// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
/*
* Copyright ( c ) 2015 , 2016 Intel Corporation .
*/
#include <linux/delay.h>
#include <linux/pci.h>
#include <linux/vmalloc.h>
#include "hfi.h"
/* for the given bus number, return the CSR for reading an i2c line */
static inline u32 i2c_in_csr(u32 bus_num)
{
return bus_num ? ASIC_QSFP2_IN : ASIC_QSFP1_IN;
}
/* for the given bus number, return the CSR for writing an i2c line */
static inline u32 i2c_oe_csr(u32 bus_num)
{
return bus_num ? ASIC_QSFP2_OE : ASIC_QSFP1_OE;
}
static void hfi1_setsda(void *data, int state)
{
struct hfi1_i2c_bus *bus = (struct hfi1_i2c_bus *)data;
struct hfi1_devdata *dd = bus->controlling_dd;
u64 reg;
u32 target_oe;
target_oe = i2c_oe_csr(bus->num);
reg = read_csr(dd, target_oe);
/*
* The OE bit value is inverted and connected to the pin . When
* OE is 0 the pin is left to be pulled up , when the OE is 1
* the pin is driven low . This matches the " open drain " or " open
* collector " convention .
*/
if (state)
reg &= ~QSFP_HFI0_I2CDAT;
else
reg |= QSFP_HFI0_I2CDAT;
write_csr(dd, target_oe, reg);
/* do a read to force the write into the chip */
(void )read_csr(dd, target_oe);
}
static void hfi1_setscl(void *data, int state)
{
struct hfi1_i2c_bus *bus = (struct hfi1_i2c_bus *)data;
struct hfi1_devdata *dd = bus->controlling_dd;
u64 reg;
u32 target_oe;
target_oe = i2c_oe_csr(bus->num);
reg = read_csr(dd, target_oe);
/*
* The OE bit value is inverted and connected to the pin . When
* OE is 0 the pin is left to be pulled up , when the OE is 1
* the pin is driven low . This matches the " open drain " or " open
* collector " convention .
*/
if (state)
reg &= ~QSFP_HFI0_I2CCLK;
else
reg |= QSFP_HFI0_I2CCLK;
write_csr(dd, target_oe, reg);
/* do a read to force the write into the chip */
(void )read_csr(dd, target_oe);
}
static int hfi1_getsda(void *data)
{
struct hfi1_i2c_bus *bus = (struct hfi1_i2c_bus *)data;
u64 reg;
u32 target_in;
hfi1_setsda(data, 1 ); /* clear OE so we do not pull line down */
udelay(2 ); /* 1us pull up + 250ns hold */
target_in = i2c_in_csr(bus->num);
reg = read_csr(bus->controlling_dd, target_in);
return !!(reg & QSFP_HFI0_I2CDAT);
}
static int hfi1_getscl(void *data)
{
struct hfi1_i2c_bus *bus = (struct hfi1_i2c_bus *)data;
u64 reg;
u32 target_in;
hfi1_setscl(data, 1 ); /* clear OE so we do not pull line down */
udelay(2 ); /* 1us pull up + 250ns hold */
target_in = i2c_in_csr(bus->num);
reg = read_csr(bus->controlling_dd, target_in);
return !!(reg & QSFP_HFI0_I2CCLK);
}
/*
* Allocate and initialize the given i2c bus number .
* Returns NULL on failure .
*/
static struct hfi1_i2c_bus *init_i2c_bus(struct hfi1_devdata *dd,
struct hfi1_asic_data *ad, int num)
{
struct hfi1_i2c_bus *bus;
int ret;
bus = kzalloc(sizeof (*bus), GFP_KERNEL);
if (!bus)
return NULL;
bus->controlling_dd = dd;
bus->num = num; /* our bus number */
bus->algo.setsda = hfi1_setsda;
bus->algo.setscl = hfi1_setscl;
bus->algo.getsda = hfi1_getsda;
bus->algo.getscl = hfi1_getscl;
bus->algo.udelay = 5 ;
bus->algo.timeout = usecs_to_jiffies(100000 );
bus->algo.data = bus;
bus->adapter.owner = THIS_MODULE;
bus->adapter.algo_data = &bus->algo;
bus->adapter.dev.parent = &dd->pcidev->dev;
snprintf(bus->adapter.name, sizeof (bus->adapter.name),
"hfi1_i2c%d" , num);
ret = i2c_bit_add_bus(&bus->adapter);
if (ret) {
dd_dev_info(dd, "%s: unable to add i2c bus %d, err %d\n" ,
__func__, num, ret);
kfree(bus);
return NULL;
}
return bus;
}
/*
* Initialize i2c buses .
* Return 0 on success , - errno on error .
*/
int set_up_i2c(struct hfi1_devdata *dd, struct hfi1_asic_data *ad)
{
ad->i2c_bus0 = init_i2c_bus(dd, ad, 0 );
ad->i2c_bus1 = init_i2c_bus(dd, ad, 1 );
if (!ad->i2c_bus0 || !ad->i2c_bus1)
return -ENOMEM;
return 0 ;
};
static void clean_i2c_bus(struct hfi1_i2c_bus *bus)
{
if (bus) {
i2c_del_adapter(&bus->adapter);
kfree(bus);
}
}
void clean_up_i2c(struct hfi1_devdata *dd, struct hfi1_asic_data *ad)
{
if (!ad)
return ;
clean_i2c_bus(ad->i2c_bus0);
ad->i2c_bus0 = NULL;
clean_i2c_bus(ad->i2c_bus1);
ad->i2c_bus1 = NULL;
}
static int i2c_bus_write(struct hfi1_devdata *dd, struct hfi1_i2c_bus *i2c,
u8 slave_addr, int offset, int offset_size,
u8 *data, u16 len)
{
int ret;
int num_msgs;
u8 offset_bytes[2 ];
struct i2c_msg msgs[2 ];
switch (offset_size) {
case 0 :
num_msgs = 1 ;
msgs[0 ].addr = slave_addr;
msgs[0 ].flags = 0 ;
msgs[0 ].len = len;
msgs[0 ].buf = data;
break ;
case 2 :
offset_bytes[1 ] = (offset >> 8 ) & 0 xff;
fallthrough;
case 1 :
num_msgs = 2 ;
offset_bytes[0 ] = offset & 0 xff;
msgs[0 ].addr = slave_addr;
msgs[0 ].flags = 0 ;
msgs[0 ].len = offset_size;
msgs[0 ].buf = offset_bytes;
msgs[1 ].addr = slave_addr;
msgs[1 ].flags = I2C_M_NOSTART;
msgs[1 ].len = len;
msgs[1 ].buf = data;
break ;
default :
return -EINVAL;
}
i2c->controlling_dd = dd;
ret = i2c_transfer(&i2c->adapter, msgs, num_msgs);
if (ret != num_msgs) {
dd_dev_err(dd, "%s: bus %d, i2c slave 0x%x, offset 0x%x, len 0x%x; write failed, ret %d\n" ,
__func__, i2c->num, slave_addr, offset, len, ret);
return ret < 0 ? ret : -EIO;
}
return 0 ;
}
static int i2c_bus_read(struct hfi1_devdata *dd, struct hfi1_i2c_bus *bus,
u8 slave_addr, int offset, int offset_size,
u8 *data, u16 len)
{
int ret;
int num_msgs;
u8 offset_bytes[2 ];
struct i2c_msg msgs[2 ];
switch (offset_size) {
case 0 :
num_msgs = 1 ;
msgs[0 ].addr = slave_addr;
msgs[0 ].flags = I2C_M_RD;
msgs[0 ].len = len;
msgs[0 ].buf = data;
break ;
case 2 :
offset_bytes[1 ] = (offset >> 8 ) & 0 xff;
fallthrough;
case 1 :
num_msgs = 2 ;
offset_bytes[0 ] = offset & 0 xff;
msgs[0 ].addr = slave_addr;
msgs[0 ].flags = 0 ;
msgs[0 ].len = offset_size;
msgs[0 ].buf = offset_bytes;
msgs[1 ].addr = slave_addr;
msgs[1 ].flags = I2C_M_RD;
msgs[1 ].len = len;
msgs[1 ].buf = data;
break ;
default :
return -EINVAL;
}
bus->controlling_dd = dd;
ret = i2c_transfer(&bus->adapter, msgs, num_msgs);
if (ret != num_msgs) {
dd_dev_err(dd, "%s: bus %d, i2c slave 0x%x, offset 0x%x, len 0x%x; read failed, ret %d\n" ,
__func__, bus->num, slave_addr, offset, len, ret);
return ret < 0 ? ret : -EIO;
}
return 0 ;
}
/*
* Raw i2c write . No set - up or lock checking .
*
* Return 0 on success , - errno on error .
*/
static int __i2c_write(struct hfi1_pportdata *ppd, u32 target, int i2c_addr,
int offset, void *bp, int len)
{
struct hfi1_devdata *dd = ppd->dd;
struct hfi1_i2c_bus *bus;
u8 slave_addr;
int offset_size;
bus = target ? dd->asic_data->i2c_bus1 : dd->asic_data->i2c_bus0;
slave_addr = (i2c_addr & 0 xff) >> 1 ; /* convert to 7-bit addr */
offset_size = (i2c_addr >> 8 ) & 0 x3;
return i2c_bus_write(dd, bus, slave_addr, offset, offset_size, bp, len);
}
/*
* Caller must hold the i2c chain resource .
*
* Return number of bytes written , or - errno .
*/
int i2c_write(struct hfi1_pportdata *ppd, u32 target, int i2c_addr, int offset,
void *bp, int len)
{
int ret;
if (!check_chip_resource(ppd->dd, i2c_target(target), __func__))
return -EACCES;
ret = __i2c_write(ppd, target, i2c_addr, offset, bp, len);
if (ret)
return ret;
return len;
}
/*
* Raw i2c read . No set - up or lock checking .
*
* Return 0 on success , - errno on error .
*/
static int __i2c_read(struct hfi1_pportdata *ppd, u32 target, int i2c_addr,
int offset, void *bp, int len)
{
struct hfi1_devdata *dd = ppd->dd;
struct hfi1_i2c_bus *bus;
u8 slave_addr;
int offset_size;
bus = target ? dd->asic_data->i2c_bus1 : dd->asic_data->i2c_bus0;
slave_addr = (i2c_addr & 0 xff) >> 1 ; /* convert to 7-bit addr */
offset_size = (i2c_addr >> 8 ) & 0 x3;
return i2c_bus_read(dd, bus, slave_addr, offset, offset_size, bp, len);
}
/*
* Caller must hold the i2c chain resource .
*
* Return number of bytes read , or - errno .
*/
int i2c_read(struct hfi1_pportdata *ppd, u32 target, int i2c_addr, int offset,
void *bp, int len)
{
int ret;
if (!check_chip_resource(ppd->dd, i2c_target(target), __func__))
return -EACCES;
ret = __i2c_read(ppd, target, i2c_addr, offset, bp, len);
if (ret)
return ret;
return len;
}
/*
* Write page n , offset m of QSFP memory as defined by SFF 8636
* by writing @ addr = ( ( 256 * n ) + m )
*
* Caller must hold the i2c chain resource .
*
* Return number of bytes written or - errno .
*/
int qsfp_write(struct hfi1_pportdata *ppd, u32 target, int addr, void *bp,
int len)
{
int count = 0 ;
int offset;
int nwrite;
int ret = 0 ;
u8 page;
if (!check_chip_resource(ppd->dd, i2c_target(target), __func__))
return -EACCES;
while (count < len) {
/*
* Set the qsfp page based on a zero - based address
* and a page size of QSFP_PAGESIZE bytes .
*/
page = (u8)(addr / QSFP_PAGESIZE);
ret = __i2c_write(ppd, target, QSFP_DEV | QSFP_OFFSET_SIZE,
QSFP_PAGE_SELECT_BYTE_OFFS, &page, 1 );
/* QSFPs require a 5-10msec delay after write operations */
mdelay(5 );
if (ret) {
hfi1_dev_porterr(ppd->dd, ppd->port,
"QSFP chain %d can't write QSFP_PAGE_SELECT_BYTE: %d\n" ,
target, ret);
break ;
}
offset = addr % QSFP_PAGESIZE;
nwrite = len - count;
/* truncate write to boundary if crossing boundary */
if (((addr % QSFP_RW_BOUNDARY) + nwrite) > QSFP_RW_BOUNDARY)
nwrite = QSFP_RW_BOUNDARY - (addr % QSFP_RW_BOUNDARY);
ret = __i2c_write(ppd, target, QSFP_DEV | QSFP_OFFSET_SIZE,
offset, bp + count, nwrite);
/* QSFPs require a 5-10msec delay after write operations */
mdelay(5 );
if (ret) /* stop on error */
break ;
count += nwrite;
addr += nwrite;
}
if (ret < 0 )
return ret;
return count;
}
/*
* Access page n , offset m of QSFP memory as defined by SFF 8636
* by reading @ addr = ( ( 256 * n ) + m )
*
* Caller must hold the i2c chain resource .
*
* Return the number of bytes read or - errno .
*/
int qsfp_read(struct hfi1_pportdata *ppd, u32 target, int addr, void *bp,
int len)
{
int count = 0 ;
int offset;
int nread;
int ret = 0 ;
u8 page;
if (!check_chip_resource(ppd->dd, i2c_target(target), __func__))
return -EACCES;
while (count < len) {
/*
* Set the qsfp page based on a zero - based address
* and a page size of QSFP_PAGESIZE bytes .
*/
page = (u8)(addr / QSFP_PAGESIZE);
ret = __i2c_write(ppd, target, QSFP_DEV | QSFP_OFFSET_SIZE,
QSFP_PAGE_SELECT_BYTE_OFFS, &page, 1 );
/* QSFPs require a 5-10msec delay after write operations */
mdelay(5 );
if (ret) {
hfi1_dev_porterr(ppd->dd, ppd->port,
"QSFP chain %d can't write QSFP_PAGE_SELECT_BYTE: %d\n" ,
target, ret);
break ;
}
offset = addr % QSFP_PAGESIZE;
nread = len - count;
/* truncate read to boundary if crossing boundary */
if (((addr % QSFP_RW_BOUNDARY) + nread) > QSFP_RW_BOUNDARY)
nread = QSFP_RW_BOUNDARY - (addr % QSFP_RW_BOUNDARY);
ret = __i2c_read(ppd, target, QSFP_DEV | QSFP_OFFSET_SIZE,
offset, bp + count, nread);
if (ret) /* stop on error */
break ;
count += nread;
addr += nread;
}
if (ret < 0 )
return ret;
return count;
}
/*
* Perform a stand - alone single QSFP read . Acquire the resource , do the
* read , then release the resource .
*/
int one_qsfp_read(struct hfi1_pportdata *ppd, u32 target, int addr, void *bp,
int len)
{
struct hfi1_devdata *dd = ppd->dd;
u32 resource = qsfp_resource(dd);
int ret;
ret = acquire_chip_resource(dd, resource, QSFP_WAIT);
if (ret)
return ret;
ret = qsfp_read(ppd, target, addr, bp, len);
release_chip_resource(dd, resource);
return ret;
}
/*
* This function caches the QSFP memory range in 128 byte chunks .
* As an example , the next byte after address 255 is byte 128 from
* upper page 01 H ( if existing ) rather than byte 0 from lower page 00 H .
* Access page n , offset m of QSFP memory as defined by SFF 8636
* in the cache by reading byte ( ( 128 * n ) + m )
* The calls to qsfp_ { read , write } in this function correctly handle the
* address map difference between this mapping and the mapping implemented
* by those functions
*
* The caller must be holding the QSFP i2c chain resource .
*/
int refresh_qsfp_cache(struct hfi1_pportdata *ppd, struct qsfp_data *cp)
{
u32 target = ppd->dd->hfi1_id;
int ret;
unsigned long flags;
u8 *cache = &cp->cache[0 ];
/* ensure sane contents on invalid reads, for cable swaps */
memset(cache, 0 , (QSFP_MAX_NUM_PAGES * 128 ));
spin_lock_irqsave(&ppd->qsfp_info.qsfp_lock, flags);
ppd->qsfp_info.cache_valid = 0 ;
spin_unlock_irqrestore(&ppd->qsfp_info.qsfp_lock, flags);
if (!qsfp_mod_present(ppd)) {
ret = -ENODEV;
goto bail;
}
ret = qsfp_read(ppd, target, 0 , cache, QSFP_PAGESIZE);
if (ret != QSFP_PAGESIZE) {
dd_dev_info(ppd->dd,
"%s: Page 0 read failed, expected %d, got %d\n" ,
__func__, QSFP_PAGESIZE, ret);
goto bail;
}
/* Is paging enabled? */
if (!(cache[2 ] & 4 )) {
/* Paging enabled, page 03 required */
if ((cache[195 ] & 0 xC0) == 0 xC0) {
/* all */
ret = qsfp_read(ppd, target, 384 , cache + 256 , 128 );
if (ret <= 0 || ret != 128 ) {
dd_dev_info(ppd->dd, "%s failed\n" , __func__);
goto bail;
}
ret = qsfp_read(ppd, target, 640 , cache + 384 , 128 );
if (ret <= 0 || ret != 128 ) {
dd_dev_info(ppd->dd, "%s failed\n" , __func__);
goto bail;
}
ret = qsfp_read(ppd, target, 896 , cache + 512 , 128 );
if (ret <= 0 || ret != 128 ) {
dd_dev_info(ppd->dd, "%s failed\n" , __func__);
goto bail;
}
} else if ((cache[195 ] & 0 x80) == 0 x80) {
/* only page 2 and 3 */
ret = qsfp_read(ppd, target, 640 , cache + 384 , 128 );
if (ret <= 0 || ret != 128 ) {
dd_dev_info(ppd->dd, "%s failed\n" , __func__);
goto bail;
}
ret = qsfp_read(ppd, target, 896 , cache + 512 , 128 );
if (ret <= 0 || ret != 128 ) {
dd_dev_info(ppd->dd, "%s failed\n" , __func__);
goto bail;
}
} else if ((cache[195 ] & 0 x40) == 0 x40) {
/* only page 1 and 3 */
ret = qsfp_read(ppd, target, 384 , cache + 256 , 128 );
if (ret <= 0 || ret != 128 ) {
dd_dev_info(ppd->dd, "%s failed\n" , __func__);
goto bail;
}
ret = qsfp_read(ppd, target, 896 , cache + 512 , 128 );
if (ret <= 0 || ret != 128 ) {
dd_dev_info(ppd->dd, "%s failed\n" , __func__);
goto bail;
}
} else {
/* only page 3 */
ret = qsfp_read(ppd, target, 896 , cache + 512 , 128 );
if (ret <= 0 || ret != 128 ) {
dd_dev_info(ppd->dd, "%s failed\n" , __func__);
goto bail;
}
}
}
spin_lock_irqsave(&ppd->qsfp_info.qsfp_lock, flags);
ppd->qsfp_info.cache_valid = 1 ;
ppd->qsfp_info.cache_refresh_required = 0 ;
spin_unlock_irqrestore(&ppd->qsfp_info.qsfp_lock, flags);
return 0 ;
bail:
memset(cache, 0 , (QSFP_MAX_NUM_PAGES * 128 ));
return ret;
}
const char * const hfi1_qsfp_devtech[16 ] = {
"850nm VCSEL" , "1310nm VCSEL" , "1550nm VCSEL" , "1310nm FP" ,
"1310nm DFB" , "1550nm DFB" , "1310nm EML" , "1550nm EML" ,
"Cu Misc" , "1490nm DFB" , "Cu NoEq" , "Cu Eq" ,
"Undef" , "Cu Active BothEq" , "Cu FarEq" , "Cu NearEq"
};
#define QSFP_DUMP_CHUNK 16 /* Holds longest string */
#define QSFP_DEFAULT_HDR_CNT 224
#define QSFP_PWR(pbyte) (((pbyte) >> 6 ) & 3 )
#define QSFP_HIGH_PWR(pbyte) ((pbyte) & 3 )
/* For use with QSFP_HIGH_PWR macro */
#define QSFP_HIGH_PWR_UNUSED 0 /* Bits [1:0] = 00 implies low power module */
/*
* Takes power class byte [ Page 00 Byte 129 ] in SFF 8636
* Returns power class as integer ( 1 through 7 , per SFF 8636 rev 2 . 4 )
*/
int get_qsfp_power_class(u8 power_byte)
{
if (QSFP_HIGH_PWR(power_byte) == QSFP_HIGH_PWR_UNUSED)
/* power classes count from 1, their bit encodings from 0 */
return (QSFP_PWR(power_byte) + 1 );
/*
* 00 in the high power classes stands for unused , bringing
* balance to the off - by - 1 offset above , we add 4 here to
* account for the difference between the low and high power
* groups
*/
return (QSFP_HIGH_PWR(power_byte) + 4 );
}
int qsfp_mod_present(struct hfi1_pportdata *ppd)
{
struct hfi1_devdata *dd = ppd->dd;
u64 reg;
reg = read_csr(dd, dd->hfi1_id ? ASIC_QSFP2_IN : ASIC_QSFP1_IN);
return !(reg & QSFP_HFI0_MODPRST_N);
}
/*
* This function maps QSFP memory addresses in 128 byte chunks in the following
* fashion per the CableInfo SMA query definition in the IBA 1 . 3 spec / OPA Gen 1
* spec
* For addr 000 - 127 , lower page 00 h
* For addr 128 - 255 , upper page 00 h
* For addr 256 - 383 , upper page 01 h
* For addr 384 - 511 , upper page 02 h
* For addr 512 - 639 , upper page 03 h
*
* For addresses beyond this range , it returns the invalid range of data buffer
* set to 0 .
* For upper pages that are optional , if they are not valid , returns the
* particular range of bytes in the data buffer set to 0 .
*/
int get_cable_info(struct hfi1_devdata *dd, u32 port_num, u32 addr, u32 len,
u8 *data)
{
struct hfi1_pportdata *ppd;
u32 excess_len = len;
int ret = 0 , offset = 0 ;
if (port_num > dd->num_pports || port_num < 1 ) {
dd_dev_info(dd, "%s: Invalid port number %d\n" ,
__func__, port_num);
ret = -EINVAL;
goto set_zeroes;
}
ppd = dd->pport + (port_num - 1 );
if (!qsfp_mod_present(ppd)) {
ret = -ENODEV;
goto set_zeroes;
}
if (!ppd->qsfp_info.cache_valid) {
ret = -EINVAL;
goto set_zeroes;
}
if (addr >= (QSFP_MAX_NUM_PAGES * 128 )) {
ret = -ERANGE;
goto set_zeroes;
}
if ((addr + len) > (QSFP_MAX_NUM_PAGES * 128 )) {
excess_len = (addr + len) - (QSFP_MAX_NUM_PAGES * 128 );
memcpy(data, &ppd->qsfp_info.cache[addr], (len - excess_len));
data += (len - excess_len);
goto set_zeroes;
}
memcpy(data, &ppd->qsfp_info.cache[addr], len);
if (addr <= QSFP_MONITOR_VAL_END &&
(addr + len) >= QSFP_MONITOR_VAL_START) {
/* Overlap with the dynamic channel monitor range */
if (addr < QSFP_MONITOR_VAL_START) {
if (addr + len <= QSFP_MONITOR_VAL_END)
len = addr + len - QSFP_MONITOR_VAL_START;
else
len = QSFP_MONITOR_RANGE;
offset = QSFP_MONITOR_VAL_START - addr;
addr = QSFP_MONITOR_VAL_START;
} else if (addr == QSFP_MONITOR_VAL_START) {
offset = 0 ;
if (addr + len > QSFP_MONITOR_VAL_END)
len = QSFP_MONITOR_RANGE;
} else {
offset = 0 ;
if (addr + len > QSFP_MONITOR_VAL_END)
len = QSFP_MONITOR_VAL_END - addr + 1 ;
}
/* Refresh the values of the dynamic monitors from the cable */
ret = one_qsfp_read(ppd, dd->hfi1_id, addr, data + offset, len);
if (ret != len) {
ret = -EAGAIN;
goto set_zeroes;
}
}
return 0 ;
set_zeroes:
memset(data, 0 , excess_len);
return ret;
}
static const char *pwr_codes[8 ] = {"N/AW" ,
"1.5W" ,
"2.0W" ,
"2.5W" ,
"3.5W" ,
"4.0W" ,
"4.5W" ,
"5.0W"
};
int qsfp_dump(struct hfi1_pportdata *ppd, char *buf, int len)
{
u8 *cache = &ppd->qsfp_info.cache[0 ];
u8 bin_buff[QSFP_DUMP_CHUNK];
char lenstr[6 ];
int sofar;
int bidx = 0 ;
u8 *atten = &cache[QSFP_ATTEN_OFFS];
u8 *vendor_oui = &cache[QSFP_VOUI_OFFS];
u8 power_byte = 0 ;
sofar = 0 ;
lenstr[0 ] = ' ' ;
lenstr[1 ] = '\0' ;
if (ppd->qsfp_info.cache_valid) {
if (QSFP_IS_CU(cache[QSFP_MOD_TECH_OFFS]))
snprintf(lenstr, sizeof (lenstr), "%dM " ,
cache[QSFP_MOD_LEN_OFFS]);
power_byte = cache[QSFP_MOD_PWR_OFFS];
sofar += scnprintf(buf + sofar, len - sofar, "PWR:%.3sW\n" ,
pwr_codes[get_qsfp_power_class(power_byte)]);
sofar += scnprintf(buf + sofar, len - sofar, "TECH:%s%s\n" ,
lenstr,
hfi1_qsfp_devtech[(cache[QSFP_MOD_TECH_OFFS]) >> 4 ]);
sofar += scnprintf(buf + sofar, len - sofar, "Vendor:%.*s\n" ,
QSFP_VEND_LEN, &cache[QSFP_VEND_OFFS]);
sofar += scnprintf(buf + sofar, len - sofar, "OUI:%06X\n" ,
QSFP_OUI(vendor_oui));
sofar += scnprintf(buf + sofar, len - sofar, "Part#:%.*s\n" ,
QSFP_PN_LEN, &cache[QSFP_PN_OFFS]);
sofar += scnprintf(buf + sofar, len - sofar, "Rev:%.*s\n" ,
QSFP_REV_LEN, &cache[QSFP_REV_OFFS]);
if (QSFP_IS_CU(cache[QSFP_MOD_TECH_OFFS]))
sofar += scnprintf(buf + sofar, len - sofar,
"Atten:%d, %d\n" ,
QSFP_ATTEN_SDR(atten),
QSFP_ATTEN_DDR(atten));
sofar += scnprintf(buf + sofar, len - sofar, "Serial:%.*s\n" ,
QSFP_SN_LEN, &cache[QSFP_SN_OFFS]);
sofar += scnprintf(buf + sofar, len - sofar, "Date:%.*s\n" ,
QSFP_DATE_LEN, &cache[QSFP_DATE_OFFS]);
sofar += scnprintf(buf + sofar, len - sofar, "Lot:%.*s\n" ,
QSFP_LOT_LEN, &cache[QSFP_LOT_OFFS]);
while (bidx < QSFP_DEFAULT_HDR_CNT) {
int iidx;
memcpy(bin_buff, &cache[bidx], QSFP_DUMP_CHUNK);
for (iidx = 0 ; iidx < QSFP_DUMP_CHUNK; ++iidx) {
sofar += scnprintf(buf + sofar, len - sofar,
" %02X" , bin_buff[iidx]);
}
sofar += scnprintf(buf + sofar, len - sofar, "\n" );
bidx += QSFP_DUMP_CHUNK;
}
}
return sofar;
}
Messung V0.5 in Prozent C=92 H=94 G=92
¤ Dauer der Verarbeitung: 0.12 Sekunden
¤
*© Formatika GbR, Deutschland