Quelle  sc7180-trogdor-lazor.dtsi   Sprache: unbekannt

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Google Lazor board device tree source
 *
 * Copyright 2020 Google LLC.
 */

#include "sc7180-trogdor-clamshell.dtsi"

&ap_sar_sensor {
 semtech,cs0-ground;
 semtech,combined-sensors = <3>;
 semtech,resolution = "fine";
 semtech,startup-sensor = <0>;
 semtech,proxraw-strength = <8>;
 semtech,avg-pos-strength = <64>;
};

&ap_tp_i2c {
 status = "okay";
};

/*
 * Lazor is stuffed with a 47k NTC as charger thermistor which currently is
 * not supported by the PM6150 ADC driver. Disable the charger thermal zone
 * to avoid using bogus temperature values.
 */
&charger_thermal {
 status = "disabled";
};

ap_ts_pen_1v8: &i2c4 {
 status = "okay";
 clock-frequency = <400000>;

 ap_ts: touchscreen@10 {
  compatible = "hid-over-i2c";
  reg = <0x10>;
  pinctrl-names = "default";
  pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;

  interrupt-parent = <&tlmm>;
  interrupts = <9 IRQ_TYPE_LEVEL_LOW>;

  panel = <&panel>;
  post-power-on-delay-ms = <20>;
  hid-descr-addr = <0x0001>;

  vdd-supply = <&pp3300_ts>;
 };
};

&panel {
 compatible = "boe,nv133fhm-n62";
};

&pm6150_adc {
 /delete-node/ channel@4f;
};

&pm6150_adc_tm {
 status = "disabled";

 /delete-node/ charger-thermistor@0;
};

&trackpad {
 interrupts = <58 IRQ_TYPE_EDGE_FALLING>;
};

&wifi {
 qcom,calibration-variant = "GO_LAZOR";
};

/* PINCTRL - modifications to sc7180-trogdor.dtsi */

&trackpad_int_1v8_odl {
 pins = "gpio58";
};

&ts_reset_l {
 /* This pin is not connected on -rev0, pull up to park. */
 /delete-property/bias-disable;
 bias-pull-up;
};

/* PINCTRL - board-specific pinctrl */

&tlmm {
 gpio-line-names = "ESIM_MISO",
     "ESIM_MOSI",
     "ESIM_CLK",
     "ESIM_CS_L",
     "",
     "",
     "AP_TP_I2C_SDA",
     "AP_TP_I2C_SCL",
     "TS_RESET_L",
     "TS_INT_L",
     "",
     "EDP_BRIJ_IRQ",
     "AP_EDP_BKLTEN",
     "AP_RAM_ID2",
     "",
     "EDP_BRIJ_I2C_SDA",
     "EDP_BRIJ_I2C_SCL",
     "HUB_RST_L",
     "",
     "AP_RAM_ID1",
     "AP_SKU_ID2",
     "",
     "",
     "AMP_EN",
     "P_SENSOR_INT_L",
     "AP_SAR_SENSOR_SDA",
     "AP_SAR_SENSOR_SCL",
     "",
     "HP_IRQ",
     "AP_RAM_ID0",
     "EN_PP3300_DX_EDP",
     "AP_BRD_ID2",
     "BRIJ_SUSPEND",
     "AP_BRD_ID0",
     "AP_H1_SPI_MISO",
     "AP_H1_SPI_MOSI",
     "AP_H1_SPI_CLK",
     "AP_H1_SPI_CS_L",
     "",
     "",
     "",
     "",
     "H1_AP_INT_ODL",
     "",
     "UART_AP_TX_DBG_RX",
     "UART_DBG_TX_AP_RX",
     "HP_I2C_SDA",
     "HP_I2C_SCL",
     "FORCED_USB_BOOT",
     "",
     "",
     "AMP_DIN",
     "",
     "HP_BCLK",
     "HP_LRCLK",
     "HP_DOUT",
     "HP_DIN",
     "HP_MCLK",
     "TRACKPAD_INT_1V8_ODL",
     "AP_EC_SPI_MISO",
     "AP_EC_SPI_MOSI",
     "AP_EC_SPI_CLK",
     "AP_EC_SPI_CS_L",
     "AP_SPI_CLK",
     "AP_SPI_MOSI",
     "AP_SPI_MISO",
     /*
      * AP_FLASH_WP_L is crossystem ABI. Schematics
      * call it BIOS_FLASH_WP_L.
      */
     "AP_FLASH_WP_L",
     "DBG_SPI_HOLD_L",
     "AP_SPI_CS0_L",
     "",
     "",
     "",
     "",
     "",
     "",
     "UIM2_DATA",
     "UIM2_CLK",
     "UIM2_RST",
     "UIM2_PRESENT",
     "UIM1_DATA",
     "UIM1_CLK",
     "UIM1_RST",
     "",
     "EN_PP3300_CODEC",
     "EN_PP3300_HUB",
     "",
     "",
     "",
     "",
     "",
     "AP_SKU_ID1",
     "AP_RST_REQ",
     "",
     "AP_BRD_ID1",
     "AP_EC_INT_L",
     "",
     "",
     "",
     "",
     "",
     "",
     "",
     "",
     "",
     "EDP_BRIJ_EN",
     "AP_SKU_ID0",
     "",
     "",
     "",
     "",
     "",
     "",
     "",
     "",
     "",
     "AP_TS_PEN_I2C_SDA",
     "AP_TS_PEN_I2C_SCL",
     "DP_HOT_PLUG_DET",
     "EC_IN_RW_ODL";
};