// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2025, André Apitzsch <git@apitzsch.eu>
*/
/dts-v1/;
#include <dt-bindings/leds/common.h>
#include "msm8976.dtsi"
#include "pm8004.dtsi"
#include "pm8950.dtsi"
/ {
model = "BQ Aquaris X5 Plus (Longcheer L9360)";
compatible = "longcheer,l9360", "qcom,msm8976";
chassis-type = "handset";
aliases {
mmc0 = &sdhc_1; /* SDC1 eMMC slot */
mmc1 = &sdhc_2; /* SDC2 SD card slot */
};
chosen {
#address-cells = <2>;
#size-cells = <2>;
ranges;
framebuffer0: framebuffer@83200000 {
compatible = "simple-framebuffer";
reg = <0x0 0x83200000 0x0 (1080 * 1920 * 3)>;
width = <1080>;
height = <1920>;
stride = <(1080 * 3)>;
format = "r8g8b8";
power-domains = <&gcc MDSS_GDSC>;
clocks = <&gcc GCC_MDSS_AHB_CLK>,
<&gcc GCC_MDSS_AXI_CLK>,
<&gcc GCC_MDSS_VSYNC_CLK>,
<&gcc GCC_MDSS_MDP_CLK>,
<&gcc GCC_MDSS_BYTE0_CLK>,
<&gcc GCC_MDSS_PCLK0_CLK>,
<&gcc GCC_MDSS_ESC0_CLK>;
};
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-0 = <&hall_sensor_default>, <&volume_up_default>;
pinctrl-names = "default";
event-hall-sensor {
label = "Hall Effect Sensor";
gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
linux,input-type = <EV_SW>;
linux,code = <SW_LID>;
linux,can-disable;
wakeup-source;
};
key-volume-up {
label = "Volume Up";
gpios = <&tlmm 113 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEUP>;
};
};
leds {
compatible = "gpio-leds";
led-0 {
gpios = <&tlmm 101 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_WHITE>;
default-state = "off";
function = LED_FUNCTION_KBD_BACKLIGHT;
pinctrl-0 = <&button_backlight_default>;
pinctrl-names = "default";
};
};
reg_ts_vdd: regulator-vdd-ts {
compatible = "regulator-fixed";
regulator-name = "regulator-vdd-ts";
gpio = <&tlmm 33 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reserved-memory {
framebuffer@83000000 {
reg = <0x0 0x83000000 0x0 0x2800000>;
no-map;
};
};
vph_pwr: regulator-vph-pwr {
compatible = "regulator-fixed";
regulator-name = "vph-pwr";
regulator-always-on;
regulator-boot-on;
};
};
&blsp1_i2c2 {
status = "okay";
led-controller@30 {
compatible = "kinetic,ktd2026";
reg = <0x30>;
#address-cells = <1>;
#size-cells = <0>;
multi-led {
color = <LED_COLOR_ID_RGB>;
function = LED_FUNCTION_STATUS;
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
color = <LED_COLOR_ID_RED>;
};
led@1 {
reg = <1>;
color = <LED_COLOR_ID_GREEN>;
};
led@2 {
reg = <2>;
color = <LED_COLOR_ID_BLUE>;
};
};
};
};
&blsp1_i2c4 {
status = "okay";
nfc@28 {
compatible = "nxp,pn547", "nxp,nxp-nci-i2c";
reg = <0x28>;
interrupts-extended = <&tlmm 140 IRQ_TYPE_EDGE_RISING>;
enable-gpios = <&tlmm 122 GPIO_ACTIVE_HIGH>;
firmware-gpios = <&tlmm 109 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&nfc_default>;
pinctrl-1 = <&nfc_sleep>;
pinctrl-names = "default", "sleep";
};
};
&blsp2_i2c2 {
status = "okay";
touchscreen@20 {
reg = <0x20>;
compatible = "syna,rmi4-i2c";
interrupts-extended = <&tlmm 65 IRQ_TYPE_EDGE_FALLING>;
pinctrl-0 = <&ts_int_default>, <&ts_reset_default>;
pinctrl-1 = <&ts_int_sleep>, <&ts_reset_sleep>;
pinctrl-names = "default", "sleep";
vdd-supply = <&pm8950_l6>;
vio-supply = <®_ts_vdd>;
reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
syna,reset-delay-ms = <200>;
syna,startup-delay-ms = <200>;
#address-cells = <1>;
#size-cells = <0>;
rmi4-f01@1 {
reg = <0x1>;
syna,nosleep-mode = <1>;
};
rmi4-f12@12 {
reg = <0x12>;
syna,sensor-type = <1>;
};
};
};
&blsp2_uart2 {
status = "okay";
};
&gcc {
vdd_gfx-supply = <&pm8004_s5>;
};
&pm8004_spmi_regulators {
vdd_s2-supply = <&vph_pwr>;
vdd_s5-supply = <&vph_pwr>;
/* Cluster 1 supply */
pm8004_s2: s2 {
/* regulator-min-microvolt = <500000>; */
/* Set .95V to prevent unstabilities until CPR for this SoC is done */
regulator-min-microvolt = <950000>;
regulator-max-microvolt = <1165000>;
regulator-name = "vdd_apc1";
/* Set always on until the CPU PLL is done */
regulator-always-on;
regulator-boot-on;
};
pm8004_s5: s5 {
regulator-min-microvolt = <950000>;
regulator-max-microvolt = <1165000>;
regulator-enable-ramp-delay = <500>;
regulator-name = "vdd_gfx";
/* Hack this on until the gpu driver is ready for it */
regulator-always-on;
};
};
&pm8950_resin {
linux,code = <KEY_VOLUMEDOWN>;
status = "okay";
};
&pm8950_spmi_regulators {
vdd_s5-supply = <&vph_pwr>;
/* Cluster 0 supply */
pm8950_spmi_s5: s5 {
/* Set .95V to prevent unstabilities until CPR for this SoC is done */
/* regulator-min-microvolt = <500000>; */
regulator-min-microvolt = <950000>;
regulator-max-microvolt = <1165000>;
regulator-name = "vdd_apc0";
/* Set always on until the CPU PLL is done */
regulator-always-on;
regulator-boot-on;
};
};
&rpm_requests {
pm8950_regulators: regulators {
compatible = "qcom,rpm-pm8950-regulators";
vdd_s1-supply = <&vph_pwr>;
vdd_s2-supply = <&vph_pwr>;
vdd_s3-supply = <&vph_pwr>;
vdd_s4-supply = <&vph_pwr>;
vdd_s6-supply = <&vph_pwr>;
vdd_l1_l19-supply = <&pm8950_s3>;
vdd_l2_l23-supply = <&pm8950_s3>;
vdd_l3-supply = <&pm8950_s3>;
vdd_l5_l6_l7_l16-supply = <&pm8950_s4>;
vdd_l8_l11_l12_l17_l22-supply = <&vph_pwr>;
pm8950_s1: s1 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1162500>;
};
pm8950_s3: s3 {
regulator-min-microvolt = <1325000>;
regulator-max-microvolt = <1325000>;
};
pm8950_s4: s4 {
regulator-min-microvolt = <2050000>;
regulator-max-microvolt = <2050000>;
};
pm8950_l1: l1 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
pm8950_l2: l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
pm8950_l3: l3 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1100000>;
};
pm8950_l5: l5 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8950_l6: l6 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8950_l7: l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8950_l8: l8 {
regulator-min-microvolt = <2900000>;
regulator-max-microvolt = <2900000>;
};
pm8950_l9: l9 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3300000>;
};
pm8950_l10: l10 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
};
pm8950_l11: l11 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
};
pm8950_l12: l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
};
pm8950_l13: l13 {
regulator-min-microvolt = <3075000>;
regulator-max-microvolt = <3075000>;
};
pm8950_l14: l14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
pm8950_l15: l15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
pm8950_l16: l16 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8950_l17: l17 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
};
pm8950_l19: l19 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1350000>;
};
pm8950_l22: l22 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
};
pm8950_l23: l23 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
};
};
&sdhc_1 {
bus-width = <8>;
non-removable;
vmmc-supply = <&pm8950_l8>;
vqmmc-supply = <&pm8950_l5>;
status = "okay";
};
&sdhc_2 {
bus-width = <4>;
cd-gpios = <&tlmm 100 GPIO_ACTIVE_LOW>;
vmmc-supply = <&pm8950_l11>;
vqmmc-supply = <&pm8950_l12>;
pinctrl-0 = <&sdc2_default>, <&sdc2_cd_default>;
pinctrl-1 = <&sdc2_sleep>, <&sdc2_cd_sleep>;
pinctrl-names = "default", "sleep";
status = "okay";
};
&tlmm {
gpio-reserved-ranges = <0 4>;
button_backlight_default: button-backlight-default-state {
pins = "gpio101";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
hall_sensor_default: hall-sensor-default-state {
pins = "gpio107";
function = "gpio";
drive-strength = <6>;
bias-pull-up;
};
nfc_default: nfc-default-state {
pins = "gpio122", "gpio140";
function = "gpio";
drive-strength = <6>;
bias-pull-up;
};
nfc_sleep: nfc-sleep-state {
int-pins {
pins = "gpio140";
function = "gpio";
drive-strength = <6>;
bias-pull-up;
};
ven-pins {
pins = "gpio122";
function = "gpio";
drive-strength = <6>;
bias-disable;
};
};
sdc2_cd_default: sdc2-cd-default-state {
pins = "gpio100";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
sdc2_cd_sleep: sdc2-cd-sleep-state {
pins = "gpio100";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
ts_int_default: ts-int-state {
pins = "gpio65";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
ts_int_sleep: ts-int-state {
pins = "gpio65";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
ts_reset_default: ts-reset-state {
pins = "gpio64";
function = "gpio";
drive-strength = <8>;
bias-pull-up;
};
ts_reset_sleep: ts-sleep-state {
pins = "gpio64";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
volume_up_default: volume-up-default-state {
pins = "gpio113";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
&xo_board {
clock-frequency = <19200000>;
};
[ Dauer der Verarbeitung: 0.11 Sekunden
(vorverarbeitet)
]
