Spracherkennung für: .dtsi vermutete Sprache: Unknown {[0] [0] [0]} [Methode: Schwerpunktbildung, einfache Gewichte, sechs Dimensionen]
// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
/*
* Copyright (C) 2020 STMicroelectronics - All Rights Reserved
* Copyright (C) 2021 Rouven Czerwinski, Pengutronix
* Copyright (C) 2023, 2024 Leonard Göhrs, Pengutronix
*/
#include "stm32mp153.dtsi"
#include "stm32mp15xc.dtsi"
#include "stm32mp15xx-osd32.dtsi"
#include "stm32mp15xxac-pinctrl.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pwm/pwm.h>
/ {
aliases {
can0 = &m_can1;
ethernet0 = ðernet0;
i2c0 = &i2c1;
i2c1 = &i2c4;
mmc1 = &sdmmc2;
serial0 = &uart4;
serial1 = &usart3;
spi0 = &spi4;
};
chosen {
stdout-path = &uart4;
};
backlight: backlight {
compatible = "pwm-backlight";
power-supply = <&v3v3>;
brightness-levels = <0 31 63 95 127 159 191 223 255>;
default-brightness-level = <7>;
pwms = <&led_pwm 3 1000000 0>;
};
led-controller-cpu {
compatible = "gpio-leds";
led-0 {
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_HEARTBEAT;
gpios = <&gpioa 13 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
led_controller_io: led-controller-io {
compatible = "gpio-leds";
/*
* led-0 and led-1 are internally connected antiparallel to one
* another inside the ethernet jack like this:
* GPIO0 ---+---|led-0|>--+--- GPIO2
* +--<|led-1|---+
* E.g. only one of the LEDs can be illuminated at a time while
* the other output must be driven low.
* This should likely be implemented using a multi color LED
* driver for antiparallel LEDs.
*/
led-0 {
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
gpios = <&io_board_gpio 0 GPIO_ACTIVE_HIGH>;
};
led-1 {
color = <LED_COLOR_ID_ORANGE>;
function = LED_FUNCTION_LAN;
gpios = <&io_board_gpio 2 GPIO_ACTIVE_HIGH>;
};
};
reg_5v: regulator-5v {
compatible = "regulator-fixed";
regulator-name = "5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
};
reg_1v2: regulator-1v2 {
compatible = "regulator-fixed";
regulator-name = "1V2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
vin-supply = <®_5v>;
};
};
baseboard_eeprom: &sip_eeprom {
};
&crc1 {
status = "okay";
};
&cryp1 {
status = "okay";
};
&dts {
status = "okay";
};
ðernet0 {
assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
assigned-clock-parents = <&rcc PLL4_P>;
assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF */
pinctrl-names = "default", "sleep";
pinctrl-0 = <ðernet0_rgmii_pins_b>;
pinctrl-1 = <ðernet0_rgmii_sleep_pins_b>;
st,eth-clk-sel;
phy-mode = "rgmii-id";
phy-handle = <ðphy>;
status = "okay";
mdio {
compatible = "snps,dwmac-mdio";
#address-cells = <1>;
#size-cells = <0>;
ethphy: ethernet-phy@3 { /* KSZ9031RN */
reg = <3>;
reset-gpios = <&gpioe 11 GPIO_ACTIVE_LOW>; /* ETH_RST# */
interrupt-parent = <&gpioa>;
interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
reset-assert-us = <10000>;
reset-deassert-us = <300>;
micrel,force-master;
};
};
};
&gpioa {
gpio-line-names = "", "", "", "", "", /* 0 */
"", "ETH_INT", "", "", "", /* 5 */
"", "", "", "BOOTROM_LED", "", /* 10 */
""; /* 15 */
};
&gpiob {
gpio-line-names = "", "", "", "", "", /* 0 */
"", "", "", "", "", /* 5 */
"", "", "", "", "", /* 10 */
""; /* 15 */
};
&gpioc {
gpio-line-names = "", "", "", "", "", /* 0 */
"", "", "", "", "", /* 5 */
"", ""; /* 10 */
};
&gpiod {
gpio-line-names = "", "", "", "", "", /* 0 */
"", "", "LCD_TE", "", "", /* 5 */
"LCD_DC", "", "", "", "", /* 10 */
""; /* 15 */
};
&gpioe {
gpio-line-names = "LCD_CS", "", "", "", "", /* 0 */
"", "", "", "", "", /* 5 */
"", "", "", "", "", /* 10 */
""; /* 15 */
};
&gpiof {
gpio-line-names = "GPIO1", "GPIO2", "", "", "", /* 0 */
"", "", "", "", "", /* 5 */
"", "", "", "", "", /* 10 */
""; /* 15 */
};
&gpiog {
gpio-line-names = "", "", "", "", "", /* 0 */
"", "", "", "", "", /* 5 */
"", "", "", "", "", /* 10 */
""; /* 15 */
};
&gpioz {
gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", /* 0 */
"", "HWID4", "HWID5"; /* 5 */
};
&hash1 {
status = "okay";
};
&iwdg2 {
timeout-sec = <8>;
status = "okay";
};
&m_can1 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&m_can1_pins_b>;
pinctrl-1 = <&m_can1_sleep_pins_b>;
status = "okay";
termination-gpios = <&io_board_gpio 7 GPIO_ACTIVE_HIGH>;
termination-ohms = <120>;
};
&pmic {
regulators {
buck1-supply = <®_5v>; /* VIN */
buck2-supply = <®_5v>; /* VIN */
buck3-supply = <®_5v>; /* VIN */
buck4-supply = <®_5v>; /* VIN */
ldo2-supply = <®_5v>; /* PMIC_LDO25IN */
ldo4-supply = <®_5v>; /* VIN */
ldo5-supply = <®_5v>; /* PMIC_LDO25IN */
vref_ddr-supply = <®_5v>; /* VIN */
boost-supply = <®_5v>; /* PMIC_BSTIN */
pwr_sw2-supply = <&bst_out>; /* PMIC_SWIN */
};
};
&pwr_regulators {
vdd-supply = <&vdd>;
vdd_3v3_usbfs-supply = <&vdd_usb>;
};
&sdmmc2 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
vmmc-supply = <&v3v3>;
bus-width = <8>;
mmc-ddr-3_3v;
no-1-8-v;
non-removable;
no-sd;
no-sdio;
st,neg-edge;
status = "okay";
};
&spi4 {
pinctrl-names = "default";
pinctrl-0 = <&spi4_pins_a>;
cs-gpios = <&gpioe 0 GPIO_ACTIVE_LOW>;
status = "okay";
lcd: display@0 {
compatible = "shineworld,lh133k", "panel-mipi-dbi-spi";
reg = <0>;
power-supply = <&v3v3>;
io-supply = <&v3v3>;
backlight = <&backlight>;
dc-gpios = <&gpiod 10 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpioh 4 GPIO_ACTIVE_HIGH>;
spi-3wire;
spi-max-frequency = <32000000>;
width-mm = <23>;
height-mm = <23>;
rotation = <180>;
panel-timing {
hactive = <240>;
vactive = <240>;
hback-porch = <0>;
vback-porch = <0>;
clock-frequency = <0>;
hfront-porch = <0>;
hsync-len = <0>;
vfront-porch = <0>;
vsync-len = <0>;
};
};
};
&timers2 {
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
timer@1 {
status = "okay";
};
};
&timers3 {
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
timer@2 {
status = "okay";
};
};
&timers4 {
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
timer@3 {
status = "okay";
};
};
&timers8 {
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
led_pwm: pwm {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&pwm8_pins_b>;
pinctrl-1 = <&pwm8_sleep_pins_b>;
status = "okay";
};
};
&uart4 {
label = "debug";
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_a>;
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
};
&usart3 {
label = "external";
pinctrl-names = "default";
pinctrl-0 = <&usart3_pins_a>;
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
};
&usbh_ehci {
phys = <&usbphyc_port0>;
phy-names = "usb";
status = "okay";
};
&usbotg_hs {
phys = <&usbphyc_port1 0>;
phy-names = "usb2-phy";
vusb_d-supply = <&vdd_usb>;
vusb_a-supply = <®18>;
status = "okay";
};
&usbphyc {
status = "okay";
};
&usbphyc_port0 {
phy-supply = <&vdd_usb>;
};
&usbphyc_port1 {
phy-supply = <&vdd_usb>;
};
&v3v3_hdmi {
regulator-enable-ramp-delay = <1000>;
};
