Quelle  sm8550-hdk.dts   Sprache: unbekannt

// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2024 Linaro Limited
 */

/dts-v1/;

#include <dt-bindings/leds/common.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sm8550.dtsi"
#include "pm8010.dtsi"
#include "pm8550.dtsi"
#include "pm8550b.dtsi"
#define PMK8550VE_SID 5
#include "pm8550ve.dtsi"
#include "pm8550vs.dtsi"
#include "pmk8550.dtsi"
#include "pmr735d_a.dtsi"

/ {
 model = "Qualcomm Technologies, Inc. SM8550 HDK";
 compatible = "qcom,sm8550-hdk", "qcom,sm8550";
 chassis-type = "embedded";

 aliases {
  serial0 = &uart7;
  serial1 = &uart14;
 };

 wcd938x: audio-codec {
  compatible = "qcom,wcd9385-codec";

  pinctrl-names = "default";
  pinctrl-0 = <&wcd_default>;

  qcom,micbias1-microvolt = <1800000>;
  qcom,micbias2-microvolt = <1800000>;
  qcom,micbias3-microvolt = <1800000>;
  qcom,micbias4-microvolt = <1800000>;
  qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
  qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
  qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
  qcom,rx-device = <&wcd_rx>;
  qcom,tx-device = <&wcd_tx>;

  reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;

  vdd-buck-supply = <&vreg_l15b_1p8>;
  vdd-rxtx-supply = <&vreg_l15b_1p8>;
  vdd-io-supply = <&vreg_l15b_1p8>;
  vdd-mic-bias-supply = <&vreg_bob1>;

  #sound-dai-cells = <1>;
 };

 chosen {
  stdout-path = "serial0:115200n8";
 };

 hdmi-out {
  compatible = "hdmi-connector";
  type = "a";

  port {
   hdmi_connector_out: endpoint {
    remote-endpoint = <<9611_out>;
   };
  };
 };

 gpio-keys {
  compatible = "gpio-keys";

  pinctrl-0 = <&volume_up_n>;
  pinctrl-names = "default";

  key-volume-up {
   label = "Volume Up";
   linux,code = <KEY_VOLUMEUP>;
   gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
   debounce-interval = <15>;
   linux,can-disable;
   wakeup-source;
  };
 };

 leds {
  compatible = "gpio-leds";

  led-0 {
   function = LED_FUNCTION_BLUETOOTH;
   color = <LED_COLOR_ID_BLUE>;
   gpios = <&tlmm 159 GPIO_ACTIVE_HIGH>;
   linux,default-trigger = "bluetooth-power";
   default-state = "off";
  };

  led-1 {
   function = LED_FUNCTION_INDICATOR;
   color = <LED_COLOR_ID_GREEN>;
   gpios = <&tlmm 160 GPIO_ACTIVE_HIGH>;
   default-state = "off";
   panic-indicator;
  };

  led-2 {
   function = LED_FUNCTION_WLAN;
   color = <LED_COLOR_ID_ORANGE>;
   gpios = <&tlmm 162 GPIO_ACTIVE_HIGH>;
   linux,default-trigger = "phy0tx";
   default-state = "off";
  };
 };

 pmic-glink {
  compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
  #address-cells = <1>;
  #size-cells = <0>;
  orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;

  connector@0 {
   compatible = "usb-c-connector";
   reg = <0>;
   power-role = "dual";
   data-role = "dual";

   ports {
    #address-cells = <1>;
    #size-cells = <0>;

    port@0 {
     reg = <0>;

     pmic_glink_hs_in: endpoint {
      remote-endpoint = <&usb_1_dwc3_hs>;
     };
    };

    port@1 {
     reg = <1>;

     pmic_glink_ss_in: endpoint {
      remote-endpoint = <&usb_dp_qmpphy_out>;
     };
    };

    port@2 {
     reg = <2>;

     pmic_glink_sbu: endpoint {
      remote-endpoint = <&fsa4480_sbu_mux>;
     };
    };
   };
  };
 };

 lt9611_1v2: regulator-lt9611-1v2 {
  compatible = "regulator-fixed";

  regulator-name = "LT9611_1V2";
  regulator-min-microvolt = <1200000>;
  regulator-max-microvolt = <1200000>;

  vin-supply = <&vph_pwr>;
  gpio = <&tlmm 152 GPIO_ACTIVE_HIGH>;

  enable-active-high;
 };

 lt9611_3v3: regulator-lt9611-3v3 {
  compatible = "regulator-fixed";

  regulator-name = "LT9611_3V3";
  regulator-min-microvolt = <3300000>;
  regulator-max-microvolt = <3300000>;

  vin-supply = <&vreg_bob_3v3>;
  gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;

  enable-active-high;
 };

 vph_pwr: regulator-vph-pwr {
  compatible = "regulator-fixed";

  regulator-name = "vph_pwr";
  regulator-min-microvolt = <3700000>;
  regulator-max-microvolt = <3700000>;
  regulator-always-on;
  regulator-boot-on;
 };

 vreg_bob_3v3: regulator-vreg-bob-3v3 {
  compatible = "regulator-fixed";

  regulator-name = "VREG_BOB_3P3";
  regulator-min-microvolt = <3300000>;
  regulator-max-microvolt = <3300000>;

  vin-supply = <&vph_pwr>;
 };

 sound {
  compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
  model = "SM8550-HDK";
  audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
    "SpkrRight IN", "WSA_SPK2 OUT",
    "IN1_HPHL", "HPHL_OUT",
    "IN2_HPHR", "HPHR_OUT",
    "AMIC1", "MIC BIAS1",
    "AMIC2", "MIC BIAS2",
    "AMIC5", "MIC BIAS4",
    "TX SWR_INPUT0", "ADC1_OUTPUT",
    "TX SWR_INPUT1", "ADC2_OUTPUT",
    "TX SWR_INPUT1", "ADC4_OUTPUT";

  wcd-playback-dai-link {
   link-name = "WCD Playback";

   cpu {
    sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
   };

   codec {
    sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
   };

   platform {
    sound-dai = <&q6apm>;
   };
  };

  wcd-capture-dai-link {
   link-name = "WCD Capture";

   cpu {
    sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
   };

   codec {
    sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>;
   };

   platform {
    sound-dai = <&q6apm>;
   };
  };

  wsa-dai-link {
   link-name = "WSA Playback";

   cpu {
    sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
   };

   codec {
    sound-dai = <&north_spkr>, <&south_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
   };

   platform {
    sound-dai = <&q6apm>;
   };
  };

  va-dai-link {
   link-name = "VA Capture";

   cpu {
    sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
   };

   codec {
    sound-dai = <&lpass_vamacro 0>;
   };

   platform {
    sound-dai = <&q6apm>;
   };
  };
 };

 wcn7850-pmu {
  compatible = "qcom,wcn7850-pmu";

  pinctrl-names = "default";
  pinctrl-0 = <&wlan_en>, <&bt_default>, <&pmk8550_sleep_clk>;

  wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
  bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;

  vdd-supply = <&vreg_s5g_0p85>;
  vddio-supply = <&vreg_l15b_1p8>;
  vddaon-supply = <&vreg_s2g_0p85>;
  vdddig-supply = <&vreg_s4e_0p95>;
  vddrfa1p2-supply = <&vreg_s4g_1p25>;
  vddrfa1p8-supply = <&vreg_s6g_1p86>;

  regulators {
   vreg_pmu_rfa_cmn: ldo0 {
    regulator-name = "vreg_pmu_rfa_cmn";
   };

   vreg_pmu_aon_0p59: ldo1 {
    regulator-name = "vreg_pmu_aon_0p59";
   };

   vreg_pmu_wlcx_0p8: ldo2 {
    regulator-name = "vreg_pmu_wlcx_0p8";
   };

   vreg_pmu_wlmx_0p85: ldo3 {
    regulator-name = "vreg_pmu_wlmx_0p85";
   };

   vreg_pmu_btcmx_0p85: ldo4 {
    regulator-name = "vreg_pmu_btcmx_0p85";
   };

   vreg_pmu_rfa_0p8: ldo5 {
    regulator-name = "vreg_pmu_rfa_0p8";
   };

   vreg_pmu_rfa_1p2: ldo6 {
    regulator-name = "vreg_pmu_rfa_1p2";
   };

   vreg_pmu_rfa_1p8: ldo7 {
    regulator-name = "vreg_pmu_rfa_1p8";
   };

   vreg_pmu_pcie_0p9: ldo8 {
    regulator-name = "vreg_pmu_pcie_0p9";
   };

   vreg_pmu_pcie_1p8: ldo9 {
    regulator-name = "vreg_pmu_pcie_1p8";
   };
  };
 };
};

&apps_rsc {
 regulators-0 {
  compatible = "qcom,pm8550-rpmh-regulators";

  vdd-bob1-supply = <&vph_pwr>;
  vdd-bob2-supply = <&vph_pwr>;
  vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
  vdd-l2-l13-l14-supply = <&vreg_bob1>;
  vdd-l3-supply = <&vreg_s4g_1p25>;
  vdd-l5-l16-supply = <&vreg_bob1>;
  vdd-l6-l7-supply = <&vreg_bob1>;
  vdd-l8-l9-supply = <&vreg_bob1>;
  vdd-l11-supply = <&vreg_s4g_1p25>;
  vdd-l12-supply = <&vreg_s6g_1p86>;
  vdd-l15-supply = <&vreg_s6g_1p86>;
  vdd-l17-supply = <&vreg_bob2>;

  qcom,pmic-id = "b";

  vreg_bob1: bob1 {
   regulator-name = "vreg_bob1";
   regulator-min-microvolt = <3296000>;
   regulator-max-microvolt = <3960000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_bob2: bob2 {
   regulator-name = "vreg_bob2";
   regulator-min-microvolt = <2720000>;
   regulator-max-microvolt = <3960000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l1b_1p8: ldo1 {
   regulator-name = "vreg_l1b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2b_3p0: ldo2 {
   regulator-name = "vreg_l2b_3p0";
   regulator-min-microvolt = <3008000>;
   regulator-max-microvolt = <3008000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l5b_3p1: ldo5 {
   regulator-name = "vreg_l5b_3p1";
   regulator-min-microvolt = <3104000>;
   regulator-max-microvolt = <3104000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l6b_1p8: ldo6 {
   regulator-name = "vreg_l6b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <3008000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l7b_1p8: ldo7 {
   regulator-name = "vreg_l7b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <3008000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l8b_1p8: ldo8 {
   regulator-name = "vreg_l8b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <3008000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l9b_2p9: ldo9 {
   regulator-name = "vreg_l9b_2p9";
   regulator-min-microvolt = <2960000>;
   regulator-max-microvolt = <3008000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l11b_1p2: ldo11 {
   regulator-name = "vreg_l11b_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1504000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l12b_1p8: ldo12 {
   regulator-name = "vreg_l12b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l13b_3p0: ldo13 {
   regulator-name = "vreg_l13b_3p0";
   regulator-min-microvolt = <3000000>;
   regulator-max-microvolt = <3000000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l14b_3p2: ldo14 {
   regulator-name = "vreg_l14b_3p2";
   regulator-min-microvolt = <3200000>;
   regulator-max-microvolt = <3200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l15b_1p8: ldo15 {
   regulator-name = "vreg_l15b_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l16b_2p8: ldo16 {
   regulator-name = "vreg_l16b_2p8";
   regulator-min-microvolt = <2800000>;
   regulator-max-microvolt = <2800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l17b_2p5: ldo17 {
   regulator-name = "vreg_l17b_2p5";
   regulator-min-microvolt = <2504000>;
   regulator-max-microvolt = <2504000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-1 {
  compatible = "qcom,pm8550vs-rpmh-regulators";

  vdd-l1-supply = <&vreg_s4g_1p25>;
  vdd-l2-supply = <&vreg_s4e_0p95>;
  vdd-l3-supply = <&vreg_s4e_0p95>;

  qcom,pmic-id = "c";

  vreg_l3c_0p9: ldo3 {
   regulator-name = "vreg_l3c_0p9";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <912000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-2 {
  compatible = "qcom,pm8550vs-rpmh-regulators";

  vdd-l1-supply = <&vreg_s4e_0p95>;
  vdd-l2-supply = <&vreg_s4e_0p95>;
  vdd-l3-supply = <&vreg_s4e_0p95>;

  qcom,pmic-id = "d";

  vreg_l1d_0p88: ldo1 {
   regulator-name = "vreg_l1d_0p88";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <920000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  /* ldo2 supplies SM8550 VDD_LPI_MX */
 };

 regulators-3 {
  compatible = "qcom,pm8550vs-rpmh-regulators";

  vdd-l1-supply = <&vreg_s4e_0p95>;
  vdd-l2-supply = <&vreg_s4e_0p95>;
  vdd-l3-supply = <&vreg_s4g_1p25>;
  vdd-s4-supply = <&vph_pwr>;
  vdd-s5-supply = <&vph_pwr>;

  qcom,pmic-id = "e";

  vreg_s4e_0p95: smps4 {
   regulator-name = "vreg_s4e_0p95";
   regulator-min-microvolt = <904000>;
   regulator-max-microvolt = <984000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s5e_1p08: smps5 {
   regulator-name = "vreg_s5e_1p08";
   regulator-min-microvolt = <1080000>;
   regulator-max-microvolt = <1120000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l1e_0p88: ldo1 {
   regulator-name = "vreg_l1e_0p88";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <880000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2e_0p9: ldo2 {
   regulator-name = "vreg_l2e_0p9";
   regulator-min-microvolt = <904000>;
   regulator-max-microvolt = <970000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3e_1p2: ldo3 {
   regulator-name = "vreg_l3e_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-4 {
  compatible = "qcom,pm8550ve-rpmh-regulators";

  vdd-l1-supply = <&vreg_s4e_0p95>;
  vdd-l2-supply = <&vreg_s4e_0p95>;
  vdd-l3-supply = <&vreg_s4e_0p95>;
  vdd-s4-supply = <&vph_pwr>;

  qcom,pmic-id = "f";

  vreg_s4f_0p5: smps4 {
   regulator-name = "vreg_s4f_0p5";
   regulator-min-microvolt = <500000>;
   regulator-max-microvolt = <700000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l1f_0p9: ldo1 {
   regulator-name = "vreg_l1f_0p9";
   regulator-min-microvolt = <912000>;
   regulator-max-microvolt = <912000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2f_0p88: ldo2 {
   regulator-name = "vreg_l2f_0p88";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <912000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3f_0p88: ldo3 {
   regulator-name = "vreg_l3f_0p88";
   regulator-min-microvolt = <880000>;
   regulator-max-microvolt = <912000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-5 {
  compatible = "qcom,pm8550vs-rpmh-regulators";

  vdd-l1-supply = <&vreg_s4g_1p25>;
  vdd-l2-supply = <&vreg_s4g_1p25>;
  vdd-l3-supply = <&vreg_s4g_1p25>;
  vdd-s1-supply = <&vph_pwr>;
  vdd-s2-supply = <&vph_pwr>;
  vdd-s3-supply = <&vph_pwr>;
  vdd-s4-supply = <&vph_pwr>;
  vdd-s5-supply = <&vph_pwr>;
  vdd-s6-supply = <&vph_pwr>;

  qcom,pmic-id = "g";

  vreg_s1g_1p25: smps1 {
   regulator-name = "vreg_s1g_1p25";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1300000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s2g_0p85: smps2 {
   regulator-name = "vreg_s2g_0p85";
   regulator-min-microvolt = <800000>;
   regulator-max-microvolt = <1000000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s3g_0p8: smps3 {
   regulator-name = "vreg_s3g_0p8";
   regulator-min-microvolt = <300000>;
   regulator-max-microvolt = <1004000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s4g_1p25: smps4 {
   regulator-name = "vreg_s4g_1p25";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1352000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s5g_0p85: smps5 {
   regulator-name = "vreg_s5g_0p85";
   regulator-min-microvolt = <500000>;
   regulator-max-microvolt = <1004000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s6g_1p86: smps6 {
   regulator-name = "vreg_s6g_1p86";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <2000000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l1g_1p2: ldo1 {
   regulator-name = "vreg_l1g_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3g_1p2: ldo3 {
   regulator-name = "vreg_l3g_1p2";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-6 {
  compatible = "qcom,pm8010-rpmh-regulators";

  vdd-l1-l2-supply = <&vreg_s4g_1p25>;
  vdd-l3-l4-supply = <&vreg_bob2>;
  vdd-l5-supply = <&vreg_s6g_1p86>;
  vdd-l6-supply = <&vreg_s6g_1p86>;
  vdd-l7-supply = <&vreg_bob1>;

  qcom,pmic-id = "m";

  vreg_l1m_1p056: ldo1 {
   regulator-name = "vreg_l1m_1p056";
   regulator-min-microvolt = <1056000>;
   regulator-max-microvolt = <1056000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2m_1p056: ldo2 {
   regulator-name = "vreg_l2m_1p056";
   regulator-min-microvolt = <1056000>;
   regulator-max-microvolt = <1056000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3m_2p8: ldo3 {
   regulator-name = "vreg_l3m_2p8";
   regulator-min-microvolt = <2800000>;
   regulator-max-microvolt = <2800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l4m_2p8: ldo4 {
   regulator-name = "vreg_l4m_2p8";
   regulator-min-microvolt = <2800000>;
   regulator-max-microvolt = <2800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l5m_1p8: ldo5 {
   regulator-name = "vreg_l5m_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l6m_1p8: ldo6 {
   regulator-name = "vreg_l6m_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l7m_2p9: ldo7 {
   regulator-name = "vreg_l7m_2p9";
   regulator-min-microvolt = <2800000>;
   regulator-max-microvolt = <2904000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-7 {
  compatible = "qcom,pm8010-rpmh-regulators";

  vdd-l1-l2-supply = <&vreg_s4g_1p25>;
  vdd-l3-l4-supply = <&vreg_bob2>;
  vdd-l5-supply = <&vreg_s6g_1p86>;
  vdd-l6-supply = <&vreg_bob1>;
  vdd-l7-supply = <&vreg_bob1>;

  qcom,pmic-id = "n";

  vreg_l1n_1p1: ldo1 {
   regulator-name = "vreg_l1n_1p1";
   regulator-min-microvolt = <1104000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2n_1p1: ldo2 {
   regulator-name = "vreg_l2n_1p1";
   regulator-min-microvolt = <1104000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3n_2p8: ldo3 {
   regulator-name = "vreg_l3n_2p8";
   regulator-min-microvolt = <2800000>;
   regulator-max-microvolt = <3000000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l4n_2p8: ldo4 {
   regulator-name = "vreg_l4n_2p8";
   regulator-min-microvolt = <2800000>;
   regulator-max-microvolt = <3300000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l5n_1p8: ldo5 {
   regulator-name = "vreg_l5n_1p8";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1800000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l6n_3p3: ldo6 {
   regulator-name = "vreg_l6n_3p3";
   regulator-min-microvolt = <2800000>;
   regulator-max-microvolt = <3304000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l7n_2p96: ldo7 {
   regulator-name = "vreg_l7n_2p96";
   regulator-min-microvolt = <2800000>;
   regulator-max-microvolt = <2960000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };
 };
};

&i2c0 {
 clock-frequency = <400000>;
 status = "okay";

 lt9611_codec: hdmi-bridge@2b {
  compatible = "lontium,lt9611uxc";
  reg = <0x2b>;

  interrupts-extended = <&tlmm 8 IRQ_TYPE_EDGE_FALLING>;

  reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;

  vdd-supply = <<9611_1v2>;
  vcc-supply = <<9611_3v3>;

  pinctrl-0 = <<9611_irq_pin>, <<9611_rst_pin>;
  pinctrl-names = "default";

  ports {
   #address-cells = <1>;
   #size-cells = <0>;

   port@0 {
    reg = <0>;

    lt9611_a: endpoint {
     remote-endpoint = <&mdss_dsi0_out>;
    };
   };

   port@2 {
    reg = <2>;

    lt9611_out: endpoint {
     remote-endpoint = <&hdmi_connector_out>;
    };
   };
  };
 };
};

&i2c_hub_2 {
 status = "okay";

 typec-mux@42 {
  compatible = "fcs,fsa4480";
  reg = <0x42>;

  vcc-supply = <&vreg_bob1>;

  mode-switch;
  orientation-switch;

  port {
   fsa4480_sbu_mux: endpoint {
    remote-endpoint = <&pmic_glink_sbu>;
   };
  };
 };
};

&i2c_master_hub_0 {
 status = "okay";
};

&ipa {
 qcom,gsi-loader = "self";
 memory-region = <&ipa_fw_mem>;
 firmware-name = "qcom/sm8550/ipa_fws.mbn";
 status = "okay";
};

&iris {
 status = "okay";
};

&gpi_dma1 {
 status = "okay";
};

&gpu {
 status = "okay";

 zap-shader {
  firmware-name = "qcom/sm8550/a740_zap.mbn";
 };
};

&lpass_tlmm {
 spkr_1_sd_n_active: spkr-1-sd-n-active-state {
  pins = "gpio17";
  function = "gpio";
  drive-strength = <16>;
  bias-disable;
  output-low;
 };

 spkr_2_sd_n_active: spkr-2-sd-n-active-state {
  pins = "gpio18";
  function = "gpio";
  drive-strength = <16>;
  bias-disable;
  output-low;
 };
};

&mdss {
 status = "okay";
};

&mdss_dsi0 {
 vdda-supply = <&vreg_l3e_1p2>;
 status = "okay";
};

&mdss_dsi0_out {
 remote-endpoint = <<9611_a>;
 data-lanes = <0 1 2 3>;
};

&mdss_dsi0_phy {
 vdds-supply = <&vreg_l1e_0p88>;
 status = "okay";
};

&mdss_dp0 {
 status = "okay";
};

&mdss_dp0_out {
 data-lanes = <0 1>;
};

&pcie0 {
 wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;

 pinctrl-0 = <&pcie0_default_state>;
 pinctrl-names = "default";

 status = "okay";
};

&pcieport0 {
 wifi@0 {
  compatible = "pci17cb,1107";
  reg = <0x10000 0x0 0x0 0x0 0x0>;

  vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
  vddaon-supply = <&vreg_pmu_aon_0p59>;
  vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
  vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
  vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
  vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
  vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
  vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
  vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
 };
};

&pcie0_phy {
 vdda-phy-supply = <&vreg_l1e_0p88>;
 vdda-pll-supply = <&vreg_l3e_1p2>;

 status = "okay";
};

&pcie1 {
 wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
 perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;

 pinctrl-0 = <&pcie1_default_state>;
 pinctrl-names = "default";

 status = "okay";
};

&pcie1_phy {
 vdda-phy-supply = <&vreg_l3c_0p9>;
 vdda-pll-supply = <&vreg_l3e_1p2>;
 vdda-qref-supply = <&vreg_l1e_0p88>;

 status = "okay";
};

&pm8550_gpios {
 sdc2_card_det_n: sdc2-card-det-state {
  pins = "gpio12";
  function = "normal";
  input-enable;
  output-disable;
  bias-pull-up;
  power-source = <1>; /* 1.8 V */
 };

 volume_up_n: volume-up-n-state {
  pins = "gpio6";
  function = "normal";
  power-source = <1>;
  bias-pull-up;
  input-enable;
 };
};

/* The RGB signals are routed to 3 separate LEDs on the HDK8550 */
&pm8550_pwm {
 #address-cells = <1>;
 #size-cells = <0>;

 status = "okay";

 led@1 {
  reg = <1>;
  function = LED_FUNCTION_STATUS;
  color = <LED_COLOR_ID_RED>;
  default-state = "off";
 };

 led@2 {
  reg = <2>;
  function = LED_FUNCTION_STATUS;
  color = <LED_COLOR_ID_GREEN>;
  default-state = "off";
 };

 led@3 {
  reg = <3>;
  function = LED_FUNCTION_STATUS;
  color = <LED_COLOR_ID_BLUE>;
  default-state = "off";
 };
};

&pm8550b_eusb2_repeater {
 vdd18-supply = <&vreg_l15b_1p8>;
 vdd3-supply = <&vreg_l5b_3p1>;
};

&pon_pwrkey {
 status = "okay";
};

&pon_resin {
 linux,code = <KEY_VOLUMEDOWN>;

 status = "okay";
};

&pmk8550_gpios {
 pmk8550_sleep_clk: sleep-clk-state {
  pins = "gpio3";
  function = "func1";
  input-disable;
  output-enable;
  bias-disable;
  power-source = <0>;
 };
};

&qupv3_id_0 {
 status = "okay";
};

&qupv3_id_1 {
 status = "okay";
};

&remoteproc_adsp {
 firmware-name = "qcom/sm8550/adsp.mbn",
   "qcom/sm8550/adsp_dtb.mbn";
 status = "okay";
};

&remoteproc_cdsp {
 firmware-name = "qcom/sm8550/cdsp.mbn",
   "qcom/sm8550/cdsp_dtb.mbn";
 status = "okay";
};

&remoteproc_mpss {
 firmware-name = "qcom/sm8550/modem.mbn",
   "qcom/sm8550/modem_dtb.mbn";
 status = "okay";
};

&sdhc_2 {
 cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>;

 pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>;
 pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>;
 pinctrl-names = "default", "sleep";

 vmmc-supply = <&vreg_l9b_2p9>;
 vqmmc-supply = <&vreg_l8b_1p8>;

 bus-width = <4>;
 no-sdio;
 no-mmc;

 status = "okay";
};

&sleep_clk {
 clock-frequency = <32764>;
};

&swr0 {
 status = "okay";

 /* WSA8845, Speaker North */
 north_spkr: speaker@0,0 {
  compatible = "sdw20217020400";
  reg = <0 0>;

  pinctrl-0 = <&spkr_1_sd_n_active>;
  pinctrl-names = "default";

  powerdown-gpios = <&lpass_tlmm 17 GPIO_ACTIVE_LOW>;

  vdd-1p8-supply = <&vreg_l15b_1p8>;
  vdd-io-supply = <&vreg_l15b_1p8>;

  #sound-dai-cells = <0>;
  sound-name-prefix = "SpkrLeft";
  qcom,port-mapping = <1 2 3 7 10 13>;
 };

 /* WSA8845, Speaker South */
 south_spkr: speaker@0,1 {
  compatible = "sdw20217020400";
  reg = <0 1>;

  pinctrl-0 = <&spkr_2_sd_n_active>;
  pinctrl-names = "default";

  powerdown-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_LOW>;

  vdd-1p8-supply = <&vreg_l15b_1p8>;
  vdd-io-supply = <&vreg_l15b_1p8>;

  #sound-dai-cells = <0>;
  sound-name-prefix = "SpkrRight";
  qcom,port-mapping = <4 5 6 7 11 13>;
 };
};

&swr1 {
 status = "okay";

 /* WCD9385 RX */
 wcd_rx: codec@0,4 {
  compatible = "sdw20217010d00";
  reg = <0 4>;

  /*
   * WCD9385 RX Port 1 (HPH_L/R)      <=> SWR1 Port 1 (HPH_L/R)
   * WCD9385 RX Port 2 (CLSH)         <=> SWR1 Port 2 (CLSH)
   * WCD9385 RX Port 3 (COMP_L/R)     <=> SWR1 Port 3 (COMP_L/R)
   * WCD9385 RX Port 4 (LO)           <=> SWR1 Port 4 (LO)
   * WCD9385 RX Port 5 (DSD_L/R)      <=> SWR1 Port 5 (DSD_L/R)
   */
  qcom,rx-port-mapping = <1 2 3 4 5>;
 };
};

&swr2 {
 status = "okay";

 /* WCD9385 TX */
 wcd_tx: codec@0,3 {
  compatible = "sdw20217010d00";
  reg = <0 3>;

  /*
   * WCD9385 TX Port 1 (ADC1,2)             <=> SWR2 Port 2 (TX SWR_INPUT 0,1,2,3)
   * WCD9385 TX Port 2 (ADC3,4)             <=> SWR2 Port 2 (TX SWR_INPUT 0,1,2,3)
   * WCD9385 TX Port 3 (DMIC0,1,2,3 & MBHC) <=> SWR2 Port 3 (TX SWR_INPUT 4,5,6,7)
   * WCD9385 TX Port 4 (DMIC4,5,6,7)        <=> SWR2 Port 4 (TX SWR_INPUT 8,9,10,11)
   */
  qcom,tx-port-mapping = <2 2 3 4>;
 };
};

&tlmm {
 /* Reserved I/Os for NFC */
 gpio-reserved-ranges = <32 8>;

 bt_default: bt-default-state {
  bt-en-pins {
   pins = "gpio81";
   function = "gpio";
   drive-strength = <16>;
   bias-disable;
  };

  sw-ctrl-pins {
   pins = "gpio82";
   function = "gpio";
   bias-pull-down;
  };
 };

 lt9611_irq_pin: lt9611-irq-state {
  pins = "gpio8";
  function = "gpio";
  bias-disable;
 };

 lt9611_rst_pin: lt9611-rst-state {
  pins = "gpio7";
  function = "gpio";
  output-high;
 };

 wcd_default: wcd-reset-n-active-state {
  pins = "gpio108";
  function = "gpio";
  drive-strength = <16>;
  bias-disable;
  output-low;
 };

 wlan_en: wlan-en-state {
  pins = "gpio80";
  function = "gpio";
  drive-strength = <8>;
  bias-pull-down;
 };
};

&uart7 {
 status = "okay";
};

&uart14 {
 status = "okay";

 bluetooth {
  compatible = "qcom,wcn7850-bt";

  vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
  vddaon-supply = <&vreg_pmu_aon_0p59>;
  vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
  vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
  vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
  vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
  vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;

  max-speed = <3200000>;
 };
};

&ufs_mem_hc {
 reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;

 vcc-supply = <&vreg_l17b_2p5>;
 vcc-max-microamp = <1300000>;
 vccq-supply = <&vreg_l1g_1p2>;
 vccq-max-microamp = <1200000>;
 vdd-hba-supply = <&vreg_l3g_1p2>;

 status = "okay";
};

&ufs_mem_phy {
 vdda-phy-supply = <&vreg_l1d_0p88>;
 vdda-pll-supply = <&vreg_l3e_1p2>;

 status = "okay";
};

&usb_1 {
 status = "okay";
};

&usb_1_dwc3_hs {
 remote-endpoint = <&pmic_glink_hs_in>;
};

&usb_1_hsphy {
 vdd-supply = <&vreg_l1e_0p88>;
 vdda12-supply = <&vreg_l3e_1p2>;

 phys = <&pm8550b_eusb2_repeater>;

 status = "okay";
};

&usb_dp_qmpphy {
 vdda-phy-supply = <&vreg_l3e_1p2>;
 vdda-pll-supply = <&vreg_l3f_0p88>;

 status = "okay";
};

&usb_dp_qmpphy_out {
 remote-endpoint = <&pmic_glink_ss_in>;
};

&xo_board {
 clock-frequency = <76800000>;
};