/* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright (C) 2018 Oleksij Rempel <linux@rempel-privat.de> * * Driver for Alcor Micro AU6601 and AU6621 controllers #ifndef __ALCOR_PCI_H#define __ALCOR_PCI_H#define ALCOR_SD_CARD 0#define ALCOR_MS_CARD 1#define DRV_NAME_ALCOR_PCI "alcor_pci" #define DRV_NAME_ALCOR_PCI_SDMMC "alcor_sdmmc" #define DRV_NAME_ALCOR_PCI_MS "alcor_ms" #define PCI_ID_ALCOR_MICRO 0x1AEA#define PCI_ID_AU6601 0x6601#define PCI_ID_AU6621 0x6621#define PCI_ID_AU6625 0x6625#define MHZ_TO_HZ(freq) ((freq) * 1000 * 1000)#define AU6601_BASE_CLOCK 31000000#define AU6601_MIN_CLOCK 150000#define AU6601_MAX_CLOCK 208000000#define AU6601_MAX_DMA_SEGMENTS 64#define AU6601_MAX_PIO_SEGMENTS 1#define AU6601_MAX_DMA_BLOCK_SIZE 0x1000#define AU6601_MAX_PIO_BLOCK_SIZE 0x200#define AU6601_MAX_DMA_BLOCKS 1#define AU6601_DMA_LOCAL_SEGMENTS 1/* registers spotter by reverse engineering but still * with unknown functionality: * 0x10 - ADMA phy address. AU6621 only? * 0x51 - LED ctrl? * 0x52 - unknown * 0x61 - LED related? Always toggled BIT0 * 0x63 - Same as 0x61? * 0x77 - unknown /* SDMA phy address. Higher then 0x0800.0000? * The au6601 and au6621 have different DMA engines with different issues. One * For example au6621 engine is triggered by addr change. No other interaction * is needed. This means, if we get two buffers with same address, then engine * will stall. #define AU6601_REG_SDMA_ADDR 0x00#define AU6601_SDMA_MASK 0xffffffff#define AU6601_DMA_BOUNDARY 0x05#define AU6621_DMA_PAGE_CNT 0x05/* PIO */ #define AU6601_REG_BUFFER 0x08/* ADMA ctrl? AU6621 only. */ #define AU6621_DMA_CTRL 0x0c#define AU6621_DMA_ENABLE BIT(0)/* CMD index */ #define AU6601_REG_CMD_OPCODE 0x23/* CMD parametr */ #define AU6601_REG_CMD_ARG 0x24/* CMD response 4x4 Bytes */ #define AU6601_REG_CMD_RSP0 0x30#define AU6601_REG_CMD_RSP1 0x34#define AU6601_REG_CMD_RSP2 0x38#define AU6601_REG_CMD_RSP3 0x3C/* default timeout set to 125: 125 * 40ms = 5 sec * how exactly it is calculated? #define AU6601_TIME_OUT_CTRL 0x69/* Block size for SDMA or PIO */ #define AU6601_REG_BLOCK_SIZE 0x6c/* Some power related reg, used together with AU6601_OUTPUT_ENABLE */ #define AU6601_POWER_CONTROL 0x70/* PLL ctrl */ #define AU6601_CLK_SELECT 0x72#define AU6601_CLK_OVER_CLK 0x80#define AU6601_CLK_384_MHZ 0x30#define AU6601_CLK_125_MHZ 0x20#define AU6601_CLK_48_MHZ 0x10#define AU6601_CLK_EXT_PLL 0x04#define AU6601_CLK_X2_MODE 0x02#define AU6601_CLK_ENABLE 0x01#define AU6601_CLK_31_25_MHZ 0x00#define AU6601_CLK_DIVIDER 0x73#define AU6601_INTERFACE_MODE_CTRL 0x74#define AU6601_DLINK_MODE 0x80#define AU6601_INTERRUPT_DELAY_TIME 0x40#define AU6601_SIGNAL_REQ_CTRL 0x30#define AU6601_MS_CARD_WP BIT(3)#define AU6601_SD_CARD_WP BIT(0)/* same register values are used for: * - AU6601_OUTPUT_ENABLE * - AU6601_POWER_CONTROL #define AU6601_ACTIVE_CTRL 0x75#define AU6601_XD_CARD BIT(4)/* AU6601_MS_CARD_ACTIVE - will cativate MS card section? */ #define AU6601_MS_CARD BIT(3)#define AU6601_SD_CARD BIT(0)/* card slot state. It should automatically detect type of * the card #define AU6601_DETECT_STATUS 0x76#define AU6601_DETECT_EN BIT(7)#define AU6601_MS_DETECTED BIT(3)#define AU6601_SD_DETECTED BIT(0)#define AU6601_DETECT_STATUS_M 0xf#define AU6601_REG_SW_RESET 0x79#define AU6601_BUF_CTRL_RESET BIT(7)#define AU6601_RESET_DATA BIT(3)#define AU6601_RESET_CMD BIT(0)#define AU6601_OUTPUT_ENABLE 0x7a#define AU6601_PAD_DRIVE0 0x7b#define AU6601_PAD_DRIVE1 0x7c#define AU6601_PAD_DRIVE2 0x7d/* read EEPROM? */ #define AU6601_FUNCTION 0x7f#define AU6601_CMD_XFER_CTRL 0x81#define AU6601_CMD_17_BYTE_CRC 0xc0#define AU6601_CMD_6_BYTE_WO_CRC 0x80#define AU6601_CMD_6_BYTE_CRC 0x40#define AU6601_CMD_START_XFER 0x20#define AU6601_CMD_STOP_WAIT_RDY 0x10#define AU6601_CMD_NO_RESP 0x00#define AU6601_REG_BUS_CTRL 0x82#define AU6601_BUS_WIDTH_4BIT 0x20#define AU6601_BUS_WIDTH_8BIT 0x10#define AU6601_BUS_WIDTH_1BIT 0x00#define AU6601_DATA_XFER_CTRL 0x83#define AU6601_DATA_WRITE BIT(7)#define AU6601_DATA_DMA_MODE BIT(6)#define AU6601_DATA_START_XFER BIT(0)#define AU6601_DATA_PIN_STATE 0x84#define AU6601_BUS_STAT_CMD BIT(15)/* BIT(4) - BIT(7) are permanently 1. * May be reserved or not attached DAT4-DAT7 #define AU6601_BUS_STAT_DAT3 BIT(3)#define AU6601_BUS_STAT_DAT2 BIT(2)#define AU6601_BUS_STAT_DAT1 BIT(1)#define AU6601_BUS_STAT_DAT0 BIT(0)#define AU6601_BUS_STAT_DAT_MASK 0xf#define AU6601_OPT 0x85#define AU6601_OPT_CMD_LINE_LEVEL 0x80#define AU6601_OPT_NCRC_16_CLK BIT(4)#define AU6601_OPT_CMD_NWT BIT(3)#define AU6601_OPT_STOP_CLK BIT(2)#define AU6601_OPT_DDR_MODE BIT(1)#define AU6601_OPT_SD_18V BIT(0)#define AU6601_CLK_DELAY 0x86#define AU6601_CLK_DATA_POSITIVE_EDGE 0x80#define AU6601_CLK_CMD_POSITIVE_EDGE 0x40#define AU6601_CLK_POSITIVE_EDGE_ALL (AU6601_CLK_CMD_POSITIVE_EDGE \#define AU6601_REG_INT_STATUS 0x90#define AU6601_REG_INT_ENABLE 0x94#define AU6601_INT_DATA_END_BIT_ERR BIT(22)#define AU6601_INT_DATA_CRC_ERR BIT(21)#define AU6601_INT_DATA_TIMEOUT_ERR BIT(20)#define AU6601_INT_CMD_INDEX_ERR BIT(19)#define AU6601_INT_CMD_END_BIT_ERR BIT(18)#define AU6601_INT_CMD_CRC_ERR BIT(17)#define AU6601_INT_CMD_TIMEOUT_ERR BIT(16)#define AU6601_INT_ERROR BIT(15)#define AU6601_INT_OVER_CURRENT_ERR BIT(8)#define AU6601_INT_CARD_INSERT BIT(7)#define AU6601_INT_CARD_REMOVE BIT(6)#define AU6601_INT_READ_BUF_RDY BIT(5)#define AU6601_INT_WRITE_BUF_RDY BIT(4)#define AU6601_INT_DMA_END BIT(3)#define AU6601_INT_DATA_END BIT(1)#define AU6601_INT_CMD_END BIT(0)#define AU6601_INT_NORMAL_MASK 0x00007FFF#define AU6601_INT_ERROR_MASK 0xFFFF8000#define AU6601_INT_CMD_MASK (AU6601_INT_CMD_END | \#define AU6601_INT_DATA_MASK (AU6601_INT_DATA_END | AU6601_INT_DMA_END | \#define AU6601_INT_ALL_MASK ((u32)-1)/* MS_CARD mode registers */ #define AU6601_MS_STATUS 0xa0#define AU6601_MS_BUS_MODE_CTRL 0xa1#define AU6601_MS_BUS_8BIT_MODE 0x03#define AU6601_MS_BUS_4BIT_MODE 0x01#define AU6601_MS_BUS_1BIT_MODE 0x00#define AU6601_MS_TPC_CMD 0xa2#define AU6601_MS_TPC_READ_PAGE_DATA 0x02#define AU6601_MS_TPC_READ_REG 0x04#define AU6601_MS_TPC_GET_INT 0x07#define AU6601_MS_TPC_WRITE_PAGE_DATA 0x0D#define AU6601_MS_TPC_WRITE_REG 0x0B#define AU6601_MS_TPC_SET_RW_REG_ADRS 0x08#define AU6601_MS_TPC_SET_CMD 0x0E#define AU6601_MS_TPC_EX_SET_CMD 0x09#define AU6601_MS_TPC_READ_SHORT_DATA 0x03#define AU6601_MS_TPC_WRITE_SHORT_DATA 0x0C#define AU6601_MS_TRANSFER_MODE 0xa3#define AU6601_MS_XFER_INT_TIMEOUT_CHK BIT(2)#define AU6601_MS_XFER_DMA_ENABLE BIT(1)#define AU6601_MS_XFER_START BIT(0)#define AU6601_MS_DATA_PIN_STATE 0xa4#define AU6601_MS_INT_STATUS 0xb0#define AU6601_MS_INT_ENABLE 0xb4#define AU6601_MS_INT_OVER_CURRENT_ERROR BIT(23)#define AU6601_MS_INT_DATA_CRC_ERROR BIT(21)#define AU6601_MS_INT_INT_TIMEOUT BIT(20)#define AU6601_MS_INT_INT_RESP_ERROR BIT(19)#define AU6601_MS_INT_CED_ERROR BIT(18)#define AU6601_MS_INT_TPC_TIMEOUT BIT(16)#define AU6601_MS_INT_ERROR BIT(15)#define AU6601_MS_INT_CARD_INSERT BIT(7)#define AU6601_MS_INT_CARD_REMOVE BIT(6)#define AU6601_MS_INT_BUF_READ_RDY BIT(5)#define AU6601_MS_INT_BUF_WRITE_RDY BIT(4)#define AU6601_MS_INT_DMA_END BIT(3)#define AU6601_MS_INT_TPC_END BIT(1)#define AU6601_MS_INT_DATA_MASK 0x00000038#define AU6601_MS_INT_TPC_MASK 0x003d8002#define AU6601_MS_INT_TPC_ERROR 0x003d0000#define ALCOR_PCIE_LINK_CTRL_OFFSET 0x10#define ALCOR_PCIE_LINK_CAP_OFFSET 0x0c#define ALCOR_CAP_START_OFFSET 0x34struct alcor_dev_cfg {struct alcor_pci_priv {struct pci_dev *pdev;struct pci_dev *parent_pdev;struct device *dev;void __iomem *iobase;unsigned int irq;unsigned long id; /* idr id */ struct alcor_dev_cfg *cfg;void alcor_write8(struct alcor_pci_priv *priv, u8 val, unsigned int addr);void alcor_write16(struct alcor_pci_priv *priv, u16 val, unsigned int addr);void alcor_write32(struct alcor_pci_priv *priv, u32 val, unsigned int addr);void alcor_write32be(struct alcor_pci_priv *priv, u32 val, unsigned int addr);struct alcor_pci_priv *priv, unsigned int addr);struct alcor_pci_priv *priv, unsigned int addr);struct alcor_pci_priv *priv, unsigned int addr);#endif
Messung V0.5 C=97 H=95 G=95
¤ Dauer der Verarbeitung: 0.11 Sekunden
(vorverarbeitet)
¤ *© Formatika GbR, Deutschland
