h>

/ {
 thermal-zones {
  pm6150_thermal: pm6150-thermal {
   polling-delay-passive = <100>;

   thermal-sensors = <&pm6150_temp>;

   trips {
    pm6150_trip0: trip0 {
     temperature = <95000>;
     hysteresis = <0>;
     type = "passive";
    };

    pm6150_crit: crit {
     temperature = <115000>;
     hysteresis = <0>;
     type = "critical";
    };
   };
  };
 };
};

&spmi_bus {
 pm6150_lsid0: pmic@0 {
  compatible = "qcom,pm6150", "qcom,spmi-pmic";
  reg = <0x0 SPMI_USID>;
  #address-cells = <1>;
  #size-cells = <0>;

  pm6150_pon: pon@800 {
   compatible = "qcom,pm8998-pon";
   reg = <0x800>;
   mode-bootloader = <0x2>;
   mode-recovery = <0x1>;

   pm6150_pwrkey: pwrkey {
    compatible = "qcom,pm8941-pwrkey";
    interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
    debounce = <15625>;
    bias-pull-up;
    linux,code = <KEY_POWER>;
   };

   pm6150_resin: resin {
    compatible = "qcom,pm8941-resin";
    interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
    debounce = <15625>;
    bias-pull-up;
    status = "disabled";
   };
  };

  pm6150_vbus: usb-vbus-regulator@1100 {
   compatible = "qcom,pm6150-vbus-reg",
         "qcom,pm8150b-vbus-reg";
   reg = <0x1100>;
   status = "disabled";
  };

  pm6150_typec: typec@1500 {
   compatible = "qcom,pm6150-typec",
         "qcom,pm8150b-typec";
   reg = <0x1500>, <0x1700>;
   interrupts = <0x0 0x15 0x00 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x15 0x01 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x15 0x02 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x15 0x03 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x15 0x04 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x15 0x05 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x15 0x06 IRQ_TYPE_EDGE_BOTH>,
         <0x0 0x15 0x07 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x17 0x00 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x17 0x01 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x17 0x02 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x17 0x03 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x17 0x04 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x17 0x05 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x17 0x06 IRQ_TYPE_EDGE_RISING>,
         <0x0 0x17 0x07 IRQ_TYPE_EDGE_RISING>;
   interrupt-names = "or-rid-detect-change",
       "vpd-detect",
       "cc-state-change",
       "vconn-oc",
       "vbus-change",
       "attach-detach",
       "legacy-cable-detect",
       "try-snk-src-detect",
       "sig-tx",
       "sig-rx",
       "msg-tx",
       "msg-rx",
       "msg-tx-failed",
       "msg-tx-discarded",
       "msg-rx-discarded",
       "fr-swap";
   status = "disabled";
  };

  pm6150_temp: temp-alarm@2400 {
   compatible = "qcom,spmi-temp-alarm";
   reg = <0x2400>;
   interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
   io-channels = <&pm6150_adc ADC5_DIE_TEMP>;
   io-channel-names = "thermal";
   #thermal-sensor-cells = <0>;
  };

  pm6150_adc: adc@3100 {
   compatible = "qcom,spmi-adc5";
   reg = <0x3100>;
   interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
   #address-cells = <1>;
   #size-cells = <0>;
   #io-channel-cells = <1>;

   channel@6 {
    reg = <ADC5_DIE_TEMP>;
    label = "die_temp";
   };
  };

  pm6150_adc_tm: adc-tm@3500 {
   compatible = "qcom,spmi-adc-tm5";
   reg = <0x3500>;
   interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
   #thermal-sensor-cells = <1>;
   #address-cells = <1>;
   #size-cells = <0>;
   status = "disabled";
  };

  pm6150_rtc: rtc@6000 {
   compatible = "qcom,pm8941-rtc";
   reg = <0x6000>, <0x6100>;
   reg-names = "rtc", "alarm";
   interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
   status = "disabled";
  };

  pm6150_gpios: gpio@c000 {
   compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
   reg = <0xc000>;
   gpio-controller;
   gpio-ranges = <&pm6150_gpios 0 0 10>;
   #gpio-cells = <2>;
   interrupt-controller;
   #interrupt-cells = <2>;
  };
 };

 pm6150_lsid1: pmic@1 {
  compatible = "qcom,pm6150", "qcom,spmi-pmic";
  reg = <0x1 SPMI_USID>;
  #address-cells = <1>;
  #size-cells = <0>;

  pm6150_vib: vibrator@5300 {
   compatible = "qcom,pm6150-vib", "qcom,pmi632-vib";
   reg = <0x5300>;
   status = "disabled";
  };
 };
};